1. DL manuals
  2. Navitar
  3. Projector
  4. VideoMate 2250
  5. User Manual

Navitar VideoMate 2250 User Manual

Manual is about: Navitar VideoMate 2250: User Guide

Summary of VideoMate 2250

  • Page 1

    V ideo m ate 2250/2250 p video slide projector instruction manual the world leader in image quality.

  • Page 2

    Ektapro and kodak are both trademarks of the eastman kodak company. Ektapro manual drawings used with the permission of eastman kodak company. Videomate and navitar are both trademarks of navitar, inc..

  • Page 3

    3 table of contents 4 introduction to the videomate 6 system diagrams 7 safety precautions 8 voltage selection 9 quick start 10 installation 11 slide tray 14 operation 16 lamps and fuses 18 features & functions 21 troubleshooting 22 specifications 23 warranty.

  • Page 4

    4 introduction to the videomate videomate slide-to-video systems today’s sophisticated audiences expect high quality visual aids in the presentations they attend. Since a picture is “worth a thousand words,” as they say, there is no better way to increase the effectiveness of a presen- tation than t...

  • Page 5

    5 introduction to the videomate the built-in motorized zoom lens allows the 2250 to zoom in on slides for increased magnification or zoom out to view entire vertical slides. A unique “stand-by” mode, allows the projector to be powered off and back on again without the normal return of the slide tray...

  • Page 6

    6 systems diagrams top view rear view.

  • Page 7

    7 safety precautions safety precautions to prevent damage to the equipment and operating personnel, please observe the following precautions: set the projector voltage switch to the proper wall outlet voltage for your country (usa = 120v and uk = 240v). Make sure that the voltage source contains a s...

  • Page 8

    8 voltage selection check voltage setting the videomate 2250 is exported throughout the world to countries with different mains voltages. The projectors are set to a fixed mains voltage at the factory. 120v mains shipments to countries with 120v mains will be equipped with a 4a fuse. 220, 230 or 240...

  • Page 9

    9 quick start quick start if you are familiar with both the operation of a 35mm slide projector and your video display, you may follow an abbreviated start-up procedure. Before starting, review the precautions on page 5. To “quick start” the videomate 2250, proceed as follows: 1. Check the voltage s...

  • Page 10

    10 installation installation before starting, review the precautions on page 5. To install the videomate 2250, proceed as follows: 1. Check the voltage setting before powering on. Make sure that the setting above the power cord is correct for your voltage. Also, check the fuse behind the voltage set...

  • Page 11

    11 slide tray loading and installing the slide tray the videomate 2250 will accept all 80 and 140 carousel, ektagraphic and sav slide trays. We recommend the 80 slide tray for maximum reliability. 1. Check that the base plate of the slide tray is locked into the zero position and cannot be rotated. ...

  • Page 12

    12 heads to move the internal unit in a sideways motion. Retighten the four screws. The two screws marked “b” provide both vertical and rotational image movements. Turning one screw will tip, or rotate, the image, while turning both screws will move the image in a vertical direction. Caution do not ...

  • Page 13

    13 slide tray changing the slide tray always lift the slide tray off when it is in the zero position. The zero positioning lights up when the slide tray trans- port ring is in the zero position. Moving the tray into the zero position using the slide change buttons on your projector or remote control...

  • Page 14

    14 operation understanding which video output is best for you composite video standard video image quality which is fine for showing pictures of objects on a tv monitor. Y/c (also know as s-video and s-vhs) improved resolution that is less grainy due to the elimina- tion of dot crawl. Better for pre...

  • Page 15

    15 adjusting the horizontal phase 1. Set the arrow “ → “ to h phase by pushing the function up, function down buttons. 2. Adjust the horizontal phase by pushing the data up, data down buttons. The values range from -99 to 99, data up will increase the setting towards 99 and data down will decrease i...

  • Page 16

    16 lamps and fuses replacing the lamp use a general electric 787 (6 volt, 10 watt) lamp or its equivalent (navitar part #9-12126). 1. Turn the power switch of off and allow the lamp to cool before handling. 2. Loosen the cover lock screw two turns. Rotate the cover counterclockwise and remove. 3. Re...

  • Page 17

    17 lamps and fuses replacing secondary circuit fuses please note that these fuses are different! Two secondary fuses protect the projector against damage caused by overloading the projector’s remote socket. 1. Turn the fuse carrier counterclockwise with a screw- driver or coin. 2. Replace the defect...

  • Page 18

    18 features and functions dissolve operation the videomate 2250 is fully equipped for dissolve operation and is fully equipped for dissolve operation and is fully compatible with external dissolve. Control sys- tems already in existence. Remote control in the past, most projectors were controlled by...

  • Page 19

    19 electrical system power voltage ac only! Different power voltages are adjustable via the removable fuse link (120, 220, 230, 240v). Frequency 50/60hz performance approximately 100va fuses primary circuit: 1x2a slow blow for 220, 230 and 240v or 1x4a slow blow for 120v. Secondary circuit: 1x2a/26v...

  • Page 20

    20 8-pin standard projector socket pin 1: 12 vdc pin 2: gnd pin 3: signal 1 (lsb) pin 4: signal 2 pin 5: signal 3 pin 6: signal 4 pin 7: signal 5 (msb) pin 7: interrupt control system p-bus-in 9-pin sub-d female connector (v.24/v.28 standard interface). P-bus-out 9-pin sub-d male connector (v.24/v.2...

  • Page 21

    21 troubleshooting m o t p m y s y d e m e r / e s u a c s i r o t c e j o r p e h t r e tf a e l b a r e p o t o n e h t g n i h c ti w s . N o r e w o p e c a l p e r d n a s e s u f e h t k c e h c ? N w o l b ) y r a d n o c e s r o y r a m ir p ( e s u f a s i . Y r a s s e c e n fi m e h t . G...

  • Page 22

    22 specifications camera pick-up device 1/3” interline transfer pixel count 768(h) x 494(v); 754(h) x 582(v) (pal) color filter complimentary color mosaic signal system ntsc standard (pal available) horizontal 460 tv lines (450 pal) resolution sensitivity f1.2 (4.5 lux), 3200k° color temperature gen...

  • Page 23

    23 warranty 5 year parts /5 year labor this product is warranted to be free from defects in material and workmanship for a period of five years from the date of invoice to the original purchaser. If during the warranty period the product is found to be defective, it will be repaired or replaced at t...

  • Page 24

    Navitar, inc. 200 commerce drive rochester, ny 14623 (716) 359-4000 phone (716) 359-4999 fax internet http://navitar.Com/ e-mail info@navitar.Com.