1. DL manuals
  2. Nav TV
  3. Car Receiver
  4. NTV-KIT585
  5. User Manual

Nav TV NTV-KIT585 User Manual

Manual is about: Navigation interface for FORD vehicles equipped with 8.4” MyTouch

Summary of NTV-KIT585

  • Page 1

    Nng-ford v2 navigation interface for ford vehicles equipped with 8.4” mytouch ntv-kit58 5 3950 nw 120 th ave, coral springs, fl 33065 tel 561-955-9770 fax 561-955-9760 ntv-doc223.

  • Page 2

    Softtouch navigation system 2011-2013 ford escape installation instructions installation performed on escape for reference only. Parts identification page 1 vehicle preparation page 2 2 e g a p s g n i t t e s h c t i w s g n i m m a r g o r p installation page 3 parts identification item qty. Descr...

  • Page 3

    Stop – install at your own risk you must read these warnings and notice before product handling and installation! Product and vehicle application warranty disclaimer warning ! The navigation electronic components are sensitive to electro- static discharge (esd). Do not handle the navigation electron...

  • Page 4

    Warning to avoid dangerous distractions that may lead to an accident, the driver should never operate the system while the vehicle is in motion. Before installing this product, the seller should inform the end-user of proper use and compliance with the proper instructions and all state and federal l...

  • Page 5

    Installation using even pressure, gently remove the upper dashboard trim sliding it out of the way just enough to access the upper radio mounting screws. Remove the two screws from the upper radio mounts. Remove the dashboard trim surrounding the touch screen unit using an automotive trim tool. Tilt...

  • Page 6

    Remove the four screws securing the touch screen unit to the dashboard. Gently turn the touch screen unit towards the driver’s side of the vehicle to easily access the factory wiring harnesses. Gently remove these harnesses (note: the large factory harness includes a locking retainer clip.) gently l...

  • Page 7

    1. To begin, place the lcd assembly face down on a soft surface (esd mat would be best) so as not to scratch the screen. Remove (4x) phillips head screws: 2. Separate the two halves of the assembly by pulling straight up after the screws have been removed. Set the back half of this lcd assembly asid...

  • Page 8

    5. Next, remove (2x) phillips head screws on the top and bottom of the lcd housing: 6. Caref lly separate the metal bracket from the lcd housing, this will expose the touch panel ribbon cable and allow the lcd screen to be separated from the back half of the housing: 7. Ow separate the metal housing...

  • Page 9

    9. Ay the back metal housing down with the circuit board facing up in the orientation shown, and remove (3x) phillips head screws: 10. F om the ntx54-ford kit, gather the sub-board with ribbons attached. Fold the main, bigger ribbon underneath the board like shown below. You should see blue on both ...

  • Page 10

    12. Place the sub-board in the rear lcd housing like shown. This is how the sub-board will be installed into the lcd housing, with the oem ford circuit board beneath the ntx54-ford circuit board. The harnesses from step 11 will be ran through the center square and connected to their prospective conn...

  • Page 11

    14. Replace the factory ford circuit board. The ntx54-ford circuit board needs to be palced on top. Connect the wider ribbon that was tucked underneath the board from step 10 and the touch panel ribbon to the factory ford circuit board like shown below. Use the extended screws provided with the v2 n...

  • Page 12

    15. F ip the modified lcd housing upside down, and place the lcd panel just above the housing. This will make reconnecting the factory ribbons to the new ntx54-ford pcb easier: oem ford lcd n ng-ford pcb oem ford pcb page 11 ntv-doc223.

  • Page 13

    Remove the protective layer from the adhesive backing on the gps speaker and attach it to the interior dashboard frame behind the touch screen. Mount the gps antenna to the top-rear of the vehicle allowing it to attach using its magnetic base. Route the gps antenna extensions harness to the front of...

  • Page 14

    Connect the power harness from the vehicle interface harness to the navigation control module. Connect the speaker interface harness to the navigation control module. Find the threaded end of the gps antenna and connect it to the navigation control module. Connect the vehicle interface harness to th...

  • Page 15

    Apply the included vhb tape to the bottom side of the navigation control module. Attach the navigation control module to the dashboard in the open cavity below the touch screen unit. Attach the vehicle interface harness to the backside of the touch screen unit. Connect the tp-in and lcd-in harnesses...

  • Page 16

    Replace the touch screen unit. Make sure no wires are pinched in the process. Mount the supplied membrane switch to the radio control panel. Replace the dashboard trim pieces. If indoors, start the vehicle and move it outside so that the gps antenna has a clear view of the sky. Press the recently in...

  • Page 17

    Reassembly 1. Reinstall all trim pieces taking special care to ensure harnesses and wiring connections are properly secured. 2. Make sure no harnesses are bent or pinched by trim pieces. 3. Reconnect all disconnected bulbs and check for function. Installation tips t confirm proper cable extension co...

  • Page 18

    Ford audio integration supplementary manual this is a supplementary installation manual for ford navigation system with factory speaker integration. Please carefully refer to the main installation instruction for navigation system. Warranty disclaimer notice! Radio removal, disassembly, installation...

  • Page 19

    Ford audio integration supplementary manual (cont.) components for audio integration: 1. Gps audio box 2. Wiring (fd-audspk-02) 3. Wiring (aud-6pin-01) 4. Main harness (same harness used in main install) 5. Rear-lcd (connected to gps box from main install) steps: 1. Connect both fd-audspk-02 and aud...

  • Page 20

    Igo primo map path setting 1. Press setup ‐> navigate setup 2. Press on the folder icon 3. Select the following path in storage card ‐> cyb_navi.Exe 4. Press home button on the top left corner and press navigation 5. System should able to run into “igo primo”.

  • Page 21: Weak /no Gps Signal?

    Weak /no gps signal? Tips to improve gps antenna signal if vehicle equipped metallized windshield* “gps monitor tools” exit igo map by press shut down button console> setup gps monitor locate the antenna with minimum 5 bars in dark blue or gray bar (always suggest mounting the gps antenna on the roo...

  • Page 22: Proper Gps Antenna Position

    Proper gps antenna position if vehicle equipped *metallized windshield suv/coupe sedan truck (shown as tundra) alternatively, installer might choose to mount antenna inside the headliner or inside vehicle using gps monitor tools (see instruction). However, stay away from the windshield. * windshield...