Summary of EasyNote A7
Page 1
Versa s940 disassembly manual.
Page 2
Nec versa s940/pb easynote a7 disassembly manual page 2 table of contents overview.................................................................................................................................................................3 technician notes..........................................
Page 3
Nec versa s940/pb easynote a7 disassembly manual page 3 overview this document contains step-by-steps disassembly instructions for the versa s940/easynote a7 chassis. The instructions are illustrated where necessary with images of the part that is being removed or disassembled. Furthermore, the scre...
Page 4
Nec versa s940/pb easynote a7 disassembly manual page 4 hazardous voltage there is hazardous voltage present inside the computer when it is connect to an ac supply, even when the computer’s power switch is off. Exposure to hazardous voltage could cause personal injury. To avoid risk of injury, conta...
Page 5
Nec versa s940/pb easynote a7 disassembly manual page 5 removing the battery perform the following steps to remove the battery: 1. Make sure to power off the versa s940/easynote a7. 2. Turn the unit upside down. 3. Unlock the battery and slide it out of its place as the arrow shows in fig. 1 fig. 1 ...
Page 6
Nec versa s940/pb easynote a7 disassembly manual page 6 removing the memory module to remove the memory module, first remove the battery (see removing the battery ), then perform the following steps: 1. Release the three screws retaining the memory module cover. Fig. 2 removing the screws retaining ...
Page 7
Nec versa s940/pb easynote a7 disassembly manual page 7 removing the wlan card module to remove the wlan card module, first remove the memory module cover (see removing memory module ) then perform the following steps: 1. Disconnect the wireless antenna connector and release the wlan card module as ...
Page 8
Nec versa s940/pb easynote a7 disassembly manual page 8 removing the hard disk drive to remove the hard disk drive, first remove the battery (see removing the battery ), then perform the following steps: 1. Remove the screws as shown in fig. 5 fig. 5 removing the hard disk drive cover 2. Carefully p...
Page 9
Nec versa s940/pb easynote a7 disassembly manual page 9 3. Remove four screws that around hdd module. Fig. 7 hdd module note: when installing hdd, make sure the hdd module strap properly insert into base unit as shown in below picture. M4x3 silver.
Page 10
Nec versa s940/pb easynote a7 disassembly manual page 10 removing the optical disk drive to remove the odd, first remove the battery (see removing the battery ) and memory module cover (see removing memory module ) then perform the following steps: 1. Use pin to eject the optical drive via emergency...
Page 11
Nec versa s940/pb easynote a7 disassembly manual page 11 removing the cpu to remove the cpu first remove the battery (see removing the battery ) then perform the following steps: 1. Losses four screws that retaining the cpu cover as shown in fig. 10 fig. 10 removing the screws retaining cpu cover 2....
Page 12
Nec versa s940/pb easynote a7 disassembly manual page 12 3. Unlock the cpu from the cpu socket and lift up the cpu carefully. Fig. 12 unlocking the cpu.
Page 13
Nec versa s940/pb easynote a7 disassembly manual page 13 removing the keyboard to remove the keyboard, first remove the battery (see removing the battery ), then perform the following steps: 1. Release two screws on keyboard cover as shown in fig. 13 fig. 13 releasing the keyboard cover 2. Lift up t...
Page 14
Nec versa s940/pb easynote a7 disassembly manual page 14 3. Unscrew two screws at the bottom as shown in fig. 15 fig. 15 unscrewing keyboard screws caution: if using wrong screws during keyboard assemble might result damage to keyboard. Thus please mark those screws carefully during dissemble. 4. Fl...
Page 15
Nec versa s940/pb easynote a7 disassembly manual page 15 5. Lift up the keyboard and disconnect it from the system as shown in fig. 17 fig. 17 disconnecting the keyboard flat cable removing the lcd module to remove the lcd module first remove the battery (see removing the battery ), remove wlan card...
Page 16
Nec versa s940/pb easynote a7 disassembly manual page 16 2. Disconnect lcd cable connection and remove four screws retaining the heat plate as shown in fig. 19 fig. 19 removing the screws retaining the lcd module 3. Carefully lift up the lcd module. M2.5x6 silver.
Page 17
Nec versa s940/pb easynote a7 disassembly manual page 17 removing the lcd panel to remove the lcd panel, first remove the lcd module (see removing the lcd module ), then perform the following steps: 1. Use a pin to remove the rubber cover on the lcd module as shown in fig. 20 2. Remove all screws as...
Page 18
Nec versa s940/pb easynote a7 disassembly manual page 18 4. Release four screws at the both side of lcd hinge as shown in fig. 22 fig. 22 unscrew lcd penal 5. Disconnect all connectors on inverter board as shown in fig. 23 fig. 23 removing the inverter board 6. Carefully lift up the lcd panel. 7. Re...
Page 19
Nec versa s940/pb easynote a7 disassembly manual page 19 removing the top cover to remove the top cover , first remove the battery (see removing the battery ), remove the hdd (see removing the hard disk drive ), remove the optical disk drive (see removing the optical disk drive ), remove the cpu (se...
Page 20
Nec versa s940/pb easynote a7 disassembly manual page 20 3. Disconnect the touch pad connector and remove all screws as shown in fig. 27 fig. 27 top cover 4. Carefully lift up the top cover. A = m2.5x4 silver b = m2.5x5 silver.
Page 21
Nec versa s940/pb easynote a7 disassembly manual page 21 removing the main board to remove the main board, first remove the top cover (see removing top cover ) then perform the following steps: 1. Remove all connection and screws on main board as shown in fig. 28 fig. 28 main board 2. Carefully lift...
Page 22
Nec versa s940/pb easynote a7 disassembly manual page 22 3. Disconnect audio board from main board as shown in fig. 30 fig. 30 vga board 4. This step only applicable to easynote a7. Flip over the main board and release two screws on s-video board as shown in fig. 31 fig. 31 s-video board on main boa...
Page 23
Nec versa s940/pb easynote a7 disassembly manual page 23 removing the speaker assembly to remove the speaker assembly, first remove the main board (see removing the main board ) then perform the following steps: 1. Remove the screws holding speaker assembly as shown in fig. 32 fig. 32 speaker assemb...
Page 24
Nec versa s940/pb easynote a7 disassembly manual page 24 dip switch settings no dip switch available on ed1 platform. Screws m2.5x2.5 silver m2.5x4 silver m2.5x8 copper m2.5x5 black m2.5x5 silver m2.5x6 silver m2.5x6 copper m2x7 silver m2x3 silver m2x4 silver m2.5x4 copper m2.5x3 silver m2x4.5 black...
Page 25
Nec versa s940/pb easynote a7 disassembly manual page 25 notice the information in this guide is subject to change without notice. This guide contains information protected by copyright. No part of this guide may be photocopied or reproduced in any form or by any means without prior written consent ...