1. DL manuals
  2. Northern Industrial Tools
  3. Saw
  4. 145765
  5. User Manual

Northern Industrial Tools 145765 User Manual

Manual is about: Automatic Metal-Cutting Band Saw

Summary of 145765

  • Page 1

    Item# 145765 automatic metal-cutting band saw user’s manual assembly and operation instructions made in china.

  • Page 2: Quick-Start Guide

    Quick-start guide attention: read and follow unpacking & assembly guide before operation. 1. Front locking bolt 5. Front wheels 2. Band saw . 6. Rear wheels 3. Locking device between saw arch and table . 7. Length-restricting device for workpiece 4. Rear locking bolt unpacking step 1. Snip the carto...

  • Page 3

    For technical questions and replacement parts, please call 1-800-556-7885. Thank you very much for choosing a northern industrial product! For future reference, please complete the owner’s record below: model: _______________ purchase date: _______________ save the receipt, warranty and these instru...

  • Page 4

    11. Always wear eye protection, refer to a.N.S.I z87.1 standard for appropriate recommendations. Also use a face or dust mask if cutting operation is dusty. 12. Always secure work with clamps or a vise. It’s safer than using your hand and frees both hands to operate tool. 13. Don’t overreach - keep ...

  • Page 5

    12. When cutting magnesium never use soluble oils or emulsions (oil-water mix) as water will greatly intensify any accidental magnesium chip fire. See your industrial coolant supplier for specific coolant recommendations when cutting magnesium. 13. To prevent corrosion of machine surface when a solu...

  • Page 6

    3. Quick-set vise clamp. X, you have to wait till the machine stops running. Then that you do not shift the speed while cutting. 500 that, to insert the location pin smoothly, move the saw blade back and forth, bringing the shifting andle to a suitable location where you can insert the location pin ...

  • Page 7

    Blade speeds when using your band saw always change the blade speed to best suit the material being cut. The material cutting chart gives sugg . Al cutting d f. Ested settings for several materials materi chart spee p.M material 60hz 50hz tools, stainless alloy steel 100 83 bearing bronze medium or ...

  • Page 8

    1. Bi-metal band saw blade is suitable for metal workpiece such as carbon steel, alloy steel, and stainless steel. Ces and hard 3. N band saw blades are suitable for wood, fiber glass and plastic. 4. Carbide grit edge band saw blades are suit ago, carbon product and alveolate material, etc. Vertical...

  • Page 9

    Quick vise adjustment for angle cut ust rear vise to the threaded hole position. E rear vise . Tighten the a, b, c and d screws. Will not cut straight, and if the situation is not corrected if a new blade does not correct the problem, check ance between the blade and guide nd can be adjusted. Tric b...

  • Page 10

    B. Turn the hex head screw clockwise until it stops (do not tighten). C. Turn the set screw clockwise until it bottoms, then continue for half a turn and check the tra , go back to step 4. Blade guide bearing assemblies so that the backside of the blade ing. If necessary to adjust, go back to step 4...

  • Page 11

    Symptom cause (s) possible corrective action 1. Incorrect blade tension ust does not slip on wheel 1. Adjust to where blade j 2. Incorrect speed or feed 2. Check machinist handbook 3. Material loose in vise 3. Clamp work securely excessive blade 4. Blade rubs on wheel flange 4. Adjust wheel alignmen...

  • Page 12

    Assembly drawing page 11 of 15 page 11 of 15.

  • Page 13

    Parts list ref # description ref # description 1 valve cock support 10 c-ring s8 2 s. Washer m8 11 bolt m5x8 3 set screw soc. Hd. M8x30mrn 12 b lade cover (front) 4 nut 3/8nf 13 water nozzle 5 s.Washer 3/8"x2.2mm 14 valve 1/4" 6 blade ak justable (front) 15 bolt 3/16"x1/4" 7 pin 16 hose button 8 ecc...

  • Page 14

    Ref # description ref # description 19 adjusting knob 3/8" 58 brush holder 20 plate washer 3/8"x2x23 59 bolt screw 3/16”x1/2” 21 adjustable bracket (front) 60 brush 22 bow-saw 61 bolt 1/4"x1/2" 23 set screw soc. Hd. M8x16mm 62 blade 24 bolt m8x40mm 63 gear box & motor 25 s. Washer 8.3x2 64 piver bra...

  • Page 15

    Ref # description ref # description 100 bolt m10x40mm 140 bolt 1/2"x2-1/2" 101 fixed bolt 141 wheel shaft 102 stock stop rod 142 wheel 103 bolt 3/16"x1/4" 143 wheel button 104 filter net plate 144 coolant tank 105 filter net 145 drain plug 106 switch cover 146 bolt 3/16"x3/8" 107 toggle switch 147 p...

  • Page 16: Warning!

    Warning! Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the state of california to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: ● lead from lead-based paints. ● crystalline...