Navman DDR MiVue 800 User Manual
User Manual
DDR MiVue 800
DDR MiVue
Series
1
5
2
6
3
7
4
8
9
Getting to know your dash cam
Note: The screenshots and other presentations shown in this manual may differ from the ones generated by the
actual product.
l
MiVue rear camera
1
Mounting pad
2
Camera lens
3
Adjustment bolt
4
Micro-USB connector
l
MiVue dash cam
1
Power button
2
Microphone
3
Mini-USB connector
4
System indicator
5
Event button
6
LCD screen
7
Function keys
8
Parking indicator
9
Speaker
10
Camera lens
11
Memory card slot
1
2
3
4
5
6
8 9
10
11
7
1
2
3
4
Power button
l
Press and hold for 2 seconds to manually turn the dash cam on and off.
l
When the dash cam is turned on, press to switch the LCD screen on and off.
Function keys
The device provides four function keys to control the corresponding icons displayed on the LCD screen. The keys'
functions may vary on different screens.
Opens the Menu screen
Enters Parking mode
Takes a photo
(Recording screen)
3. When adjusting the angle of mounting, make sure that the camera’s view is parallel with the level ground and the
ground/sky ratio is close to 6/4.
4. Connect the vehicle power adapter to the cigarette lighter. Route the cables through the top ceiling and the A-pillar
so that it does not interfere with driving. Make sure that the cable installation does not interfere with the vehicle's
airbags or other safety features.
Vehicle power adapter
Y-cable MiVue dash cam
Rear camera cable
MiVue rear camera
Note:
l
If you only use the dash cam (without connecting the rear camera) in your vehicle, simply connect the vehicle
power adapter to the dash cam and then plug it to the cigarette lighter.
l
The installation illustrations are for your reference only. The placement of the devices and cables may vary
depending on the vehicle model. If you encounter any problems during installation, contact a skilled installer (such
as the service personnel of the vehicle) for assistance.
Using your dash cam in a vehicle
Note:
l
To ensure the highest quality recordings, you are advised to place the dash cam near the rear-view mirror.
l
Select an appropriate location for mounting the device in a vehicle. Never place the device where the driver’s
field of vision is blocked.
l
If the car’s windscreen is tinted with a reflective coating, it may be athermic and impact the GPS reception. In this
instance, please mount your device where there is a “clear area.”
l
The system will automatically calibrate the G sensor of the device during start-up. To avoid G sensor malfunction,
always turn the device on AFTER you mount it in the vehicle properly.
l
The Mivue dash cam is designed to stay connected with the vehicle power adapter to ensure optimal
performance. The battery is designed as a backup power source for short term use only in the event when the
vehicles power system is cut out during an incident so the dash cam can save the last recording. It is not to be
used as sole source of power for prolonged periods.
Make sure that your car is parked on level ground. Follow the instructions to securely mount your dash cam and rear
camera into a vehicle.
1. Mount the dash cam.
2. Mount the rear camera.
Moves to the next option
Acts as the ENTER button
Moves to the previous option
Acts as the BACK button
(Menu screen)
Once you connect the rear camera and start recording, the screen displays the PIP (picture-in-picture) mode. You can
switch the front and rear camera images by pressing
.
System icons
Various system icons on the status bar at the top of the screen provide the status information of your device. The
displayed icons will vary depending on your device model and state.
1
Recording indicator
2
Time display
3
Microphone status
4
GPS signal
5
Power status
6
Current speed
6
1
2
3 4 5
System indicator
The system indicator glows in green when the dash cam is powered. When powered, the indicator flashes in green and
amber alternately while the recording is in progress.
Inserting a memory card
You must insert a memory card (not supplied) before you can start recording. The
dash cam supports Class 10 memory cards with 8 GB – 128 GB capacity.
Hold the card by the edges and gently insert it into the slot as shown in the
illustration. To remove a card, gently push the top edge of the card inwards to
release it and pull it out of the slot.
Formatting a card
If you need to format a memory card (all data will be erased), press
and select
Format.
Note:
l
DO NOT apply pressure to the centre of the memory card.
l
Navman does not guarantee the product’s compatibility with memory cards from all manufacturers.
l
Before you start recording, please format the memory card to avoid malfunction caused by files not created by
the dash cam.
l
You are advised to turn the device off before removing the memory card.
Operating basics
Turning the dash cam on
Complete the installation according to the instructions in the “Using your dash cam in a vehicle” section. Once the
vehicle engine is started, the dash cam automatically turns on.
Occasionally you may need to perform a hardware reset when the dash
cam stops responding or if it appears to be “frozen” or unresponsive. If you
cannot turn the dash cam off by using the Power button, insert a small rod
(such as a straightened paper clip) into the Shutdown button to shut down
the dash cam.
Setting the date and time
To make sure that the date and time of your recordings are correct, check the settings before you begin recording.
1. Press
to access the Settings Menu.
2. Select
System > Date / Time and press
.
3. Select
Use GPS time or Manual:
l
When you select
Use GPS time, the system will set date and time according to the GPS location.
l
When you select
Manual, the system will display the date and time setting screen.
Use
/
to adjust the value of the selected field; press
and repeat the step until all fields
have been changed. When completed, press
.
Recording in driving mode
Continuous recording
By default, the system will automatically begin with continuous recording in a few seconds after start-up. The
recording may be divided into several video clips; recording will not stop between video clips. When your memory
card fills up with continuous recordings in the "Video" category, it will automatically record over the oldest existing
files in this category.
When continuous recording is in progress, you can manually stop recording by pressing
. Press
to return
to the recording screen; the system will start continuous recording automatically.
The continuous recordings can be found in the “Video” category for file playback.
Event recording
By default, if an event happens such as a sudden impact, high speed driving, an aggressive turn or an accidental crash
during continuous recording, the G sensor will prompt the dash cam to start recording the event.
The dash cam will automatically save any video 10 seconds prior to the activation of the sensor and continue to
record for another 10 seconds post activation in a 20 second video file which will be saved to the "Event" category
on your microSD card. However, if another event is triggered during this time, it will continue to record for another
10 seconds and can trigger more events to continuing recording a further 10 seconds up to a 1 minute video file.
Recordings stored in the "Event" category are separate to the "Video" category.
Note: You can change the sensitivity level of the G sensor by selecting
> Video Recording > G-Sensor
Sensitivity.
If you want to manually start an event recording while continuous recording is in progress, press the Event button on the
device.
The event recordings can be found in the “Event” category for file playback.
Recording in Parking mode
Your dash cam supports the parking recording function. Your dash cam will require an additional power source (such as
an uninterruptible power cable or Smartbox accessory which is sold separately. Visit www.navman.com.au to purchase
this accessory.) to record the video during Parking mode. The dash cam cannot operate the Parking Mode feature on the
internal battery power.
The Parking mode function is disabled by default. You can enable the function by selecting
> Parking Mode
> Detection > On. Before enabling Park mode, please check your device memory storage allocation. Go to
>
System > Storage Allocation to set a proper allocation for parking recording. Changing the allocation will erase the
memory card, so save any videos or photos to your computer first.
When the Parking mode detection is enabled, the system will enter Parking mode when you:
l
Disconnect the device's power (when the vehicle engine is stopped or the power cable is disconnected) or when the
car stops moving for about 5 minutes.
Note: The feature is triggered by the G sensor of the device. You can change the configuration by selecting
> Parking Mode > Auto Entry.
l
Press
to manually start Parking mode while continuous recording is in progress.
To stop Parking mode and resume continuous recording, press
. If movements are detected and recorded during
Parking mode, you will be asked to play the video when you stop Parking mode.
The parking recordings can be found in the “Parking” category for file playback.
Camera mode
The dash cam allows you to take a photo. The photos can be found in the “Photo” category for file playback.
l
If the recording is in progress, press
to take a photo. (This function is not available when the rear camera is
connected.)
l
Press
> Camera >
.
Playback mode
To select a video or photo for playback:
1. Press
> File Playback.
2. Select the desired type:
Video, Event, Parking or Photo.
3. Press
/
to select the desired file from the list and then press
to start playback.
4. During playback, you can:
l
While playing videos, press
/
to play the previous/next video.
l
While viewing photos, press
/
to display the previous/next photo.
l
Press
to return to the list.
l
Press
to display the pop-up menu to select:
l
Play/Pause: Starts or pauses the playback.
l
Play rear video: (For selected models only) The "D" icon displayed on the thumbnail on the playlist
indicates that the video comes with a corresponding rear video. While playing the front video, you can use
this option to switch to the rear video.
l
Move to Event: Moves the file to the “Event” category.
l
Delete: Deletes the file.
Note: The video files recorded by the front and rear cameras will be saved separately in the corresponding
folders of the memory card. If you move or delete a front video, its corresponding rear video will be
processed synchronously.
System settings
To customise the system settings, press
.
l
File Playback
Plays the recorded videos and photos.
l
Camera
Press to enter Camera mode.
l
Sound Recording
Sets if you want to include sounds in the recordings. The default setting is
On.
l
Driving Safety
The dash cam provides advanced driving safety functions to make your driving safer.
l
Headlight Reminder: The system will remind you to turn the lights on when you are driving after dark.
l
Driver Fatigue Alert: The system will remind you to take a break after long-distance driving 2 hours (default)
/
3 hours / 4 hours.
l
Parking mode
Allows you to change the settings of Parking mode. The available settings include:
l
Detection: When enabled, the dash cam will automatically start recording when it detects movements or if an
event happens in Parking mode.
l
Detection Method: The options are Only G-sensor, Only Motion and Both Motion & G-sensor.
l
Auto Entry: Sets the mode (Low, Medium, High or Manual) for the system to enter Parking mode
automatically.
l
Motion Detection: The options are Low, Medium and High.
l
G-Sensor Sensitivity: Sets the sensitivity level (Low, Medium or High) of the G sensor that allows
automatic triggering of the parking recording when the dash cam is in Parking mode.
l
LED Indicator: The options are On and Off.
l
Video Recording
Changes the settings of recording, including:
l
Video Clip Length: Sets the length of each video clip for a continuous recording (1 min, 3 min or 5 min).
l
WDR: Enables the WDR (Wide Dynamic Range) function to improve the dash cam's image quality under high-
contrast lighting conditions.
l
EV: Sets the proper exposure level (-1 – +1) to adjust the brightness of the image. The default setting is 0.
l
G-Sensor Sensitivity: Sets the sensitivity level (6 levels, from Low to High) of the G sensor that allows
automatic triggering of the event recording while continuous recording is in progress.
l
Stamps: Sets the information (Coordinates or G-Sensor) that will be displayed on the recorded video.
l
Speed Stamp: Displays the driving speed on the recorded video.
l
Text Stamp: Displays the customised information on the recorded video.
l
System
Allows you to change the system settings of the device.
l
Satellites: Displays the status of GPS/GLONASS signal reception. You can press
and then select
GPS
or
GLONASS for better signal reception if the need arises. (GPS is recommended for use in Australia and
New Zealand regions.)
l
Date/Time: Sets the system date and time.
l
System Sound: Enables or disables system notification sounds.
l
Volume: Adjusts the volume level.
l
LCD Standby: Selects Always On to keep the LCD on; or sets the timer for the LCD to turn off
automatically (
10 sec, 1 min or 3 min) after recording starts. Selecting HUD will turn off the LCD (in
specified time) but still display the time and speed information.
l
Language: Sets the language.
l
Distance Unit: Sets the preferred distance unit.
l
Storage Allocation: The system provides 3 default memory configurations to store the videos (including
continuous recordings and event recordings) and photos. Select the proper configuration based on your
usage.
l
Restore to Defaults: Restores system settings to factory defaults.
l
Version: Displays the software information.
l
Format
Formats a memory card. (All data will be erased.)
Revision: R00
(5/2017)
Trademarks
All brand and product names are trademarks or registered trademarks of their respective companies.
Disclaimer
Specifications and documents are subject to change without notice. Navman does not warrant this document
is error-free. Navman assumes no liability for damage incurred directly or indirectly from errors, omissions, or
discrepancies between the device and the documents.
Notes
Not all models are available in all regions.
Depending upon the specific model purchased, the colour and look of your device and accessories may not exactly
match the graphics shown in this document.
Regulatory information
For regulatory identification purposes, Navman DDR MiVue™ 800 is assigned
a model number of N489. Marking labels located on the exterior of your
device indicate the regulations that your model complies with. Please check
the marking labels on your device and refer to the corresponding statements
in this section. Some notices apply to specific models only. The user needs
to switch off the device when exposed to areas with potentially explosive
atmospheres such as petrol stations, chemical storage depots and blasting
operations.
5 6 1 5 N 4 8 9 0 0 2 8 R 0 0