Summary of NS-700
Page 1
Assembly instructions ns-700
Page 2: Ns-700
Ns-700 1 1 rear base frame 1 15823 2 rear top frame 1 15824 3 rear support upright a 1 15828 4 rear support upright b 1 15829 5 rear upright 1 15820 6 top beam 1 15821 7 front upright 1 15819 8 leg extension frame 1 15800 9 main base 1 15817 10 backing plate 3 14105 11 corner plate 1 15805 12 connec...
Page 3: Ns-700
2 complete gym component diagram ns-700 a. Compare the bill of materials to the box contents to insure that all parts are present before installation begins. B. Unpackage parts and place them near the final asssembled location to avoid moving the gym when fully assembled..
Page 4: Ns-700
3 ns-700
Page 5: Step
4 a. Set the rear base frame (1) in a position close to the gym’s final position. B. Attach rear support upright a and b (3) (4) to rear base frame (1) using the hardware shown. Do not tighten hardware. Note: rear support upright a (3) is the longer piece. C. Attach rear top frame (2) to rear suppor...
Page 6: Step
5 a. Attach main base (9) to rear base frame (1) using connecting plate e (16) and the hardware shown. Do not tighten hardware. B. Attach rear upright (5) to rear base frame (1) and rear top frame (2) using connecting plate b (13) and the hardware shown. Do not tighten hardware. C. Attach leg extens...
Page 7: Step
6 step 3 step #3 materials: # component qty 17 pec fly mount 1 18 pec fly cam 2 19 left pec fly arm 1 20 right pec fly arm 1 21 pec fly handle 2 37 pec fly pulley bracket 1 67 plastic cap 4 78 hex bolt - 3/8" x 3 1/4"l 2 79 hex bolt - 3/8" x 3"l 2 87 cap head allen screw 1/4" x 1/2"l with thread loc...
Page 8: Step
7 step 4 step #4 materials: # component qty 22 press arm support assembly 1 23 press arm 1 24 right press arm handle 1 25 left press arm handle 1 26 press arm support shaft 1 27 press arm pivot shaft 1 90 button head allen screw 3/8" x 1"l with thread lock 4 92 5/16" set screw 1/4"l 6 ns-700 a. Atta...
Page 9: Ns-700
Ns-700 8 step 5 step #5 materials: # component qty 28 seat pad 1 29 back pad 1 30 t handle pop pin 2 31 seat adjuster 1 32 seat cross tube 1 33 back pad tube 1 34 back pad adjustment 1 35 back pad adjustment plate 1 74 hex bolt - 1/2" x 3 1/4"l 1 79 hex bolt - 3/8" x 3"l 2 81 hex bolt - 3/8" x 2 1/4...
Page 10: Step
9 step 6 step #6 materials: # component qty 38 locking roller bar 1 39 roller bar 1 40 plastic washer 2 41 pu roller 2 42 8"l foam roller 2 43 pu roller end cap 2 44 round end cap 2 ns-700 a. Slide roller bar (39) through the leg extension tube. Either of the bottom two holes can be used depending o...
Page 11: Ns-700
Ns-700 10 step 7 step #7 materials: # component qty 45 power spring assembly 1 46 front plate 1 47 guide tube 2 48 high/low pulley adjuster 1 49 swivel arm assembly 2 73 hex bolt - 1/2" x 5 1/4"l 2 75 hex bolt - 3/8" x 4 3/4"l 1 79 hex bolt - 3/8" x 3"l 6 80 hex bolt - 3/8" x 2 3/4"l 2 89 button hea...
Page 12: Ns-700
Ns-700 11 step 8 step #8 materials: # component qty 36 pulley bracket 1 50 guide rod holder 2 51 guide rod 4 52 top weight 2 53 selector stem 2 55 weight stack bottom plate 2 56 weight stack bumper 4 66 weight plate 38 86 cap head allen screw 1/4" x 1"l with thread lock 4 94 1/2" flat washer 1 96 1/...
Page 13: Ns-700
Ns-700 12 a. Remove the ball, washer, and u-bracket from one side of cable #2 (70). B. Route cable #2 (70) through the pulleys in the left swivel arm as shown. Continue to route cable around the two pulleys connected to the rear base frame and then around the pulleys located in the rear top frame as...
Page 14: Ns-700
Ns-700 13 step 10 step #10 materials: # component qty 58 4 1/2" pulley 14 61 double floating pulley bracket 2 62 cable retaining bracket 1 68 snap cap 2 69 cable #1 - pull down cable 263.75"l 1 80 hex bolt - 3/8" x 2 3/4"l 4 82 hex bolt - 3/8" x 2"l 8 85 cap head allen screw 3/8" x 3"l with thread l...
Page 15: Ns-700
Ns-700 14 step 10
Page 16: Ns-700
Ns-700 15 step 11 step #11 materials: # component qty 58 4 1/2" pulley 5 72 cable #4 - secondary cable 179.5"l 1 77 hex bolt - 3/8" x 3 1/2"l 1 81 hex bolt - 3/8" x 2 1/4"l 1 82 hex bolt - 3/8" x 2"l 4 83 hex bolt - 3/8" x 1 3/4"l 1 95 3/8" flat washer 14 97 3/8" lock nut 7 101 pulley spacer 1/2"l 2...
Page 17: Ns-700
Ns-700 16 step 12 step #12 materials: # component qty 57 6" pulley 1 58 4 1/2" pulley 4 60 low pulley cover 2 82 hex bolt - 3/8" x 2"l 3 84 hex bolt - 3/8" x 1 1/2"l with thread lock 2 88 button head allen screw 3/8" x 1 3/4"l 2 95 3/8" flat washer 12 97 3/8" lock nut 5 a. Attach two 4 1/2” pulleys ...
Page 18: Ns-700
Ns-700 17 step 13 step #13 materials: # component qty 59 shroud 1 91 button head allen screw 3/8" x 1/2"l with thread lock 4 95 3/8" flat washer 4 111 workout placard 1 a. Attach the shroud (59) to the gym using the hardware shown. B. Adhere the workout placard (111) to the shroud (59) in the positi...
Page 19: Ns-700
Ns-700 18 step 14 attach accessories a. Attach the handles, lat bar, ankle cuff, and ab strap to the cable ends using the cable clips. Lubrication and final check a. Lubricate guide rods and guide tubes using a silicon based lubricant. B. Carefully inspect all cables and insure that they are properl...
Page 20: Ns-700
Ns-700 19 step 15 a. Attach the connecting bench bracket (64) to the rear base frame (1) using the hardware shown. Tighten hardware securely. B. Remove the hardware used on the ns-50 bench that connects the bench frame assembly to the rear stabilizer assembly. Attach the bench connecting plate (65) ...
Page 21: Ns-700
Sub-assembled parts not shown 1b 14159 1 3/4" square end cap 3 2b 14160 pec fly bumper 2 3b 14161 lat bar hook cover 2 4b 14162 2" square end cap 10 5b 14163 1" x 2" rectangular end cap 5 6b 14164 1" round end cap 1 7b 14170 2" x 3" rectangular end cap 1 8b 14168 1 1/2" x 2" rectangular end cap 1 9b...
Page 22: Ns-700
# description qty p/n 4a steel pulley shaft 1 15815 8a small pulley bracket 1 15834 9a left steel pulley 1 15836 10a lever bracket 1 15837 11a right steel pulley 1 15840 14a steel pulley spacer 35 x 26 x 12.8t 1 15843 22a small pulley 1 15853 30a allen screw 3/8" x 1"l w/thread lock 2 15871 31a 6205...
Page 23: Ns-700
605mm (24") 1620mm (63.75"l) # description qty p/n 1a cam mechanism assy cover plate 1 15802 5a leg ext pivot shaft 1 15816 6a seat assembly 1 15818 7a leg extension assembly 1 15825 13a shim washer 2 14385 15a double pulley lock pin w/ 2 c-clips 1 15844 18a plastic cap 2 14187 20a double pulley w/ ...
Page 24: Ns-700
# description qty p/n 2a handle support 2 15811 3a handle support spacer 4 15814 12a power spring rear plate 1 15841 16a ball stop crimp 1 15845 17a handle locking pin w/ 2 c-clips 4 15846 19a power spring cover 1 15849 21a handles 2 15851 23a cushion 4 15854 28a adjustment cable 2 15869 29a power s...
Page 25
The nautilus group 1886 prairie way louisville, colorado 80027 800.499.4322 www.Nautilus.Com.