1. DL manuals
  2. National Instruments
  3. Network Hardware
  4. PXI Terminal Block NI TB-2709
  5. Installation Manual

National Instruments PXI Terminal Block NI TB-2709 Installation Manual

Manual is about: PXI Terminal Block for S Series Devices

Summary of PXI Terminal Block NI TB-2709

  • Page 1

    Installation guide ni tb-2709 pxi terminal block for s series devices this installation guide describes how to install and connect signals to the ni tb-2709 terminal block for use with pxi-6123/6133 s series devices. The tb-2709 can also be used with the pxi-6122/6132 devices to access the first fou...

  • Page 2: Safety Information

    Ni tb-2709 installation guide 2 ni.Com the nine smb connectors on the tb-2709 allow you to easily connect analog input signals to your national instruments device. The 14-pin i/o connector located on the bottom of the tb-2709 allows access to digital signals. Caution the tb-2709 is not designed for ...

  • Page 3: Installation

    © national instruments corporation 3 ni tb-2709 installation guide do not substitute parts or modify equipment. Because of the danger of introducing additional hazards, do not install unauthorized parts or modify the device. Return the device to national instruments for service and repair to ensure ...

  • Page 4: Signal Descriptions

    Ni tb-2709 installation guide 4 ni.Com to connect the terminal block to the pxi module i/o connector, refer to figure 2 as you complete the following steps: 1. Install the pxi module into the chassis and tighten the two module screws. You must install the pxi device before connecting the tb-2709. Re...

  • Page 5

    © national instruments corporation 5 ni tb-2709 installation guide figure 4. Ni tb-2709 block diagram for more detailed descriptions of these signals, refer to the s series user manual . Additional signal configuration information is available in measurement & automation explorer (max). To access th...

  • Page 6: Cabling Options

    Ni tb-2709 installation guide 6 ni.Com measuring ground-referenced signals it is possible to set the switch on the tb-2709 to either the floating or ground-referenced source position to measure ground-referenced signals. However, for best results, use the off (ground-referenced source) switch positi...

  • Page 7

    © national instruments corporation 7 ni tb-2709 installation guide conductors on the other end. The pigtail conductors on the cable assembly can be used to terminate digital signals to the connector(s) your application requires. Figure 5 and table 3 list the pin assignments and wiring information ne...

  • Page 8: Specifications

    Ni tb-2709 installation guide 8 ni.Com table 4 lists the national instruments cables available for connecting the tb-2709 to both analog and digital user signals. Specifications this section lists the specifications of the tb-2709. These specifications are typical at 25 °c unless otherwise specified...

  • Page 9

    © national instruments corporation 9 ni tb-2709 installation guide physical dimensions height.............................................. 10.7 × 8.6 × 2.0 cm (4.2 × 3.4 × 0.8 in.) weight............................................. 144.6 g (5.1 oz) i/o connectors 68-position scsi-ii type ............

  • Page 10: Where To Go For Support

    Ni tb-2709 installation guide 10 ni.Com safety this product is designed to meet the requirements of the following standards of safety for electrical equipment for measurement, control, and laboratory use: • iec 61010-1, en 61010-1 • ul 61010-1, csa 61010-1 note for ul and other safety certifications...

  • Page 11

    © national instruments corporation 11 ni tb-2709 installation guide finland 385 (0) 9 725 72511, france 33 (0) 1 48 14 24 24, germany 49 89 7413130, india 91 80 41190000, israel 972 3 6393737, italy 39 02 413091, japan 81 3 5472 2970, korea 82 02 3451 3400, lebanon 961 (0) 1 33 28 28, malaysia 1800 ...

  • Page 12

    National instruments, ni, ni.Com, and labview are trademarks of national instruments corporation. Refer to the terms of use section on ni.Com/legal for more information about national instruments trademarks. Other product and company names mentioned herein are trademarks or trade names of their resp...