NEC PF32W503 Instruction Manual

Manual is about: Colour Television

Summary of PF32W503

  • Page 1

    Instruction manual colour television pf32w503 1 table of contents safeguards 2 introduction features 3 installation 3 to connect the aerial 4 to prepare the remote control 4 identification of controls 5 remote control 7 turning the power on/off 8 turing the power on/off 8 auto power off 8 last mode ...

  • Page 2

    2 safeguards to operate your receiver at the peak performance, please read this instruction manual carefully and retain it for the future reference. M water and moisture : never install the set in the following places : in the bathroom, in a wet basement(dripping or splashing water). M heat : never ...

  • Page 3

    4 to connect the aerial to prepare the remote control installation optimum reception of colour requires a good signal and will generally mean that an outdoor aerial must be used. The exact type and positioning of the aerial will depend upon your particular area. Notes m when using an outdoor aerial,...

  • Page 4

    6 back a/v output terminal this always provides with tv signal output of the selected channel. Video 1 input terminals or dvd input terminals top video 2(scart jack) input/output terminal (scart does not supports s-video) a/v out of scart terminal will provide with tv signal output of the selected c...

  • Page 5

    Turning the power on/off the following describes how to turn the tv on/off using the main switch and the remote control. 1. Press the main power switch. The power indicator lit up red or amber. In displays the standby mode that the power indicator lit up red. 2. If no picture appears, press the “pow...

  • Page 6

    10 edit 1. Press the menu button to select install. 2. Press the c / b buttons and then install system. 3. Select edit with the pr y / x buttons and press the c / b buttons to start edit. 4. Delete program position data. Position the blue-line to the program to delete with the pr y / x buttons and t...

  • Page 7

    12 to select the panorama or zoom 1~zoom 4 screen 1. By pressing the wide/zoom button in remote control, the following seven modes change cyclically. 2. Or press the menu button to features. 3. And then to be displayed on the right appearance. Select the zoom with the pr y / x buttons. 4. By pressin...

  • Page 8

    14 to select the sound mode 1. Press the selectable sound ( ) button to select the desired sound quality. Normal, favourite, music, speech can be selected cyclically. 2. Or press the menu button to select the sound and then to be displayed on the right appearance. Select the preset with the pr y / x...

  • Page 9

    16 stereo programs press the stereo/bilingual select ( )button to select to nicam- stereo/mono mode. Bilingual programs 1. When a bilingual program is received dual 1, dual 2 appears. 2. Press the stereo/bilingual select button to be heard. The sound differs according to transmission system : dual 1...

  • Page 10

    18 to turn on the tv automatically(wake time) with the clock, the wake time, the wake pr. Preset, the tv will automatically turn on to a preset program number at a reset time. Set the timer on. Select the wake time with pr y / x buttons. Then, press direct key(0~9) to set the wake up time. To turn o...

  • Page 11

    20 to select the screen color when no signal is being received, the tv will automatically turn blue or red at the time screen blue or screen red on. 1. Press the menu button to select the features and then to be displayed on the right appearance. Press pr y / x buttons to select the screen. 2. Press...

  • Page 12

    22 watching picture in picture the unit is capable of displaying two picture with the small sub picture simultaneously. This is called the picture-in-picture function. A tv picture or a picture from external source equipment such as a vtr can be displayed as another picture. Pip mode sub ch down sub...

  • Page 13

    24 to switch the main and sub-picture of the pip press the swap button when a picture-in-picture is displayed. The main picture(the large picture) and sub-picture(the small picture) are switched. Press the swap button again to switch again. To freeze the sub-picture press the still button when a sub...

  • Page 14

    26 connecting video l when connecting the video to the back of the tv 1. Prepare the connective plug for picture/sound. 2. Connect the video picture output terminal with the tv picture input terminal. 3. Connect the video sound output terminal with the tv sound input terminal. 4. Press the tv/video/...

  • Page 15

    28 connecting with s picture video video audio r l s-video sound output s-picture output hi-fi stereo video l side connector m to watch tv in clear field by inputting s picture. When repeating high-quality field video, you can enjoy clear and sharp picture by connecting it with tv s-vhs terminal. 1....

  • Page 16

    30 connecting with audio set m when listening to sound in powerful audio, while watching the picture on tv. M connect external input terminal of audio to right & left sound output of tv signal. Right left m when connecting other equipment, please ensure you turn the main switch off to prevent any da...

  • Page 17

    32 to select the text mode first, turn on your tv set and choose your tv program. Then press the text( )button to switch the receiver to teletext mode. To select any other page, simply press the three of the page selector buttons or pr y / x buttons. The page number requested is displayed on the upp...

  • Page 18

    34 specification tv standard color system sound system rated voltage sound output power channel coverage tuning system program no. Indication program selection aux. Terminal power consumption pal/secam, ntsc 3.58/4.43(av) b/g, d/k, i, h 110-240v~, 50/60hz 8w x 8w hyper band catv vhf l : e2(48.25mhz)...