Summary of NA-G7X
Page 1
0
Page 2
1 thank you for your purchase of a nauticam camera housing. At nauticam, we pride ourselves in the ability to recognise the requirements of professional as well as amateur underwater photographers and fulfill them through the innovative designs of our products. We strive to achieve a high level of u...
Page 3
2 1. All nauticam products are warranted against any material and manufacturing defects for one year from the date of purchase for consumer use. Please fill in the warranty cards shipped with our housings and viewfinders at the time of sale and return them to your point of purchase within a month. I...
Page 4
3 1. Na-g7x housing 2. Instruction manual 3. Spare silicone rubber housing o-ring 4. O-ring remover 5. Cr2032 battery (for moisture alarm) 6. Lubricant 7. Set of allen keys spare silicone rubber o-ring o-ring remover cr2032 battery lubricant set of allen keys.
Page 5
4 1. A water-tight test without the camera inside the housing is highly recommended when using the system for the first time and after the changing of port and o-ring(s). 2. Do not use lubricants from other brands with the silicone rubber o- ring on this housing, only use the lubricant provided by n...
Page 6
5 specifications 6 identification of parts 7 opening and locking the housing 9 preparation of the housing 10 installing the camera 13 changing the port 14 care and maintenance 16 optional accessories 17.
Page 7
6 construction housing body: aluminium alloy surface treatment: hard anodised display window: abrasion resistant polycarbonate dimensions width: 146mm height: 101mm depth: 109mm weight approx. 0.88kg (without camera) buoyancy slightly negative depth rating 100 metres features moisture alarm: blinkin...
Page 8
7 1 on/off button 9 moisture alarm window 2 mode dial 10 m10 strobe mounting base 3 exposure compensation dial 11 flash up lever 4 zoom lever 12 accessory coldshoe 5 zoom lever lock 13 optical fibre mount 6 shutter release lever 14 port alignment index 7 front control wheel 15 port lock safety butto...
Page 9
8 17 mounting holes for lcd magnifier attachment rails 24 func./set button 18 ring function selector/ erase button 25 display/ down button 19 movie button 26 menu button 20 rear control wheel 27 playback button 21 drive mode/ wi-fi/ up button 28 housing lock safety button 22 macro/ mf/ left button 2...
Page 10
9 to open the housing: to lock the housing: 2. Turn the housing lock anti- clockwise for 270°, until the lock reaches the “open” position as shown. 3. Close the housing while the housing lock is in the “open” position. 4. Turn the housing lock clockwise for 270°, until the lock reaches the “lock” po...
Page 11
10 1. After verifying that the housing o-ring is in good condition, lightly coat it with the lubricant provided. 2. Make sure the o-ring groove located in the rear part of the housing is free from any foreign material; the groove can be cleaned with the aid of a microfiber cloth. 3. Place the o-ring...
Page 12
11 1. Install the cr2032 battery provided into the battery compartment on the circuit board inside the front part of the housing. 4. Setting up the moisture alarm: 3. Test the alarm by contacting the two wires near the bottom of the housing with a damped cotton bud; the alarm should start giving out...
Page 13
12 led status identification: on start up: led indicator status steady "blue" light battery is normal, goes into flashing "blue" light standby mode after 5 seconds. "blue" and "red" lights alternating battery low. Replace battery as soon as possible. Goes into standby mode after 5 seconds. Steady "r...
Page 14
13 1. Place the camera inside the housing as shown. Note that the camera should be inserted from the left first to avoid interfere with the strap mount and housing. 2. Confirm that all the controls of the housing are correctly engaged..
Page 15
14 1. Press and hold the red port lock safety button to un-lock. 2. While holding the red port lock safety button, turn the port anti- clockwise until the "i" mark on the port aligns with the "o" mark on the housing. Then gently pull the port out. Two optional ports are available for different style...
Page 16
15 3. Align the "i" mark on the port with the "o" mark on the housing. 4. Gently push the port towards the housing until it cannot go any further. 5. Turn the port clockwise until the "o" mark on the port aligns with the "o" mark on the housing. To mount port:.
Page 17
16 1. Soak the housing system in fresh water after each salt water use, during which all control buttons/knobs should be operated a few times to avoid the accumulation of salt residue; wipe the housing with a towel before opening. 2. After each day of diving, it is advisable to have the main o-ring ...
Page 18
17 p.N. 25123 lcd magnifier attachment rails for na-s110/s120/tg3/g7x p.N. 25611 m14 vacuum valve p.N. 25106 lcd magnifier with dioptric adjustment p.N. 38022 diffuser for na-g7x housing.
Page 19
18 p.N. 38701 n50 short port with m67 thread for wet wide angle lenses (widest focal length only) p.N. 38702 n50 3.5'' acrylic dome port.
Page 20
19.