Nebula MH-B373 User Manual - page 7
10
3.5
PT.RANGE
3.6
SPECIAL
◆【
】
Enter
to choose
without delay or
3seconds delay
◆【
】
Enter
to choose
DMX control reset or
DMX cannot
control reset
◆【Power】
◆【Color】
◆【 Fan】
hoose
DMX to control fan or
DMX cannot control fan
◆【
Dmxerror
】
hoose
Save
After loss of DMX Save,
Black
After loss of DMX black
BlackD
【BlackD】
【No】
【Yes】
Reset
【Reset】
【DMX】
【System】
Enter 【Power】 to choose the power as NORMAL or HIGH.
C
【DMX】
【System】
C
【
】
【
】
【COLOR】 is for activate/unactivate the color calibration functions.
3.7
EDIT
P/Begin
P/End
T/Begin
T/End
Use
Range
(000~255)
No
Yes
(000~255)
(000~255)
(000~255)
BlackD
Special
Reset
Power
Color
Fan
No
Yes
DMX
System
Normal
High
Uc
DMX
System
Rgbtow
Off
Edit
Step
Pan
Speed
Tilt
Red
Green
Blue
Dimmer
Zoom
(000~255)
(000~255)
(000~255)
(000~255)
(000~255)
(000~255)
(000~255)
(000~255)
(000~255)
(000~255)
(000~255)
Strobe
●【P/Begin】
【
】
●【P/End】
【
】
●【T/Begin】
【
】
●【T/End】
【
】
●【 Use】
【 Use】
【Yes】
Set pan start value
000~255
Set pan finish value
000~255
Set Tilt start value
000~255
Set Tilt finish value
000~255
Enter
and select
to open the operation of X/Y angle
Dmxerror
Save
Black
Time
(000~255)
Use
11
3.8 EXTRA
◆ When the user enter 【 password】and input the correct password, the
hidden menu 【Cablid】,【default】 will appear on display panel, and
the user is able to reset the 【DEFAULT】values of all functions.
The default access code is UP + DOWN + UP + DOWN..
3.9 CALIB
Time
Use
(000~255)
No
Yes
0000
Extra
Password
4200K
RED
GREEN
BLUE
(000~255)
(000~255)
(000~255)
4900K
RED
GREEN
BLUE
(000~255)
(000~255)
(000~255)
Calib
3400K
3200K
RED
GREEN
BLUE
(000~255)
(000~255)
(000~255)
RED
GREEN
BLUE
(000~255)
(000~255)
(000~255)
5600K
RED
GREEN
BLUE
(000~255)
(000~255)
(000~255)
Edit
● Enter the【 Edit 】mode to edit the custom programs by adjusting the
value of【Step】,【Pan】,【Tilt】,【Speed】,【Blue】,【Zoom】,
【Green】,【Red】,【Dimmer】,【Strobe】,【 Time】
●
【 Use】
【Yes】
‘
【 ime】
【 ime】
【 Use】
【 ime】
【 Use】
【 ime】
【 Use】
【
】
Enter
and select
to run the steps user need.
Note: if user want to circulate the created steps, please set the last step
s
T
as 0
For example, there are 3 steps, the setting should be like belowed:
Step 1
T
= 4
= Yes
Step 2
T
= 5
= Yes
Step 3
T
= 0
= Yes