Navitar motorized zoom systems instruction manual for windows revision b page 1 of 23 2/17/2004 navitar motorized zoom systems instruction manual for windows.
Navitar motorized zoom systems instruction manual for windows revision b page 2 of 23 2/17/2004 navitar motorized zoom lenses generic schematic computer (digital) firewire (digital) frame grabber frame grabber com 1,2 usb 1,2,3 (analog) camera serial usb communication communication zoom focus monito...
Navitar motorized zoom systems instruction manual for windows revision b page 3 of 23 2/17/2004 user's guide windows demonstration application serial and usb connection.
Navitar motorized zoom systems instruction manual for windows revision b page 4 of 23 2/17/2004 table of contents 1 introduction ..................................................................................................5 2 setting up - serial port ...............................................
Navitar motorized zoom systems instruction manual for windows revision b page 5 of 23 2/17/2004 1 introduction/precautions this controller/driver application allows the user to configure and control a 1 or 2 motor zoom/focus system complete with limit sensors. The system may be connected via serial ...
Navitar motorized zoom systems instruction manual for windows revision b page 6 of 23 2/17/2004 following the steps will produce this icon on the desktop. Shortcut to navusb.Exe.Lnk 5 turning the controller on turn on the power switch located on the back of the controller. The controller will activa...
Navitar motorized zoom systems instruction manual for windows revision b page 7 of 23 2/17/2004 this will present a customer setup table similar to the following. Values must be entered before the program will perform. Further explanation of each parameter and suggested initial values may be located...
Navitar motorized zoom systems instruction manual for windows revision b page 8 of 23 2/17/2004 establish the communications, the pc's bell will sound indicating communications failure and the indicator will remain blank. To establish communication manually, click the “mode” pull down menu and selec...
Navitar motorized zoom systems instruction manual for windows revision b page 9 of 23 2/17/2004 selecting the open item from the file pull down menu activates the standard windows open dialog box: the user locates the desired configuration file and confirms selection by clicking the open button. The...
Navitar motorized zoom systems instruction manual for windows revision b page 10 of 23 2/17/2004 8.2 file pull down menu - save selecting the save item from the file pull down menu saves the current motion configuration in the current configuration file. This function is used if a configuration has ...
Navitar motorized zoom systems instruction manual for windows revision b page 11 of 23 2/17/2004 8.5 mode pull down menu - connection this menu item is used to select the desired communications port. The list of available ports is presented by clicking the black down arrow next to com1. Selection is...
Navitar motorized zoom systems instruction manual for windows revision b page 12 of 23 2/17/2004 this configuration is stored within the controller's non-volatile memory and is reloaded into the controller automatically when the controller power is turned on. This configuration should only be edited...
Navitar motorized zoom systems instruction manual for windows revision b page 13 of 23 2/17/2004 8.6.1.2 customer setup - max velocity this value specifies the maximum velocity, in steps per seconds, which the motor may attain after ramp-up in accordance with the desired acceleration curve. 8.6.1.3 ...
Navitar motorized zoom systems instruction manual for windows revision b page 14 of 23 2/17/2004 in the following procedures, “near” is the bottom of travel and “far” is the upper end. “forward” motion is from “near to far” (bottom to top) and reverse is the opposite. Environmental conditions (tempe...
Navitar motorized zoom systems instruction manual for windows revision b page 15 of 23 2/17/2004 note that the motor rotation direction will also change based on the far/near selection. The forward direction is always the direction from home to limit. But the home and limit ends of the travel can be...
Navitar motorized zoom systems instruction manual for windows revision b page 16 of 23 2/17/2004 9 par-focalizing the zoom system. All navitar zoom systems are designed to be parfocal (maintain focus as they change magnification), but they must be setup in a prescribed manner. The rule of thumb is “...
Navitar motorized zoom systems instruction manual for windows revision b page 17 of 23 2/17/2004 10 stop button click the stop button to immediately halt both motors. This function is useful during startup debugging if the motor directions are not defined properly - see customer setup - zero above. ...
Navitar motorized zoom systems instruction manual for windows revision b page 18 of 23 2/17/2004 the position command location is immediate, while the position indicator will track the actual position of the motor. 14 limit indicator / button directly above the motor position indicator is the limit ...
Navitar motorized zoom systems instruction manual for windows revision b page 19 of 23 2/17/2004 17.1 jog minimum value this numerical value controls the number of steps the motor will take in the desired direction if the jog button is clicked once. To change the value, highlight the current value, ...
Navitar motorized zoom systems instruction manual for windows revision b page 20 of 23 2/17/2004 upon sensing a downward motion command and then approach the desired preset. The autorun operation is halted by clearing the autorun checkboxes or by clicking the stop button, which will stop the motors ...
Navitar motorized zoom systems instruction manual for windows revision b page 21 of 23 2/17/2004 rs-232 communication protocol serial data streams. Data to the 2 axis motor controller serial device: serial port configuration: 38400 baud 8 bits no parity 1 stop bit no flow control 7 bytes are written...
Navitar motorized zoom systems instruction manual for windows revision b page 22 of 23 2/17/2004 register definitions: these system registers are intended to be read only. Writes to these registers will not survive a power reset. Reg_sys_productid 0x01 read only -> returns 0x4001 reg_sys_versionhw 0...
Navitar motorized zoom systems instruction manual for windows revision b page 23 of 23 2/17/2004 these user registers are intended for normal operation reg_user_target_1 0x10 motor 1 seek command reg_user_target_2 0x20 motor 2 seek command reg_user_increment_1 0x11 motor 1 delta seek from current re...
