Summary of NA-RX100
Page 1
0
Page 2
1 thank you for your purchase of a nauticam camera housing. At nauticam, we pride ourselves on the ability to recognise the requirements of professional as well as amateur underwater photographers and fulfill them through the innovative designs of our products. We strive to achieve a high level of u...
Page 3
2 1. All nauticam products are warranted against any material and manufacturing defects for one year from the date of purchase for consumer use. 2. Nauticam accepts no liability for any damage to and defects in the housing caused by improper use and/or poor maintenance; it is the responsibility of t...
Page 4
3 1. Na-rx100/ rx100v housing 2. Instruction manual 3. Spare silicone rubber housing o-ring 4. O-ring remover 5. Cr2032 battery (for moisture alarm) 6. Lubricant 7. Set of allen keys 8. Hdmi bulkhead with socket extension (for na-rx100v) 9. Hdmi (d-d) cable (for na-rx100v) hdmi bulkhead with socket ...
Page 5
4 1. A water-tight test without the camera inside the housing is highly recommended when using the system for the first time and after the changing of port and o-ring(s). 2. Do not use lubricants from other brands with the silicone rubber o- ring on this housing, only use the lubricant provided by n...
Page 6
5 specifications 6 identification of parts 7 preparation of the housing 9 opening and locking the housing 11 installing the camera 12 installing the hdmi bulkhead (na-rx100v) 13 care and maintenance 15 optional accessories 16.
Page 7
6 construction housing body: aluminium alloy surface treatment: hard anodised display window: abrasion resistant polycarbonate dimensions width: 144mm/ 152mm (na-rx100v) height: 102mm/ 116mm (na-rx100v) depth: 102mm/ 103mm (na-rx100v) weight approx. 0.77kg / 0.81kg (na-rx100v) (without camera) buoya...
Page 8
7 1 m10 strobe mounting base 6 front control wheel 2 on/off button 7 accessory coldshoe 3 zoom lever 8 optical fibre mount 4 mode dial 9 port with 67mm thread 5 shutter release lever 1 2 3 4 7 6 8 5 9.
Page 9
8 10 moisture alarm window 18 tracking focus/ set button 11 movie button 19 exposure compensation/ down selection button 12 fn button 20 in-camera guide/ delete button 13 menu button 21 playback button 14 rear control wheel 22 housing lock safety button 15 display/ up selection button 23 housing loc...
Page 10
9 1. After verifying that the housing o-ring is in good condition, lightly coat it with the lubricant provided. 2. Make sure the o-ring groove located in the rear part of the housing is free from any foreign material; the groove can be cleaned with the aid of a microfiber cloth. 3. Place the o-ring ...
Page 11
10 setting up the moisture alarm 1. Install the cr2032 battery provided into the battery compartment on the circuit board inside the rear part of the housing. 2. Test the alarm by contacting the two wires near the bottom of the housing with a damped cotton bud; the alarm should start giving out a re...
Page 12
11 to open the housing: to lock the housing: 2. Turn the housing lock anti- clockwise for 270°, until the lock reaches the “open” position as shown. 3. Close the housing while the housing lock is in the “open” position. 4. Turn the housing lock clockwise for 270°, until the lock reaches the “lock” p...
Page 13
12 1. Place the camera inside the housing as shown. 2. Confirm that all the controls of the housing are correctly engaged..
Page 14
13 1. Unscrew the m16 plug from the threaded hole with a coin. 2. Tighten the socket extension to the camera housing with a spanner. 3. Open the housing and insert the hdmi cable through the threaded hole from inside of the housing..
Page 15
14 4. Connect the hdmi cable to the hdmi bulkhead. 5. Tighten the hdmi bulkhead by turning the threaded ring on the socket extension. 6. Connect the hdmi cable to the camera's hdmi connector before placing the camera inside the housing. Please refer to the na-dp4 manual for connecting na-dp4 housing...
Page 16
15 1. Soak the housing system in fresh water after each salt water use, during which all control buttons/knobs should be operated a few times to avoid the accumulation of salt residue; wipe the housing with a towel before opening. 2. After each day of diving, it is advisable to have the main o-ring ...
Page 17
16 p.N. 38016 diffuser for na-rx100 housing p.N. 25101 m67 flip diopter holder for m67 macro port.
Page 18
17.