Model: ev716 & ev718 p/n: 000-3603 rev d (5/05/2007) assembly manual pro series elliptical ev 718 model ev 716 model.
Important safety precautions save these instructions the following definition applies to the word “warning” found throughout this guide: read all instructions 1. Read, understand and carefully follow all warnings, instructions and procedures in this manual. Failure to do so can produce a serious ele...
Nautilus® pro series elliptical assembly manual hardware required assembly tools • torque wrench • 10 mm allen wrench • 13 mm box wrench • 19mm socket • 6 mm allen wrench • adjustable wrench • 17mm socket • 8 mm allen wrench • long and short #2 phillips screw drivers • 3/8” drive ratchet with 6mm, 8...
4 reference chart actual size hardware reference chart # 17 m 12 x 7 0m m a lle n h ea d b ol t # 1 2 0m m a lle n h ea d b ol t # 2 1/ 2” s pr in g w as he r # 6 15 m m p hi lli ps h ea d s cr ew # 10 7 0m m h ex h ea d b ol t # 11 8 m m w as he r # 12 m 8 lo ck in g n ut # 34 10 m m p hi lli ps h ...
5 nautilus® pro series elliptical assembly manual reference chart actual size hardware reference chart # 39 3 5m m p an h ea d b ol t # 14 m 10 x 6 5m m a lle n h ea d b ol t # 15 m 10 w as he r #1 6 m 10 l oc ki ng n ut # 25 m 12 x 9 0m m a lle n h ea d b ol t # 37 1 5m m m ac hi ne s cr ew # 19 m ...
6 .Autilus¸%6%64orque3ettings when assembling the ev716 and ev718, please reference and use the torque settings on this page. You must use the correct torque settings to ensure proper assembly and safe usage. 600 kg•cm 200 kg•cm 600 kg•cm 500 kg•cm 500 kg•cm 500 kg•cm 500 kg•cm 500 kg•cm 500 kg•cm 5...
7 nautilus® pro series elliptical assembly manual torque specifications .Autilus¸%6%64orque3ettings when assembling the ev716 and ev718, please reference and use the torque settings on this page. You must use the correct torque settings to ensure proper assembly and safe usage. 600 kg•cm 200 kg•cm 6...
8 assembly process step 1: removing packing & shipping materials 1-1 use box knive to cut the plastic strapping and remove. 1-2 remove the box lid and the styrofoam containing the unit covers (figures 1 & 2). 1-3 remove the outer box cover (figure 3). 1-4 use box knive to cut the shrink wrap on the ...
9 nautilus® pro series elliptical assembly manual assembly process 1-5 cut tape holding styrofoam together and remove the side foot pedal box (figure 5) 1-6 gently angle styrofoam downward and remove (pull down & outwards) from around pod assembly and swing arm (figure 6). 1-7 remove the side pod as...
10 assembly process 2-1 use (4) 20mm allen bolts (ref #1) and (4) 1/2” spring washers (ref #2) to attach the rear frame (#3) to the base unit (#4). Note: tighten bolts in a criss-cross pattern 2-2 attach the plastic flange cover (#5) to the rear frame (#3) using (2) 15mm phillips head screws (ref #6...
11 nautilus® pro series elliptical assembly manual assembly process step 3: attach side rails 3-1 unthread lockout knob (#8), remove (2) phillips head screws (#6), linkage cover (#7) and set aside. 3-2 use (2) 70mm hex head bolts (ref #10), (4) m8 washers (ref #11) and (2) m8 locking nuts (ref #12) ...
1 assembly process step 4: attach support uprights to side rails 4-1 use (6) m10 x 65mm allen head bolts (ref #14), (12) m10 washers (ref #15), and (6) m10 locking nuts (ref #16) to attach the left and right support uprights (#13) to the left and right side rails (#9). Leave hardware only hand-tight...
1 nautilus® pro series elliptical assembly manual step 5: attach linkage cover assembly process 5-1 use (2) 15mm phillips head screws (ref #6) to attach the linkage cover (#7) to the base unit (#4). Reattach the lockout knob (#8). Base unit linkage cover swing arm side rail 6-1 cut wire ties from th...
14 step 7: attach pod assembly assembly process 7-2 feed the left side roller wheel (#22) through the round opening in the front of the pod assembly (#23). The pod assembly may rest on the ground before moving to step 7. Do not yet install right side pod assembly. 7-1 use (5) 15mm phillips head scre...
15 nautilus® pro series elliptical assembly manual assembly process step 8: attach connecting arm pivots 8-1 use (1) m12 x 90mm allen head bolt (ref #25) and (1) m12 locking nut (ref #21) to attach the front connecting arm pivot (#24) and torque to 36 ft/lbs. 8-2 use (1) m12 x 100mm allen head bolt ...
16 step 9: attach upper body arms assembly process 9-1 plug the right and left fingertip control wires (#43) into the wire coming from the base unit. Each handle has its own control wire that must plug into the base unit wire. To avoid damage to the unit, do not allow the arm to hang freely from the...
17 nautilus® pro series elliptical assembly manual assembly process step 10: inspection of assembly 10-1 check torque at all areas highlighted below. For proper torque specifications refer to page 7 and 8 or steps 4, 6, and 8. Note: the pedal to sub pedal arm connection is factory assembled, use #2 ...
18 11-1 use (8) 15mm phillips head screws (ref #6) to install the left and right swing arm covers (ref #3). 11-2 use (8) 10mm phillips head screws (ref #34) to install the left and right rear pivot covers (ref #33). Note: install the center screws first on each side, then the remaining screws. Assem...
19 nautilus® pro series elliptical assembly manual step 12: install pivot covers and end caps assembly process 12-1 use (8) 15mm phillips head screws (ref #6) to install the left and right upright caps (#32). 12-2 use (8) 10mm phillips head screws (ref #34) to install the left and right front pivot ...
0 13-1 (ev-718 only) plug the left hand grip control wire labeled as “left”into the connector on the back of the computer console (#38). 13-2 (ev-718 only) plug the right hand grip control wire labeled as “right” into the connector on the back of the computer console (#38). 13-3 (both models) plug t...
1 nautilus® pro series elliptical assembly manual step 14: install power cord assembly process 14-1 plug power cord into a 110 v, grounded (3-prong) outlet (north american model) or 220 v grounded outlet (ce mark model). Use of extension cords or power strips is not recommended. Machine should now b...
Important contact numbers if you need assistance, please have both the serial number of your machine and the date of purchase available when you contact the appropriate nautilus office listed below. Worldwide customer service • north america office nautilus, inc. World headquarters 16400 s.E. Nautil...
Nautilus® pro series elliptical assembly manual.
Be strong. ™ for more information about our pro series ellipticals or other nautilus ® equipment for your home, visit www.Nautilus.Com. © 2007 nautilus, inc. All rights reserved. Nautilus and the nautilus logo are either registered trademarks or trademarks of nautilus, inc. Nautilus, inc. World head...
