1. DL manuals
  2. NCR
  3. Server
  4. NCR S16
  5. Installation Manual

NCR NCR S16 Installation Manual

Summary of NCR S16

  • Page 1

    Bst0-2142-0100 12/97 ncr s16 minitower server installing network operating system release 3.

  • Page 2

    The product described in this book is a licensed product of ncr corporation. Brand and product names appearing in this manual are for identification purposes only and may be registered trademarks or trademarks of their respective companies. It is the policy of ncr corporation (ncr) to improve produc...

  • Page 3: Contents

    Ncr s16 minitower server installing network operating system iii contents preface about this book............................................................................................................ I who should read this book .....................................................................

  • Page 4

    Contents iv contents selecting network protocols .......................................................................................4-8 providing additional setup information .....................................................................4-9 completing the installation........................

  • Page 5

    Contents ncr s16 minitower server installing network operating system v chapter 8 installing sco unix overview .......................................................................................................................... 8-2 installation overview............................................

  • Page 6

    Contents vi contents restarting the installation......................................................................................... 11-5 performing a default installation..................................................................................... 11-6 booting from the installation med...

  • Page 7: Preface

    Ncr s16 minitower server installing network operating system i preface about this book this book provides detailed instructions about the installation and configuration of network operating systems on your server. The installation information included in this manual is current as of the date of publ...

  • Page 8: Related Publications

    Preface ii preface conventions used in this book the following conventions are used in this book: f1 a letter, number, symbol, or word in this font represents a key on your keyboard. For example, the instruction “press f1” means press the key labeled “f1” on your keyboard. Enter this represents the ...

  • Page 9: Chapter 1

    Ncr s16 minitower server installing network operating system 1-1 chapter 1 installation overview.

  • Page 10: Overview

    Overview 1-2 installation overview overview thank you for selecting an ncr server. This book is designed to get you started installing and configuring your system. The following information is included: • a summary of the setup process • bios setup procedure • adaptec bios scsiselect utility procedu...

  • Page 11

    Documentation needed for setup ncr s16 minitower server installing network operating system 1-3 documentation needed for setup you should have the following information to perform the setup: • this book, ncr s16 minitower server installing network operating system (bst0-2142-01) • ncr s16 minitower ...

  • Page 12: Where to Start

    Where to start 1-4 installation overview where to start after you have installed the hardware, follow these steps to install a network operating system on your system. Step what to do how to do it where to find information 1 confirm the cmos settings and configure pci adapters follow the instruction...

  • Page 13: Chapter 2

    Ncr s16 minitower server installing network operating system 2-1 chapter 2 confirming the cmos settings and configuring pci adapters.

  • Page 14: Overview

    Overview 2-2 confirming the cmos settings and configuring pci adapters overview before installing a network operating system on your server, you must confirm the cmos settings using bios setup and configure the pci adapter settings. This chapter describes the procedures..

  • Page 15: Confirming The Cmos Settings

    Confirming the cmos settings ncr s16 minitower server installing network operating system 2-3 confirming the cmos settings this section discusses the bios system setup procedure. To configure system settings in the bios setup utility, follow these steps: 1. Turn on power to the system. Observe that ...

  • Page 16

    Confirming the cmos settings 2-4 confirming the cmos settings and configuring pci adapters ide drive 3 (xxx mb) none on board ide disabled 6. Press esc to return to the main menu in bios setup. 7. Select advanced system configuration. Page 1 - verify that the parameters are set as follows: e0000h - ...

  • Page 17

    Confirming the cmos settings ncr s16 minitower server installing network operating system 2-5 on board communication ports serial port 1 base address 3f8h serial port 2 base address 2f8h parallel port base address parallel 1 (3bch) operation mode stndrd pp (spp) mode ecp dma channel - on board ps/2 ...

  • Page 18: Configuring Pci Adapters

    Configuring pci adapters 2-6 confirming the cmos settings and configuring pci adapters configuring pci adapters to configure pci adapters, follow these steps: 1. Select pci system configuration from the main menu in bios setup. Figure 2-1. Pci system configuration screen pci system configuration pci...

  • Page 19

    Configuring pci adapters ncr s16 minitower server installing network operating system 2-7 3. After you have made your settings, press esc to return to the main menu in the bios setup. 4. Press esc again. Select yes to save your system and pci adapter settings and to reboot the system..

  • Page 20

    Configuring pci adapters 2-8 confirming the cmos settings and configuring pci adapters.

  • Page 21: Chapter 3

    Ncr s16 minitower server installing network operating system 3-1 chapter 3 confirming the scsi adapter settings.

  • Page 22: Overview

    Overview 3-2 confirming the scsi adapter settings overview before installing a network operating system on your server, you must confirm the adapter settings, using the adaptec bios scsiselect utility. This chapter describes the procedure..

  • Page 23

    Configuring the scsi adapters ncr s16 minitower server installing network operating system 3-3 configuring the scsi adapters to configure the scsi adapters, if connected to an adaptec scsi adapter, follow these steps: 1. Press ctrl + a when the following displays: adaptec aic-7880 ultra/ultra w bios...

  • Page 24

    Configuring the scsi adapters 3-4 confirming the scsi adapter settings send start unit command yes 5. Press esc to return to previous menu. 6. Select advanced configuration options and set the parameters as follows: host adapter bios (config util...) enabled support removable disks... Boot only ** e...

  • Page 25: Chapter 4

    Ncr s16 minitower server installing network operating system 4-1 chapter 4 installing microsoft windows nt server 3.51.

  • Page 26: Overview

    Overview 4-2 installing microsoft windows nt server 3.51 overview this chapter discusses installing microsoft windows nt server 3.51 on your server. To install windows nt server 3.51 on your server, follow these steps: • confirm the cmos settings using bios setup - see chapter 2 • confirm the adapte...

  • Page 27: Nt Server 3.51

    Performing a full installation of windows nt server 3.51 ncr s16 minitower server installing network operating system 4-3 performing a full installation of windows nt server 3.51 to install windows nt server 3.51, follow these steps: 1. Insert the windows nt server setup boot disk into the flex disk...

  • Page 28: Installing From The Cd-Rom

    Performing a full installation of windows nt server 3.51 4-4 installing microsoft windows nt server 3.51 inserting the windows nt server setup disk 3 when prompted to insert the windows nt server setup disk 3, follow these steps: 1. Insert the disk, and press enter. 2. Verify that the bottom of the ...

  • Page 29

    Performing a full installation of windows nt server 3.51 ncr s16 minitower server installing network operating system 4-5 1. If you are certain that there is no valuable data on the disk, press c to continue. Note: all of the data which was formerly on the disk will be erased when you select this op...

  • Page 30

    Performing a full installation of windows nt server 3.51 4-6 installing microsoft windows nt server 3.51 4. Next, select the file system you want to use. If the disk was previously formatted as fat, you may be prompted to convert it to ntfs. Otherwise, you are prompted to format the disk as fat or n...

  • Page 31

    Performing a full installation of windows nt server 3.51 ncr s16 minitower server installing network operating system 4-7 completing user and server information continue the installation by completing user and server specific information. Follow these steps: 1. You are prompted for your name and com...

  • Page 32: Selecting Network Protocols

    Performing a full installation of windows nt server 3.51 4-8 installing microsoft windows nt server 3.51 10. If you selected install only components i select, then you are prompted to change the components. When done, press enter. 11. If you want to set up a printer, select the name of the printer, ...

  • Page 33

    Performing a full installation of windows nt server 3.51 ncr s16 minitower server installing network operating system 4-9 you may also select to enter the ip addresses of your primary and secondary wins server. When you have finished, select ok. 4. If you do not fill in a wins address in the precedi...

  • Page 34: Completing The Installation

    Performing a full installation of windows nt server 3.51 4-10 installing microsoft windows nt server 3.51 4. The installation program prompts you to enter your current date, time, and time zone. After each item has been entered, select ok. 5. You may be prompted to identify various executable files ...

  • Page 35

    Performing a full installation of windows nt server 3.51 ncr s16 minitower server installing network operating system 4-11 2. The system reboots, and if you selected the ntfs file system for any volume on your system, the file system is automatically converted to ntfs at this time. The installation ...

  • Page 36

    Performing a full installation of windows nt server 3.51 4-12 installing microsoft windows nt server 3.51.

  • Page 37: Chapter 5

    Ncr s16 minitower server installing network operating system 5-1 chapter 5 installing microsoft windows nt server 4.0

  • Page 38: Overview

    Overview 5-2 installing microsoft windows nt server 4.0 overview this chapter describes the installation procedure for microsoft windows nt server 4.0 on your server. The first part of the chapter discusses what you need to do to your system if microsoft windows nt server was pre-loaded at the facto...

  • Page 39: Pre-Loaded Installation

    Pre-loaded installation ncr s16 minitower server installing network operating system 5-3 pre-loaded installation if your system was pre-loaded at the factory with microsoft windows nt server, you need to complete the installation of the system by providing several site-specific configuration items. ...

  • Page 40

    Pre-loaded installation 5-4 installing microsoft windows nt server 4.0 depending on the version of ncr server manager loaded on your server, you may be asked about the type of system you are installing. Answer the questions appropriately for your system and site configuration. 2. Enter your name and...

  • Page 41

    Pre-loaded installation ncr s16 minitower server installing network operating system 5-5 4. You are prompted to set the time, date and time zone on the system. When you are satisfied that the time is correct, select ok. After a short time, your system reboots. 5. Sign onto the system, using the admi...

  • Page 42: Non-Pre-Load Installation

    Non-pre-load installation 5-6 installing microsoft windows nt server 4.0 non-pre-load installation if windows nt server was not pre-loaded on your server at the factory, use this section to prepare your system and install the software. To install windows nt server 4.0 on your server, follow these st...

  • Page 43: Nt Server 4.0

    Performing a full installation of windows nt server 4.0 ncr s16 minitower server installing network operating system 5-7 performing a full installation of windows nt server 4.0 to install windows nt server 4.0, follow these steps: 1. Insert the windows nt server setup boot disk into the flex disk dr...

  • Page 44: Preparing The Hard Disk

    Performing a full installation of windows nt server 4.0 5-8 installing microsoft windows nt server 4.0 8. When prompted to validate your system settings, make any necessary changes and press enter to continue. Preparing the hard disk if a message displays indicating that the setup procedure has dete...

  • Page 45

    Performing a full installation of windows nt server 4.0 ncr s16 minitower server installing network operating system 5-9 – the first system drive is larger than 1024 mb. – there are no partitions already defined on the system drives. • in addition, after the 1024 mb partition has been created during...

  • Page 46: Installing The Network

    Performing a full installation of windows nt server 4.0 5-10 installing microsoft windows nt server 4.0 completing user and server information continue the installation by completing user and server specific information. Follow these steps: 1. When the windows nt setup screen displays, press enter. ...

  • Page 47: Selecting Network Protocols

    Performing a full installation of windows nt server 4.0 ncr s16 minitower server installing network operating system 5-11 3. When prompted to have the setup utility search for your network adapters, choose select from list and have disk. 4. Insert your network interface board driver disk. Select the...

  • Page 48

    Performing a full installation of windows nt server 4.0 5-12 installing microsoft windows nt server 4.0 9. If you previously indicated that you want this system to be a server, you are prompted to indicate the name of the domain or workgroup this system will join. Entering additional setup informati...

  • Page 49: Chapter 6

    Ncr s16 minitower server installing network operating system 6-1 chapter 6 installing windows nt server 4.0 enterprise edition.

  • Page 50: Overview

    Overview 6-2 installing windows nt server 4.0 enterprise edition overview this chapter describes the installation of microsoft windows nt server 4.0 enterprise edition. The installation of nt server 4.0 enterprise edition consists of the following: • installing nt server 4.0 enterprise edition • ins...

  • Page 51: Install Service Pack 3

    Install service pack 3 ncr s16 minitower server installing network operating system 6-3 install service pack 3 after installing nt 4.0 by inserting the nt 4.0 ee cd and double clicking on the setup.Exe application and following the instructions on the screen to install the software, you are ready to...

  • Page 52: Enable 4 Gb Support

    Enable 4 gb support 6-4 installing windows nt server 4.0 enterprise edition enable 4 gb support after installing nt server 4.0 and installing service pack 3, you must update the c:\boot.Ini file to enable 4gb support. To update the c:\boot.Ini file, follow these steps: 1. The boot.Ini file is a hidd...

  • Page 53

    Enable 4 gb support ncr s16 minitower server installing network operating system 6-5 boot.Ini file after modification example for example, after modification after modification, your boot.Ini file might look like the following: [boot loader] timeout=30 default=multi(0)disk(0)rdisk(0)partition(2)\win...

  • Page 54

    Enable 4 gb support 6-6 installing windows nt server 4.0 enterprise edition.

  • Page 55: Chapter 7

    Ncr s16 minitower server installing network operating system 7-1 chapter 7 installing netware.

  • Page 56: Overview

    Overview 7-2 installing netware overview after you have setup the system and configured it, you are ready to install the operating system. This chapter discusses installing netware on your server..

  • Page 57: Installation Overview

    Installation overview ncr s16 minitower server installing network operating system 7-3 installation overview to install netware on your server, follow these steps: • confirm cmos configuration - see chapter 2 • configure adapter settings using the adaptec bios scsiselect utility - see chapter 3 • re...

  • Page 58: Primary dos Partition

    Rebooting the server and creating a primary dos partition 7-4 installing netware rebooting the server and creating a primary dos partition to reboot the server, and create a primary dos partition, follow these steps: 1. Insert the dos boot disk into drive a. 2. Reboot the server. 3. To create a prim...

  • Page 59

    Rebooting the server and creating a primary dos partition ncr s16 minitower server installing network operating system 7-5 editing this file later requires some type of utility program, such as the dos edit program. Note: if duplexing, repeat the boot steps 3-7 for the second hard disk..

  • Page 60: Using An Adaptec Controller

    Loading the controller’s drivers 7-6 installing netware loading the controller’s drivers in netware, you must install from cd-rom. Load your controller’s cd- rom drivers into a config.Sys file according to the controller’s instructions. You must also copy your dos version’s mscdex.Exe into a c:\dos ...

  • Page 61

    Loading the controller’s drivers ncr s16 minitower server installing network operating system 7-7 note: you may also install netware from cd-rom by using the .Dsk drivers and mounting the cd as a netware volume. If using the cd-rom drive only to install netware, we recommend using the dos-level driv...

  • Page 62: Installing Netware

    Installing netware 7-8 installing netware installing netware during the installation processes, you are asked many hardware-specific questions. Most of these can be answered by choosing the default (highlighted) option, but in some cases specific information is required. Note: know your hardware bef...

  • Page 63: Choosing Drivers

    Installing netware ncr s16 minitower server installing network operating system 7-9 choosing drivers this process looks for scsi controller drivers to enable use of the hard disk(s) and other storage devices attached to that scsi channel. 1. When prompted to “choose the server drivers - disk driver,...

  • Page 64: Completing The Installation

    Installing netware 7-10 installing netware 3. When prompted to “insert disk main server license,” insert your red-labeled user authorization disk into drive a, and press enter. 4. Netware attempts to mount the cd-rom as a volume. This process may take longer than the allotted 20 seconds and fail. Fo...

  • Page 65

    Installing netware ncr s16 minitower server installing network operating system 7-11 4. If your topology requires a different type or additional type support (such as ethernet_802.3, ethernet_ii or ethernet_snap, etc.), change the line which loads your smcpwr .Lan driver to read: load smcpwr slot=? ...

  • Page 66

    Installing netware 7-12 installing netware default installation, the server.Exe file is found in the c:wserver subdirectory. The installtion of netware is now complete..

  • Page 67: Chapter 8

    Ncr s16 minitower server installing network operating system 8-1 chapter 8 installing sco unix.

  • Page 68: Overview

    Overview 8-2 installing sco unix overview after you have setup the system and configured it, you are ready to install the operating system. This chapter discusses installing the following operating system software on your server: • sco unix sco open server release 5 • sco open server release 3.0

  • Page 69: Installation Overview

    Installation overview ncr s16 minitower server installing network operating system 8-3 installation overview to install sco unix on your server, follow these steps: • confirm the hardware setup • confirm cmos configuration - see chapter 2 • configure adapter settings using the adaptec bios scsiselec...

  • Page 70: Operating System

    Rebooting the server and installing the operating system 8-4 installing sco unix rebooting the server and installing the operating system to reboot the server, follow these steps: 1. Insert the n1 disk into the system, and boot the server. 2. For sco release 5, at the boot: prompt, press enter. When...

  • Page 71: Inserting The Cd-Rom

    Rebooting the server and installing the operating system ncr s16 minitower server installing network operating system 8-5 4. For sco release 3, at the hardware setup screen, the installation media is scsi cd-rom. For sco open system software release 3.0, you must have the cd-rom on host adapter 0 an...

  • Page 72: Rebooting The System

    Rebooting the server and installing the operating system 8-6 installing sco unix rebooting the system to reboot the system, follow these steps: 1. Reboot and watch for any errors. 2. Login as “root” (administrator) and test the system. 3. Press ctrl + alt + f1 for login prompt on the main console sc...

  • Page 73: Communications

    Sco release 3: installing tcp/ip communications ncr s16 minitower server installing network operating system 8-7 sco release 3: installing tcp/ip communications always defer network installation, because there may not be a driver listed within the sco unix installation for the nic configured in the ...

  • Page 74: Completing The Installation

    Sco release 3: installing tcp/ip communications 8-8 installing sco unix 6. Select your specific driver from the list and enter the corresponding number at the prompt. If your driver is not listed, you must complete the previous steps first. 7. When the “add chain sco_tcp->smpw0?” prompt displays, en...

  • Page 75: Communications

    Sco release 5: installing tcp/ip communications ncr s16 minitower server installing network operating system 8-9 sco release 5: installing tcp/ip communications to install tcp/ip, follow these steps: 1. Enter maintenance mode (press enter on boot, init 1 or shutdown -i1). 2. Type “/etc/custom” and p...

  • Page 76

    Sco release 5: installing tcp/ip communications 8-10 installing sco unix 4. Select add protocol. Observe the following: “select one networking product to be added to: smpw smc8432, 8434 and 9332 ethernet adapter, board 0 hw smpw smc 8432, 8434 and 9332 ethernet adapter, board 0 * - scotcp/ip - scoip...

  • Page 77: Chapter 9

    Ncr s16 minitower server installing network operating system 9-1 chapter 9 installing unixware.

  • Page 78: Overview

    Overview 9-2 installing unixware overview after you have setup the system and configured it, you are ready to install the operating system. This chapter discusses installing unixware on your server..

  • Page 79: Installation Overview

    Installation overview ncr s16 minitower server installing network operating system 9-3 installation overview to install unixware on your server, follow these steps: • confirm the hardware setup • confirm cmos configuration - see chapter 2 • configure adapter settings using the adaptec bios scsiselec...

  • Page 80: Operating System

    Rebooting the server and installing the operating system 9-4 installing unixware rebooting the server and installing the operating system to reboot the server, follow these steps: 1. Insert the sco unixware install disk 1 of 1 into the system, and boot the server. 2. The sco splash screen displays. ...

  • Page 81: Observing Screen Messages

    Rebooting the server and installing the operating system ncr s16 minitower server installing network operating system 9-5 selecting the installation method to select the installation method, follow these steps: 1. When prompted to select the installation method, select install from cd- rom (the defa...

  • Page 82: Rebooting The System

    Rebooting the server and installing the operating system 9-6 installing unixware reinserting the host bus adapter (hba) driver disk to reinsert the host bus adapter (hba) driver disk, follow these steps: 1. When prompted to reinsert the hba driver disk you used earlier, insert the disk and press ent...

  • Page 83

    Rebooting the server and installing the operating system ncr s16 minitower server installing network operating system 9-7 8. Press enter to start the mouse test. Follow the on-screen instructions to test. 9. When the “owner’s account” prompt displays, enter a name and login id. Select apply, and pre...

  • Page 84

    Rebooting the server and installing the operating system 9-8 installing unixware.

  • Page 85: Chapter 10

    Ncr s16 minitower server installing network operating system 10-1 chapter 10 installing os/2.

  • Page 86: Overview

    Overview 10-2 installing os/2 overview after you have setup the system and configured it, you are ready to install the operating system. This chapter discusses installing os/2 on your server..

  • Page 87: Installation Overview

    Installation overview ncr s16 minitower server installing network operating system 10-3 installation overview to install os/2 on your server, follow these steps: • confirm the hardware setup • confirm cmos configuration - see chapter 2 • configure adapter settings using the adaptec bios scsiselect u...

  • Page 88: Operating System

    Rebooting the server and installing the operating system 10-4 installing os/2 rebooting the server and installing the operating system to reboot the server, follow these steps: 1. Insert the installation disk for cd-rom and power up the system. At the welcome screen, press enter. 2. When prompted, r...

  • Page 89

    Rebooting the server and installing the operating system ncr s16 minitower server installing network operating system 10-5 8. When the advanced options screen displays, select ok. 9. When the complete screen displays, select ok. Editing config.Sys and rebooting to edit config.Sys and reboot, follow ...

  • Page 90

    Rebooting the server and installing the operating system 10-6 installing os/2.

  • Page 91: Chapter 11

    Ncr s16 minitower server installing network operating system 11-1 chapter 11 installing mp-ras.

  • Page 92: Overview

    Overview 11-2 installing mp-ras overview after you have setup the system and configured it, you are ready to install the operating system. Refer to the section, “configuration settings required for installing mp-ras,” at the end of this chapter. This chapter discusses installing ncr unix svr4 mp-ras...

  • Page 93: Installation Overview

    Installation overview ncr s16 minitower server installing network operating system 11-3 installation overview to install mp-ras 3.01.01 on your server, follow these steps: • confirm the cmos settings using bios setup - see chapter 2 • confirm the adapter settings using the adaptec bios scsiselect ut...

  • Page 94: Operating System

    Rebooting the server and installing the operating system 11-4 installing mp-ras rebooting the server and installing the operating system when installing ncr unix svr4 mp-ras 3.01.01, you may perform a default or interactive installation, using either tape or cd-rom installation media. Using cd-rom i...

  • Page 95: Restarting The Installation

    Rebooting the server and installing the operating system ncr s16 minitower server installing network operating system 11-5 may boot using the maintenance disks, mount the drive on which the installation failed, and read the log.Install file in the /var/spool/install directory. Restarting the install...

  • Page 96

    Performing a default installation 11-6 installing mp-ras performing a default installation the following sections outline the default installation procedure. Booting from the installation media to install the ncr unix svr4 mp-ras 3.01.01 operating system software, you must boot the system from boot ...

  • Page 97

    Performing a default installation ncr s16 minitower server installing network operating system 11-7 7. When you are prompted by the system, remove the boot flex #2 from the flex drive now. The following menu displays: select one of the following: 1. Perform installation 2. Perform system maintenance...

  • Page 98

    Performing a default installation 11-8 installing mp-ras entering the system name, date, and time after you select the type of installation, the following messages display: ## please enter a system name for this system. ## this will set the node name and the system name. ## this name will be used fo...

  • Page 99

    Performing a default installation ncr s16 minitower server installing network operating system 11-9 3. Insert the installation media (“core”) into the appropriate device, and press enter. If you insert the media in the wrong device, a message prompts you to insert it in the correct device. Do not re...

  • Page 100: Installing Licenses

    Performing a default installation 11-10 installing mp-ras 1: 2047 megabyte scsi disk /dev/rdsk/c100t1d0s0 2: 4095 megabyte scsi disk /dev/rdsk/c110t4d0s0 to select a secondary (non-root) disk, type the disk number and press enter. Note: the above list may vary depending on the disks installed in you...

  • Page 101

    Performing a default installation ncr s16 minitower server installing network operating system 11-11 option meaning file select this option when your licenses are contained in a readable ascii file, such as when a license file has been e-mailed to you from the ncr support organization. Manual select...

  • Page 102

    Performing a default installation 11-12 installing mp-ras 5. If you are finished selecting licenses to install, type x to exit the installing licenses screen. 6. Remove the license flex when prompted. No further user interaction is required until the “compatibility updates” media is requested. 7. Re...

  • Page 103: Turning The System Off

    Turning the system off ncr s16 minitower server installing network operating system 11-13 turning the system off never turn the system off without performing an orderly shutdown. Use the following procedure to perform an orderly shutdown: note: this procedure is not part of the installation. You are...

  • Page 104

    Performing additional administrative tasks 11-14 installing mp-ras performing additional administrative tasks after you have completed the installation, you may need to perform some or all of the following administrative tasks to make your system fully operational: • log in to the system administrat...

  • Page 105: Installing Mp-Ras

    Configuration settings required for installing mp-ras ncr s16 minitower server installing network operating system 11-15 configuration settings required for installing mp-ras the configuration settings required for mp-ras are listed in this section. Hard disk group • on-board ide hard disk controlle...

  • Page 106

    Configuration settings required for installing mp-ras 11-16 installing mp-ras embedded adaptec aic-7880 scsi controller • on board scsi aic-7880 – enabled • boot device – enabled • configure the on board scsi to irq 11 disk array adapter mylex raid controller • disable the on board scsi boot device ...

  • Page 107: Used Resources

    Configuration settings required for installing mp-ras ncr s16 minitower server installing network operating system 11-17 used resources the table below indicates irq resources. Table 11-2. Irq settings irq use 0 system resources 1 system resources 3 serial port 2 4 serial port 1 5 pci vga or etherne...

  • Page 108

    Configuration settings required for installing mp-ras 11-18 installing mp-ras.