Summary of Atomos shogun
Page 1
0
Page 2
1 thank you for your purchase of a nauticam housing. At nauticam, we pride ourselves in the ability to recognise the requirements of professional as well as amateur underwater photographers and fulfill them through the innovative designs of our products. We strive to achieve a high level of user-fri...
Page 3
2 1. All nauticam products are warranted against any material and manufacturing defects for one year from the date of purchase for consumer use. Please fill in the warranty cards shipped with our housings and viewfinders at the time of sale and return them to your point of purchase within a month. I...
Page 4
3 1. Nauticam atomos shogun housing 2. Hdmi bulkhead with integrated cable and type d connector 3. Instruction manual 4. Hand pump 5. Spare silicone rubber main o-ring 6. O-ring remover 7. Cr2032 battery (vacuum check and leak detection system) 8. Lubricant 9. Set of allen keys spare silicone rubber...
Page 5
4 1. A water-tight test without the monitor inside the housing is highly recommended when using the system for the first time and after the changing of port and o-ring(s). 2. Do not use lubricants from other brands with the silicone rubber o-ring on this housing, only use the lubricant provided by n...
Page 6
5 specifications 6 identification of parts 7 opening and locking the housing 8 preparation of the housing 9 installing the monitor 13 connecting to the camera housing 14 care and maintenance 16 optional accessories 17.
Page 7
6 construction housing body: aluminium alloy surface treatment: hard anodised display window: abrasion resistant polycarbonate dimensions width: 286mm height: 176mm depth: 120mm weight approx. 2.35kg buoyancy positive depth rating 60 metres operating temperature normal operating temperature is betwe...
Page 8
7 1 hdmi cable 10 fan indicator 2 moisture alarm window 11 m14 accessory port 3 m16 vacuum valve 12 fan on/off button 4 threaded holes for monitor hood (4x) 13 monitor on/off button 5 rec button 14 housing lock safety button 6 play button 15 housing lock 7 1/4" threaded holes attachment points (4x) ...
Page 9
8 to open the housing: to lock the housing: 1. Press the housing lock safety button. 2. Turn the housing lock anti- clockwise for 270°, until the lock reaches the “open” position as shown. 3. Close the housing while the housing lock is in the “open” position. 4. Turn the housing lock clockwise for 2...
Page 10
9 1. After verifying that the main o-ring is in good condition, lightly coat it with the lubricant provided. 2. Make sure the o-ring groove located in the front part of the housing is free from any foreign material; the groove can be cleaned with the aid of a microfiber cloth. 3. Place the main o-ri...
Page 11
10 1. Install the cr2032 battery provided into the battery compartment on the circuit board inside the front part of the housing. 5. Setting up the moisture alarm: 2. Switch the alarm on. The led light will flash blue once and turn blue for five seconds indicating the battery is normal. Then it goes...
Page 12
11 1. Remove the vacuum valve cap. 2. Make sure the vacuum release ring is at its closed position by turning it clockwise until it cannot go any further. 5. Please ensure that the cap is attached back to the vacuum valve before going underwater. 6. Vacuum can be released by turning the vacuum releas...
Page 13
12 led status identification: on start up: led indicator status flash “blue” light once indicates a 2nd generation pcb steady "blue" light battery is normal, goes into flashing "blue" light standby mode after 5 seconds. "blue" and "red" lights alternating battery low. Replace battery as soon as poss...
Page 14
13 to install the monitor into the housing: 1. Turn the three locking levers in the direction as shown. 3. Secure the monitor by turning the three locking levers towards the monitor as shown. 2. Connect the hdmi cable with "l " connector to the monitor. 4. Place the monitor inside the housing as sho...
Page 15
14 to install the standard hdmi bulkhead: ii. Insert the hdmi bulkhead with cable into the hole and tighten the it with a spanner. Iii. Connect the hdmi cable to the camera's hdmi connector. I. Unscrew the m16 plug from the threaded hole with a coin..
Page 16
15 to connect the monitor housing to hdmi bulkhead: i. Unscrew the cap off the hdmi bulkhead. Ii. Unscrew the cap off the hdmi cable. Iii. Align and plug the hdmi cable in the hdmi bulkhead. Tighten the connection by turning the threaded ring on the hdmi cable.
Page 17
16 1. Soak the housing system in fresh water after each salt water use, during which all control buttons/knobs should be operated a few times to avoid the accumulation of salt residue; wipe the housing with a towel before opening. 2. Carefully press the housing lock safety button for a few times to ...
Page 18
17 p.N. 17914 monitor hood for nauticam atomos shogun housing p.N. 17951 nauticam atomos shogun housing mounting system p.N. 17952 nauticam atomos shogun housing mounting adaptor for na-a7s p.N. 17953 nauticam atomos shogun housing mounting adaptor for na-gh4.
Page 19
18 p.N. 17954 tripod plate for na-a7s and na-gh4.
Page 20
19.