1. DL manuals
  2. North Star
  3. Edger
  4. M191185C.6
  5. Owner's Manual

North Star M191185C.6 Owner's Manual

Manual is about: M191185C.6

Summary of M191185C.6

  • Page 1

    M191185c.6 item number : 191185 serial number : owner’s manual trencher/edger: cuts trenches in dirt. Any questions, comments, problems or parts orders call northstar product support 1-800-270-0810

  • Page 2: Table Of Contents

    2 table of contents hazard signal word definitions………………………………......2 important safety rules ................................................………..3,4 warning label locations ........ ....................................…………5 unpacking ....................................................................

  • Page 3: Important Safety Rules

    3 important safety rules.

  • Page 4: Important Safety Rules

    4 important safety rules 3.) fire hazard. Gasoline is highly flammable and explosive. You can be burned or seriously injured when handling fuel. -stop the engine and keep heat, sparks, and flame away. -handle fuel only outdoors. Wipe up spills immediately. 4.) tripping hazard. Make sure area is clea...

  • Page 5: Warning Label Locations

    5 warning label locations any questions, comments, problems or parts orders call northstar product support 1-800-270-0810 flying objects. Rock and dirt may fly out while trenching. Serious injury can occur. -pull trencher as you dig. Do not push. -wear safety glasses. Warning warning belt pinch poin...

  • Page 6: Unpacking

    6 unpacking closely inspect all contents in the shipping carton. - if you have damaged components: contact the freight company that delivered the unit and file a claim. - if you have missing components: contact product support at 1-800-270-0810. Engine/frame assembly handle assembly front axle (4) w...

  • Page 7: Unpacking

    7 unpacking fastener identification.

  • Page 8: Assembly Instructions

    8 assembly instructions 1.) handle assembly. - use (1) 5/16” x 3/4” bolt, (1) 5/16” x 2” bolt, & (2) 5/16” nuts to fasten the handle to the frame. - make sure the tab engages the slot. - install the 3/8” x 3 1/4” bolt and 3/8” nut. - loop the zip tie around the 3/8” bolt under the handle to loosely ...

  • Page 9: Assembly Instructions

    9 assembly instructions 2.) wheel assembly - check tires for correct air pressure prior to assembly. - use a 5/32” hex wrench to attach (2) wheels to the front axle with (2) wheel retainers. Use (2) 5/16 x 3/4” bolts to fasten the front axle to the frame. - fasten the (2) wheels to the frame with (2...

  • Page 10

    10 machine component identification 1.) control lever . Used to start and stop cutting blade. 2.) turnbuckle. Adjusts belt tension. As belts wear, retensioning may be required. See “belt tension” section of this manual. 3.) engine. Air-cooled engine provides power for cutting blade. 4.) engine on/of...

  • Page 11: Operation Instructions

    11 operation instructions work site preparation the trencher/edger is operated by pulling the machine along a planned path. Mark your path before starting the trenching operation. Locate any aboveground obstacles in your path and plan a safe route to avoid them. Mark a well defined, easy to follow p...

  • Page 12: Operation Instructions

    12 operation instructions trenching danger do not push machine during operation trencher is designed as a “pull” type machine only. Pushing the machine will expose the operator to flying debris. 1.) starting engine : refer to engine owners’ manual for proper engine starting procedure. Do not run eng...

  • Page 13: Operation Instructions

    13 operation instructions changing trench depth the trencher/edger can cut a 7,6 or 5” deep trench. Simply unbolt the axle assembly and move it to the next hole pattern, or “flip” the axle assembly to achieve the desired cutting depth. Changing blades - follow lockout procedure as outlined in the ma...

  • Page 14: Maintenance And Storage

    14 maintenance and storage lockout procedure before performing maintenance, the trencher/edger must be placed in lockout mode. 1.) turn off engine. 2.) disconnect engine spark plug wire. Belt tension 1. The ideal belt tension is the lowest tension at which the belts will not slip under peak load con...

  • Page 15: Maintenance And Storage

    15 maintenance and storage sheave alignment eventually, sheave removal or replacement may become necessary. Inspect sheaves for cracks or a groove bottom that is shiny. Sheaves must be aligned to within 1/16” when reinstalled. Caution: after performing maintenance, make sure all guards, shields, and...

  • Page 16: Specifications

    16 specifications engine................................................. 6.5 hp honda trench depth (with standard blade).... 7” trench width (with standard blade).... 1 1/2” overall dimensions............................ 65 1/2” l x 26” w x 36 1/2” h dry weight.........................................

  • Page 17: Parts Explosion

    17 parts explosion – rev c.6 item part# description qty 21 37977 idler pulley 1 22 38068 belt guard 1 23 37968 control cable 1 24 37962 protective mat 1 25 37964 guard retainer 1 26 38036 warning label 1 27 38164 trench path label 1 28 38035 danger label 1 29 37952 blade guard 1 30 37974 protective ...

  • Page 18

    18 this page has intentionally been left blank..

  • Page 19: Limited Warranty

    19 limited warranty dear valued customer: the northstar product you just purchased is built with the finest material and craftsmanship. Use this product properly and enjoy the benefits from its high performance. By purchasing a northstar product, you show a desire for quality and durability. Like al...

  • Page 20

    20 manufactured by northern tool + equipment co., 2800 southcross drive west p.O. Box 1499 burnsville, mn 55337-0499.