Nautilus Be Strong TreadClimber TC916 Assembly Manual - 7 ! 2 . ) . '

Other manuals for Be Strong TreadClimber TC916: Owner's Manual, Service Manual
Manual is about: Commercial Series

Summary of Be Strong TreadClimber TC916

  • Page 1

    Be strong. ™ p/n:001-7013revb(11/09/2006) assemblymanual treadclimber® model tc916 commercial series.

  • Page 2: 7 ! 2 . ) . '

    For detailed instructions and information on how to use and care for your treadclimber ® commercial series exercise machine, model tc916, refer to the owner’s manual. 7 ! 2 . ) . ' ! 4 4 % . 4 ) / . $ ! . ' % 2 )--%$)!4%!#4)/.2%15)2%$ # ! 5 4 ) / ..

  • Page 3

    Nautilus® treadclimber® model tc916 assembly manual table of contents treadclimber ® features ............................................................................................................................ 4 productspecifications ............................................................

  • Page 4

    4 treadclimber ® features console ergo bar power on/off switch adjustable feet model: tc916.

  • Page 5

    Nautilus® treadclimber® model tc916 assembly manual product specifications user weight capacity: 400 lbs (182 kg) speed range: 0.5 to 6 mph (default set to 4.0 mph) 0.8 to 9.7 km/h (default set to 6.4 km/h) treadle displacement levels: min (half the total displacement) and max (full treadle displace...

  • Page 6: 7 ! 2 . ) . '

    6 important safety precautions save these instructions: the following definition applies to the word “warning” found throughout this manual: used to call attention to potential hazards that could result in personal injury or loss of life. When using electrical equipment always follow these basic pre...

  • Page 7

    Nautilus® treadclimber® model tc916 assembly manual 6. Before each use of this equipment, check the power receptacle for signs of damage. Do not operate the equipment if the integrity of the power receptacle is in question. 7. To avoid potential safety and electrical problems, replace with manufactu...

  • Page 8: Timeperiod

    Commercial market warranty information **forwarrantyinformationoutsideoftheunitedstatesorcanada, contacttheinternationalofficelistedintheimportantcontactnumberssectionofthismanual.** warranty information all nautilus ® exercise products are warranted to the commercial market purchaser to be free fro...

  • Page 9: Selectyourworkoutarea

    9 nautilus® treadclimber® model tc916 assembly manual getting started getting started selectyourworkoutarea select the location where you are going to put your nautilus ® treadclimber ® exercise machine carefully. The best place for your treadclimber ® machine is on a hard, level surface. You will n...

  • Page 10: Safetystop

    10 getting started limitedaccesscontrol/magnetic safetystop limited-access control lets you restrict treadclimber ® machine use to authorized personnel. It also lets you stop the treadclimber ® machine in an emergency. The magnetically-activated control is located on the bottom of the display as sho...

  • Page 11: Quickstartguide

    11 nautilus® treadclimber® model tc916 assembly manual getting started to start: insert the magnetic safety stop key and press the [quick start] key , or select a program key . To stop: press [stop] to pause the workout. Press [stop] again to end the workout. During the workout: • after selecting a ...

  • Page 12: 7 ! 2 . ) . '

    1 moving instructions delivery logistics the treadclimber ® tc916 may be delivered fully-assembled, shipped on a pallet crate, and blanket wrapped; • pallet crate shipping weight: 806 pounds • unit weight: 684 pounds - or - delivered in a one box configuration, requiring assembly. • boxed unit shipp...

  • Page 13: Removingmachinefrompallet

    1 nautilus® treadclimber® model tc916 assembly manual removingmachinefrompallet tools needed: 7/16 socket ratchet step 1: remove tc916 from pallet by removing restraining stabilizer brackets with socket and ratchet from stabilizer feet (see figure 1). Step 2: manually slide tc916 to one side of the ...

  • Page 14: 7! 2 . ) . '

    14 tools needed: 7/16 socket ratchet moving dolly lift bar step 1: remove tc916 from pallet by performing steps in section “removing machine from pallet” in this manual. Step 2: tilt to 40 degrees (see figure 1). While tilted place 4-wheel moving dolly under center of treadclimber ® frame (see figur...

  • Page 15

    1 nautilus® treadclimber® model tc916 assembly manual moving instructions step 5: carefully tilt treadclimber ® machine onto one-side of frame towards ground (see figure 4). Step 6: tilt unit to 40 degrees and remove moving dolly. Step 7: place moving tool under the machine according to the “moving ...

  • Page 16: Importantinformationtoread

    16 importantinformationtoread beforedisassemblinguprightunit. During delivery of this unit it may become necessary to disassemble the upright portion of the unit to reduce the size and weight. The upright portion of the unit has wheels integrated into it, making it possible to wheel it away from the...

  • Page 17: 7 ! 2 . ) . '

    1 nautilus® treadclimber® model tc916 assembly manual moving instructions 1.0 removing rear step tools needed: • phillips head screw driver • magnetic 3/8” nut driver with long shaft • magnetic 3/8” socket • ratchet step 1: unplug the unit from the power source and ensure that all power has been dra...

  • Page 18: 7 ! 2 . ) . '

    1 2.0 removing uprights tools needed: • phillips head screw driver • 5/32 allen wrench • 3/4 inch wrench or socket • 1/2 inch drive ratchet • 1/2 inch drive torque wrench step 1: remove for the four button head screws at- taching the console to the upright weldment, disconnect the cables and remove ...

  • Page 19

    19 nautilus® treadclimber® model tc916 assembly manual moving instructions note: you should only use this step if you need to rotate the lower base unit up onto its side to transport it. 3.0 removing base plastic tools needed: 1/8 allen bit step 1: remove three (3) front plastic screws (see figure 3...

  • Page 20: Movingtoolinformation

    0 moving instructions movingtoolinformation figure 1 figure 2 frame wheel clevis clip moving tool parts: the following parts are shown in the figure to the right, in order listed: • wheel bar – one frame, two wheels, two clevis clips • caster cart – one base, two wheels • lifting tool – one piece • ...

  • Page 21

    1 nautilus® treadclimber® model tc916 assembly manual moving instructions step 5: on the right side, lift the machine and remove the block of wood, lowering the machine onto the caster cart and wheel bar, ensuring the wheels are straight. Step 6 : on the left side, lift the machine and remove the bl...

  • Page 22: Basicassemblyprinciples

    Assembly instructions before you assemble basicassemblyprinciples here are a few basic assembly tips that can make assembly of your nautilus ® commercial treadclimber ® exercise machine quick and easy. 1. You can make the assembly process go faster by gathering the pieces you need for each step prio...

  • Page 23: Toolsneeded:

    Nautilus® treadclimber® model tc916 assembly manual assembly instructions hardware and tool list toolsneeded: (not provided) • 3/4 inch socket, for a 1/2 inch drive ratchet • 1/2 inch drive ratchet • 7/32 allen bit • 5/32 allen bit • 1/8 allen bit • torque wrench with 1/2 inch drive • phillips screw...

  • Page 24: Partslistreferenceguide

    4 assembly instructions qty: 1 descr: rear step cover part number: 17733 qty: 1 descr: left bottom plastic pivot cover part number: 17918 qty: 1 descr: console assembly part number: 17670 - domestic 17835 - tv, domestic 17837 - tv, international qty: 1 descr: one rear motor cover part number: 17874 ...

  • Page 25

    Nautilus® treadclimber® model tc916 assembly manual assembly instructions qty: 1 descr: tc916 treadclimber ® base assembly part number: 17500 qty: 1 descr: tc916 treadclimber ® handrail assembly part number: 17793 qty: 1 descr: tc916 treadclimber ® handrail upright support assembly part number: 1779...

  • Page 26: Unpackingguide

    6 assembly instructions unpackingguide the following instructions provide direction in unpacking the boxed unit for the nautilus ® commercial series treadclimber ® model tc916. Step1:openingcrate tools: • scissors or utility knife 1-1 remove the outer cardboard to reveal the contents of crate. Step2...

  • Page 27: Step3:verifyingboxcontents

    Nautilus® treadclimber® model tc916 assembly manual assembly instructions step3:verifyingboxcontents locate the following for this step: • box 1 - parts master carton • box 2 - top plate carton • box 3 - short side panel carton tools: • scissors or utility knife 3-1 verify the contents of box 1: “pa...

  • Page 28: Step4:dismantlingcrate

    Assembly instructions step4:dismantlingcrate tools: • hammer 4-1 carefully dismantle the wooden crate to allow access to the bottom half of the treadclimber ® tc916 frame. Note: the treadclimber ® tc916 base frame should be close to the final location for the fully assembled machine during this step...

  • Page 29: Assemblyguide

    9 nautilus® treadclimber® model tc916 assembly manual assembly instructions assemblyguide the following instructions provide direction in assembling the boxed units for the nautilus ® commercial series treadclimber ® model tc916. All instructions in the manual are given with the orientation of stand...

  • Page 30

    0 assembly instructions locate the following for this step: parts: • assembly from step 1 hardware: • 4 bolts (p/n 17683) • 4 lock washers (p/n - 22222) • 4 washers (p/n 22091) tools: • 3/4 inch socket for 1/2 drive • torque wrench (1/2 inch), set at 75 ft. Lbs. (100 nm) • 1/2 inch drive ratchet 2-1...

  • Page 31

    1 nautilus® treadclimber® model tc916 assembly manual assembly instructions figure 3: connecting ground wire straps locate the following for this step: parts: • assembly from step 2 • 3 grounding straps hardware: • 4 self-tapping screws - .25 x .50 (p/n 22139) • 5 lock washers (p/n - 41260) tools: •...

  • Page 32

    Step4:connectingwiringharnessfromuprightsupportstohandrails locate the following for this step: parts: • assembly from step 3 • handrail assembly (p/n - 17793) 4-1 connect the wiring harness (p/n - 17824) from the handrail upright support assembly (p/n - 17794) to the handrail assembly. See figure 4...

  • Page 33

    Nautilus® treadclimber® model tc916 assembly manual step5:connectinghandrailsupporttobaseassembly locate the following for this step: parts: • assembly from step 4 hardware: • 8 screws (p/n 25796) • 8 washers (p/n 17775-007) tools: • 7/32 allen bit 5-1 bolt handrail assembly (p/n - 17793) to handrai...

  • Page 34

    4 base assembly step6:connectingwiringharnesstoconsole locate the following for this step: parts: • assembly from step 5 • console (p/n 17670) 6-1 connect the wiring harness from the handrail upright support assembly (p/n - 17794) to console (p/n - 17670) on the left and right side. See figure 6. No...

  • Page 35: Step7:securingconsole

    Nautilus® treadclimber® model tc916 assembly manual assembly instructions step7:securingconsole locate the following for this step: parts: • assembly from step 6 hardware: • 4 screws (p/n 24162) tools: • 5/32 allen bit 7-1 align the holes on the tubing of the console with the holes on the handrail a...

  • Page 36

    6 assembly instructions step9:attachingrearmotorcover locate the following for this step: parts: • assembly from step 8 • rear motor cover (p/n 17874) hardware: • 6 screws (p/n - 17815) • 6 washers (p/n 17578) tools: • phillips screw driver 9-1 attach the rear motor cover using 6 screws and 6 washer...

  • Page 37

    Nautilus® treadclimber® model tc916 assembly manual locate the following for this step: parts: • assembly from step 9 • rear step weldment (p/n 17591) • rear step cover (p/n 17733) hardware: • 2 screws (p/n - 17809) • 2 washers (p/n - 22637) • 2 screws (p/n - 17695) • 1 self-tapping screws - .25 x ....

  • Page 38: Step12:installingpowercord

    Step11:attachinguprightplasticcovers locate the following for this step: parts: • assembly from step 10 • right upright plastic cover (p/n - 17668) • left upright plastic cover (p/n - 17669) hardware: • 16 screws (p/n - 17815) • 16 washers (p/n - 17578) tools: • 1/8 allen bit 11-1 on the right side,...

  • Page 39: Step14:inspectingassembly

    9 nautilus® treadclimber® model tc916 assembly manual step14:inspectingassembly congratulations! Now that you have assembled your nautilus ® treadclimber ® model tc916, it is very important to tighten all screws and bolts, and visually inspect the treadclimber ® exercise machine. If your treadclimbe...

  • Page 40

    40 belt tension and alignment figure 1 figure 2: belts are correctly aligned when 1/8 inch of roller is showing. Figure 3: tension is too tight, treadle guards are rubbing. To correct loosen tensioning adjustment screw. Alignment adjustment tensioning adjustment tension is slightly off. During initi...

  • Page 41

    41 nautilus® treadclimber® model tc916 assembly manual important contact numbers officesintheunitedstates: • technical/customer service nautilus, inc. World headquarters 16400 se nautilus drive vancouver, washington, usa 98683 phone: 800-nautilus (800-628-8458) email: customerservice@nautilus.Com fa...

  • Page 42

    4 page intentionally left blank.

  • Page 43

    4 nautilus® treadclimber® model tc916 assembly manual page intentionally left blank.

  • Page 44

    ©2006. Nautilus, inc. All rights reserved. Nautilus, the nautilus logo, treadclimber, and be strong are either registered trademarks or trademarks of nautilus, inc. Nautilus, inc. World headquarters 16400 se nautilus drive, vancouver, washington, usa 98683 1-800-nautilus www.Nautilus.Com modeltc916.