1. DL manuals
  2. Northwestern Bell
  3. Telephone
  4. Excursion 36000
  5. Instructions Manual

Northwestern Bell Excursion 36000 Instructions Manual

Summary of Excursion 36000

  • Page 1

    Excursion 36000 congratulations on your selection of the excursion® 36000 from northwestern bell phones. This quality 2.4ghz cordless telephone, like all genuine bell® products, has been designed to give you many years of continuous service and represents the best value for your money. It requires l...

  • Page 2

    Important service information read this manual before attempting to setup or use this instrument. It contains important information regarding sale installation and use. Keep this manual for future reference. Also save the carton, packing and proof of purchase to simplify and accelerate any needed ac...

  • Page 3

    Save these instructions important safety instructions when using your telephone equipment, basie safety precautions should always be followed to reduce the risk of fire, electric shock, and injury topersons, including the following: 1. Read and understand all instructions. 2. Follow all warnings and...

  • Page 4

    Installation precautions 1. Never install telephone wiring during a lightning storm. 2. Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations. 3. Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected a...

  • Page 5

    3. The ren is useful to determine the quantity of devices you may connect to your telephone line and still have all of those devices ring when your number is called. In most, but not all areas, the sum of the rens of all devices should not exceed five (5.0). To be certain of the number of devices yo...

  • Page 6

    Excursion® 36000 controls diagram talk button \ vol(-) button! Spk o n ^ f f button flash button headset jack * button memo button chn button visual ringer led indicator /in use led indicator /battery low led indicator vol(+) button re/pa button in use/charge led indicator/ visual ringer led indicat...

  • Page 7

    Descriptions handset controls: visual ringer led indicator/in use led indicator /battery low led indicator - (visual ringer led indicator) flashes to indicate the phone is ringing, as a signal to the user, when the ringer is switched off. (in use led indicator) flashes rapidly while auto-scanning. L...

  • Page 8

    Base umt controls: base unit charge terminals - used for charging handset batteries. We recommend that you clean these contacts periodically with an alcohol-moistened cloth or cotton swab. In use led indicator/ charge led indicator /visual ringer led indicator - (in use led indicatorjlights up stead...

  • Page 9

    Belt clip installation with the back of handset facing up, insert one side of the belt clip hook into the matching slots at the top side of handset as shown in figure2. Slide the other hook until it locks into place from the opposite side of the handset. (figure 2) wall use: . Wall mounting (standar...

  • Page 10

    Uninstalling the wall mount bracket to remove the wall mount bracket from the base unit, pull it front as shown in figure 5. (figure 5) power connection caution: you must use a class ii, 120 volt ac/6 volt dc adaptor that delivers at least 250ma. The center tip must be positive and the plug must cor...

  • Page 11

    Initial setup please follow these steps before using the cordless telephone for the first time. 1. Ensure that the handset battery pack is installed and charged fully for at least 14 hours. 2. Ensure that all connectionsoinc cord and adaptor cord) are properly inserted into rear of the base unit. Se...

  • Page 12

    Led indicator and handset in use led indicator will light up. 2. Start your conversation. 3. To end your conversation, press the talk button, the base in use/charge led indicator and handset in use led indicator will turn off. Or place the handset on the base unit, the base in use/charge led indicat...

  • Page 13

    Memory dialing you can store and recall up to 10 frequently called telephone numbers (up to 16 digits each) from the handset. Storing telephone numbers into memory: 1. Finsure that the base unit in use/charge led indicator is off and the handset is in standby mode(on-hook). 2. Press the memo button ...

  • Page 14

    To reset, place the handset on the cradle of the base unit tor five seconds. Note: to better protect the privacy and security of the user, the handset included was factory-preset to work only with the base that comes with it. This is to prevent others from using the same model units to eavesdropping...

  • Page 15

    Motors, and fans also generate noise pulses. Because radio frequencies are susceptible to these noise pulses, you may occasionally hear them in your handsel. Generally, they are minor annoyances and should not be interpreted as defects in your system. Range: because radio frequencies are used, locat...

  • Page 16: Solution

    Troubleshooting symptom no dial tone will not ring can not dial out memory feature does not work solution • check to see if the handset battery pack is connected inside the handset battery compartment. • make sure that the adaptor plug is connected to the base unit. • check for the telephone line co...

  • Page 17

    No link between the base and handset the unit locks up and becomes inoperable • the maximum number of digits that you can store for each memory location is 16 digits. See the "memory dialing"' section for more details. • you may have taken the handset at a distance away from the base that is beyond ...