1. DL manuals
  2. Nautilus
  3. TV Mount
  4. Be Strong. M-Series LCD Monitor Bracket
  5. Installation Manual

Nautilus Be Strong. M-Series LCD Monitor Bracket Installation Manual - Installation Procedure

Summary of Be Strong. M-Series LCD Monitor Bracket

  • Page 1

    Be strong. ™ model:nv915 p/n: 001-1959 rev c (08/13/2007) installation manual m-series lcd monitor bracket.

  • Page 2: Table of Contents

    Table of contents fcc information 3 safety precautions 4 specifications components & tools needed 5 installation procedure 6 quick reference guide 17 important contact information 18.

  • Page 3: Fcc Information

    3 nautilus ® lcd installation fcc information this equipment has been tested and found to comply with limits for a class b digital device, pursuant to part 15 of the fcc rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This...

  • Page 4: Important Safety Precautions

    4 important safety precautions wa r n i n g important! To reduce the risk of fire, electrical shock or other injuries, follow these safety precautions when installing, using and maintaining your nv915 lcd tv monitor. • any changes or modifications in construction of this device which are not express...

  • Page 5

    5 nautilus ® lcd installation box 1 contents lcd bracket part # 000-8082 console spacer part # 001-1894 hardware pack part # 001-1916 box 2 contents lcd monitor part # 001-1924 us (ntsc) part # 001-1992 (pal) part # 002-3782 us (digital) power cord part # 001-1922 us part # 001-2015 continental part...

  • Page 6: Installation Procedure

    6 installation procedure step 1 remove the console tools needed: phillips head screwdriver 1-1 use a phillips head screwdriver to remove the four screws that secure the console. Tools needed: wire cutter or similar 2-1 locate the lcd wires inside the mast. (figure a) 2-2 remove the wire tie. (figure...

  • Page 7: Installation Procedure

    7 nautilus ® lcd installation installation procedure step 3 place spacer between console and mast tools needed: phillips head screwdriver 4-1 use a phillips head screwdriver to remove the four screws and washers securing the back cover to the bracket. Step 4 remove the back cover of the lcd bracket ...

  • Page 8: Installation Procedure

    8 installation procedure step 5 attach the lcd bracket parts needed: lcd bracket four 1/4” x 1” phillips head screws tools needed: phillips head screwdriver 5-1 pass the lcd wires through the bracket between the metal plate and the plastic cover as shown. (figure a) 5-2 align the bracket with the co...

  • Page 9: Installation Procedure

    9 nautilus ® lcd installation installation procedure step 6 prepare to install the lcd monitor note: to keep the lcd wires in place, it is helpful to pass them through the bracket as shown. Tools needed: phillips head screwdriver 6-1 use a phillips head screwdriver to remove the back cover of the lc...

  • Page 10: Installation Procedure

    10 installation procedure step 7 attach the lcd monitor tools needed: 6mmallen wrench 7-1 position the lcd monitor on the bracket (figure a) with the metal tabs resting between the upright prongs discussed in step 6. (detail a) 7-2 install the m10 allen bolts and lock washers. (from hardware kit) 7-...

  • Page 11: Installation Procedure

    11 nautilus ® lcd installation installation procedure step 8 connect wires to monitor the connections shown are for pre wired units with coaxial and power connections only. For alternative configurations please refer to the lcd monitor owners manual. Important! You must wire tie the power wire to th...

  • Page 12: Installation Procedure

    1 installation procedure step 9 replace the back covers tools needed: phillips head screwdriver 9-1 use the m4 screws and washers from the hardware kit to replace the back cover of the bracket (figure a) and the lcd monitor. (figure b) note: use the two longer screws on the raised portion of the lcd...

  • Page 13

    13 nautilus ® lcd installation commercial bikes installation procedure mounting plate secure the power brick to the power connector and the coaxial cable to the coax connector on the mounting plate as shown. Tv coax connector power for unit tv power connector attention: after steps 1-9 of the m-seri...

  • Page 14: Installation Procedure

    14 step 10 remove right shroud tools needed: phillips head screwdriver 10-1 use a phillips head screwdriver to remove the right shroud. Installation procedure right shroud step 11 secure the power “brick” to the frame tools needed: two wire ties 11-1 connect the power wire to the power connection on...

  • Page 15: Installation Procedure

    15 nautilus ® lcd installation step 12 route the lcd wires 12-1 connect the coaxial cable and route the lcd wires over the top, behind and under the frame junction as shown. Installation procedure coaxial connection route wires behind frame junction step 13 replace right shroud tools needed: phillip...

  • Page 16: Installation Procedure

    Installation procedure installation is complete. For specific instructions on setup and use of the lcd monitor please refer to the lcd monitor users manual 16.

  • Page 17: Quick Reference Guide

    17 nautilus ® lcd installation quick reference guide 1 2 3 4 5 6 1 2 3 4 5 6 power volume up video input source (video/s-video, antenna) volume down mute channel down 7 8 7 channel up 8 numeric channel keys headphone jack infrared (remote) receiver power light for specific instructions on setup and ...

  • Page 18: International Offices:

    18 important contact numbers offices in the united states: e-mail: cstech@nautilus.Com • technical/customer service nautilus, inc. World headquarters 16400 se nautilus drive vancouver, washington, usa 98683 phone: 800-nautilus (800-628-8458) fax: 877-686-6466 • corporate headquarters nautilus, inc. ...

  • Page 19

    Be strong. ™ for more information about our lcd tv monitor or other nautilus ® equipment , visit www.Nautilusinc.Com. © 2007 nautilus, inc. All rights reserved. Nautilus, the nautilus logo, and be strong are either registered trademarks or trademarks of nautilus, inc. All other marks are either regi...