1. DL manuals
  2. Navitar
  3. Projector
  4. VIDEOMATE 2030
  5. Instruction Manual

Navitar VIDEOMATE 2030 Instruction Manual

Manual is about: Video Slide Projector

Summary of VIDEOMATE 2030

  • Page 1

    V ideo m ate 2030/2030 p video slide projector instruction manual the world leader in image quality.

  • Page 2

    2 table of contents 3 product overview 4 safety precautions 5 voltage selection 7 installation 9 slide tray installation 11 lamp/fuse replacement 13 troubleshooting 15 specifications 16 appendix 17 warranty.

  • Page 3

    3 product overview product overview universities, boardrooms, and conventions have the common goal of effective information communication. Today’s individual is continually being bombarded by sophisticated media presentation. To compete effectively for his attention (and retention) one must utilize ...

  • Page 4

    4 7 safety precautions safety precautions for safety, before connecting the projector to the main, ensure that the voltage selector is set to your main voltage and the required fuse is fitted. An incorrectly adjusted main voltage can damage the projector. To prevent damage to equipment and operating...

  • Page 5

    5 voltage selection voltage selection check voltage setting. The navitar videomate will be exported throughout the world to countries with differing mains voltages. The projectors are already set during manufacture to a fixed main voltage. 100-200v mains: shipments to countries with 100 or 200v main...

  • Page 6

    6 voltage selector tray positioning index mark lock ring alignment mark fuse holder voltage selection.

  • Page 7

    7 installation installation before installing please review precautions. For those users familiar with both the operation of 35mm slide projector and their own video displays, the following is an abbreviated start-up procedure. 1. Check the voltage setting before powering on. Make sure that the sett...

  • Page 8

    8 installation 9. To shut down the system, hold down the select bar and rotate the slide tray to the “0” index position. Set the power switch to “off”. 10. For instructions regarding setting up slide tray changing lamps, etc., refer to the appropriate section of the manual. Iris knob zoom knob selec...

  • Page 9

    9 slide tray installation slide tray set-up this system was designed to permit usage of prepared presentations without reorientation of the slides in the tray. Your new navitar videomate will accept kodak ektapro 80, kodak ektagraphic 80 for holding 80 slides with a maximum slide mount thickness of ...

  • Page 10

    10 slide tray installation slide tray removal to remove the tray from the projector without losing slides: 1. Hold the selector bar down and rotate the tray back to the zero index position. 2. Lift the tray at a point opposite the index mark. Slide tray jam the tray may jam if a damaged slide is cau...

  • Page 11

    11 lamps/fuse replacement lamps the videomate will function with either of the following 82 volt or 85 watt lamps. One provides a higher color temperature, with the other exhibits a much longer life. Do not use 82 volt, 25-300 watt slide projection lamps or your equipment will suffer severe damage. ...

  • Page 12

    12 4. Reverse the procedure to insert a new lamp (make sure the new lamp is properly seated). 5. Lock the new lamp in place with wire bail. Fuses always switch off the projector and unplug the main lead before replacing a fuse. Avoid the risk of fire, replace only with a fuse of same type and rating...

  • Page 13

    13 troubleshooting troubleshooting symptom #1: after switching on, projector is not operable. Possible cause: 1. All equipment not “powered up”. Check outlets and individual unit (monitor, video projector, etc.). 2. Check input voltage selector. 3. Lamp blown. Look in film gate for “light on conditi...

  • Page 14

    14 symptom #4 image too dark or too light. Possible cause: 1. Illumination level inadequate. Set knob “i” as required. 2. Monitor not adjusted properly. Symptom #5 image not sharp. Possible cause: 1. Adjust focus knob. 2. Illumination level is too high or too low. Adjust illumination knob. 3. Monito...

  • Page 15

    15 s n o i t a c i f i c e p s a r e m a c e c i v e d p u - k c i p d c c r e f s n a r t e n il r e t n i " 2 / 1 t n u o c l e x i p ) v ( 2 8 5 x ) h ( 2 5 7 r e t l i f r o l o c c i a s o m r o l o c y r a t n e m il p m o c m e t s y s l a n g i s ) e l b a l i a v a c s t n ( d r a d n a t s...

  • Page 16

    16 appendix appendix due to transportation, the image position might shift from the factory setting. To correct this shift: 1. Remove the two plugs as shown in the figure below: 2. Using the phillips screw driver, rotate screw #1 to adjust the vertical position and screw #2 to adjust the horizontal ...

  • Page 17

    17 warranty 1 year parts /1 year labor this product is warranted to be free from defects in material and workmanship for a period of five years from the date of invoice to the original purchaser. If during the warranty period the product is found to be defective, it will be repaired or replaced at t...

  • Page 18

    18 navitar, inc. 200 commerce drive rochester, ny 14623 (716) 359-4000 phone (716) 359-4999 fax internet http://navitar.Com/ e-mail info@navitar.Com.