1. DL manuals
  2. NEC
  3. Monitor
  4. LCD1990SX-BK - 1500:1 LCD With DVI
  5. User Manual

NEC LCD1990SX-BK - 1500:1 LCD With DVI User Manual

Other manuals for LCD1990SX-BK - 1500:1 LCD With DVI: Specifications
Manual is about: 19" Professional Desktop Monitor

Summary of LCD1990SX-BK - 1500:1 LCD With DVI

  • Page 1

    Multisync lcd1990sx user’s manual.

  • Page 2: Index

    Index warning, caution ........................................................................................................................ English-1 declaration .................................................................................................................................. Eng...

  • Page 3: Declaration

    English english-1 warning caution caution: to reduce the risk of electric shock, make sure power cord is unplugged from wall socket. To fully disengage the power to the unit, please disconnect the power cord from the ac outlet.Do not remove cover (or back). No user serviceable parts inside. Refer se...

  • Page 4: Statement

    English-2 canadian department of communications compliance statement doc: this class b digital apparatus meets all requirements of the canadian interference-causing equipment regulations. C-ul: bears the c-ul mark and is in compliance with canadian safety regulations according to can/csa c22.2 no. 6...

  • Page 5: Contents

    English english-3 contents your new nec monitor box* should contain the following: • multisync lcd1990sx monitor with tilt/swivel/pivot/height adjust stand • power cord • video signal cable (15-pin mini d-sub male to dvi-a) • video signal cable (dvi-d to dvi-d cable) • user’s manual • cd-rom • cable...

  • Page 6: Quick Start

    English-4 figure c.1 figure c.2 highest stand position quick start to attach the lcd monitor to your system, follow these instructions: 1. Turn off the power to your computer. 2. For the pc or mac with dvi digital output: connect the dvi signal cable to the connector of the display card in your syst...

  • Page 7

    English english-5 figure e.1 vacation switch power button figure c.3 figure d.1 figure d.2 figure c.4 7. Hold all cables firmly and place the cable cover onto the stand (figure d.1). To remove the cable cover, lift the cover off as shown in figure d.2. 8. Connect one end of the power cord to the ac ...

  • Page 8

    English-6 tilt grasp top and bottom sides of the monitor screen with your hands and adjust the tilt as desired (figure ts.1). Figure ts.1 swivel grasp both sides of the monitor screen with your hands and adjust the swivel as desired (figure ts.2). Note: handle with care when tilting the monitor scre...

  • Page 9

    English english-7 figure s.1 4. Place one hand around the base and one hand on the quick release lever. Move the quick release lever in the direction indicated by the arrows (figure s.2). 5. Lift up the bottom of the stand to unhook it from the monitor (figure s.3). The monitor can now be mounted us...

  • Page 10: Controls

    English-8 controls osd (on-screen display) control buttons on the front of the monitor function as follows: to access osd menu, press any of the control buttons (exit, left, right, up, down). To change signal input, press the select button. Note: osd must be closed in order to change signal input. *...

  • Page 11

    English english-9 eco mode decreases the amount of power consumed by reducing the brightness level. 1: decreases the brightness by 25%. 2: decreases the brightness by 50%. Custom: decreases the brightness level as determined by the user. Refer to the advanced osd menu for custom setting instructions...

  • Page 12

    English-10 auto fine (analog input only) this function automatically and periodically adjusts the “fine” setting for change in signal condition. This function adjusts approximately every 33 minutes. Expansion sets the zoom method. Full: the image is expanded to 1280 x 1024, regardless of the resolut...

  • Page 13

    English english-11 off timer monitor will automatically power-down when the end user has selected a pre-determined amount of time. Before powering off, a message will appear on the screen asking the user if they want to delay the turn off time by 60 minutes. Press any osd button to delay the turn of...

  • Page 14

    English-12 resolution notifier this optimal resolution is 1280 x 1024. If on is selected, a message will appear on the screen after 30 seconds, notifying you that the resolution is not at 1280 x 1024. Hot key you can adjust the brightness and contrast directly. When this function is set to on, you c...

  • Page 15: Recommended Use

    English english-13 recommended use safety precautions and maintenance for optimum performance, please note the following when setting up and using the lcd colour monitor: • do not open the monitor. There are no user serviceable parts inside and opening or removing covers may expose you to dangerous ...

  • Page 16

    English-14 correct placement and adjustment of the monitor can reduce eye, shoulder and neck fatigue. Check the following when you position the monitor: • for optimum performance, allow 20 minutes for warm-up. • adjust the monitor height so that the top of the screen is at or slightly below eye leve...

  • Page 17: Specifications

    English english-15 specifications monitor specifications multisync lcd1990sx monitor notes lcd module diagonal: 48.2 cm/19.0 inches active matrix; thin film transistor (tft) liquid viewable image size: 48.2 cm/19.0 inches crystal display (lcd); 0.294 mm dot pitch; native resolution (pixel count): 12...

  • Page 18: Features

    English-16 features triple input technology: triple input technology allowing up to 3 input sources to be connected to a single monitor. The dvi-i connector supports both analog and digital input signals. Legacy analog input is supported using a traditional 15-pin vga connector. Triple input technol...

  • Page 19: Troubleshooting

    English english-17 troubleshooting no picture • the signal cable should be completely connected to the display card/computer. • the display card should be completely seated in its slot. • check the vacation switch should be in the on position. • front power switch and computer power switch should be...

  • Page 20: Appendix

    English-18 appendix if you need detailed information about the controls, please use the advanced menu. • turn off your monitor. • turn on your monitor by pushing the “power” and “select” button at the same time for at least one second simultaneously. Then press the control buttons (exit, left, right...

  • Page 21

    English english-19 tag3 auto adjust automatically adjusts the image position and h.Size settings and fine settings. (analog input only) press “select” to activate auto adjustment. Signal adjust determines when the auto adjustment is activated automatically. (analog input only) the choices are “simpl...

  • Page 22

    English-20 h.Zoom the image is expanded from 1 to 3 times in the horizontal (h. Expansion) direction by (available in custom 0.01 increments. Expansion mode only) v.Zoom the image is expanded from 1 to 3 times in the vertical (v. Expansion) direction by (available in custom 0.01 increments. Expansio...

  • Page 23

    English english-21 video detect selects the method of video detection when more than one computer is connected. Press “left” or “right” to select. First: the video input has to be switched to “first” mode. When current video input signal is not present, then the monitor searches for a video signal f...

  • Page 24

    English-22 osd lock out this control completely locks out access to all osd control functions. When attempting to activate osd controls while in the lock out mode, a screen will appear indicating the osd controls are locked out. There are three types of osd lock out: osd lock out with brightness and...

  • Page 25

    English english-23 screen saver use the screen saver to reduce the risk of image persistence. Motion (default off): screen image moves periodically in 4 directions in order to reduce the risk of image retention. Timing for motion can be set so the screen image moves in intervals from every 10 to 900...

  • Page 26

    English-24 tagc schedule programs the monitor’s working schedule. Schedule the power on and power off with hour and a day of the week. Also sets the input port. This osd can’t remove except exit. Using the “schedule” function allows you to set up to seven different scheduled time intervals when the ...

  • Page 27

    English english-25 using the auto brightness function the brightness of the lcd screen can be set to increase or decrease depending on the amount of ambient light within the room. If the room is bright, the monitor becomes correspondingly bright. If the room is dim, then the monitor will dim accordi...

  • Page 28: Tco’03

    English-26 tco’03 congratulations! The display you have just purchased carries the tco’03 displays label. This means that your display is designed, manufactured and tested according to some of the strictest quality and environmental requirements in the world. This makes for a high performance produc...

  • Page 29

    English english-27 nec display solutions is strongly committed to environmental protection and sees recycling as one of the company’s top priorities in trying to minimize the burden placed on the environment. We are engaged in developing environmentally- friendly products, and always strive to help ...