1. DL manuals
  2. Norton
  3. Saw
  4. C1320P
  5. Owner's Manual

Norton C1320P Owner's Manual

Manual is about: MEDIUM CONCRETE SAWS

Summary of C1320P

  • Page 1

    Owners manual medium concrete saws model: c1320p form c1320p rev 9-2010

  • Page 2: Warranty

    2 warranty norton warrants all products manufactured by it against defects in workmanship or materials for a period of one (1) year from the date of shipment to the customer. The responsibility of norton under this warranty is limited to replacement or repair of defective parts at norton's gainesvil...

  • Page 3: Table of Contents

    3 table of contents contents page warranty information 2 i. Preparation a. Safety precautions 4-6 b. Assembly 7 c. Concrete saw specifications 8 ii. Operation a. Blade installation 9-11 b. Changing the blade side 12-14- c. Engine operation 12-14 d. Starting the engine 14-16 e. Water supply 16 f. Con...

  • Page 4: I.  Preparation

    4 i. Preparation a. Safety precautions important! The following safety precautions must always be observed. Hazard symbols fuel (gasoline) is extremely flammable and its vapors can explode if ignited. Store gasoline only in approved containers, in well-ventilated, unoccupied approved areas, and away...

  • Page 5: Dust and Silica Warning

    5 dust and silica warning grinding/cutting/drilling of masonry, concrete, metal and other materials can generate dust, mists and fumes containing chemicals known to cause serious or fatal injury or illness, such as respiratory disease, cancer, birth defects or other reproductive harm. If you are unf...

  • Page 6

    6 1. Before mounting any blade on the saw, the blade should be inspected for any damage which might have occurred during shipment, handling or previous use. 2. The blade collars and arbors should be cleaned and examined for damage before mounting the blade. 3. The blade must be properly fitted over ...

  • Page 7: I.  Preparation

    7 i. Preparation b. Assembly the c1320p push concrete saws are shipped completely assembled and ready for use except for diamond blade, gasoline, oil, and handle bar. Inspect the saw for shipping damage. If any damage is found, contact the shipper immediately and file a freight claim. Norton clipper...

  • Page 8

    8 c. C1320p concrete saw specifications dimensions/weight c1320p length (transport) 56 inch (1142 mm) width 26 inch (660 mm) height 40 inch (1016 mm) weights 310 (141kg) engine engine mfg. Honda model gx390 spec no. Gx390k1qxc9 engine type single cylinder 4 cycle horse power* 13 hp (9.5kw) @ 3,600 r...

  • Page 9: II. Operation

    9 ii. Operation read and understand this manual before running or using the machine! A. Installing the blade 1. Insure that the ignition power key switch is in the off position and then disconnect the spark plug. 2. Remove the blade shaft nut, (note: operator’s right side is a left hand thread and t...

  • Page 10

    10 4. Inspect the blade for any damage, cracks, burnt or blue areas, missing segments, and roundness of blade. Also inspect the arbor hole and drive pin hole to insure both are round. If any problems are found do not use the blade. In addition check that the blade is the correct specification for th...

  • Page 11

    11 7. Tighten the blade shaft nut (counter-clockwise for the operator’s right hand side and clockwise for the operator’s left hand side). 8. Insure that the blade guard is lowered and the blade guard locking pin is secure. Close blade guard nose. See blade installed diagram below. Blade installed 9....

  • Page 12

    12 b. Changing the blade side: 1. Insure that the ignition power key switch is in the off position and then disconnect the spark plug. 2. Remove the blade shaft nut, (note: operator’s right side is a left hand thread and the operator’s left side is right hand thread), and remove the outside collar. ...

  • Page 13

    13 6. Remove the blade shaft guard by removing the blade shaft guard retaining bolts. See blade shaft guard removal diagram below. Blade shaft guard removal 7. Place the blade on the blade shaft, lining up the drive pin hole in the blade with the drive pinhole in the inside collar. Note: diamond bla...

  • Page 14

    14 12. Remove the pointer and reattach it to the operators left hand side of the machine. Note: reverse the orientation of the pointer 13. Reconnect the spark plug. C. Engine operation prior to attempting to operate the engine, read the information contained in the engine owner's manual. An engine o...

  • Page 15

    15 before starting, insure that the blade is properly installed, all guards are in place and in safe operating condition, and that the blade is not in contact with any surface or object. Also verify that the area where the work is to be preformed is clean, safe, and has proper ventilation and lighti...

  • Page 16

    16 pull the starter grip lightly until you feel resistance, then pull briskly. Caution: do not allow the starter grip to snap back against the engine. Return it gently to prevent damage to the starter. As the engine warms up, gradually move the choke lever to the open position. Position the throttle...

  • Page 17

    17 f. Controls raise levantar rpm/hours (rpm/horas) lower bajar 3600 rpm ignition ignicion emergency stop paro de emergencia blade dia eng rpm eng pulley diameter blade shaft rpm blade shaft pulley dia diametro de disco motor rpm diámetro en polea motor flecha disco rpm diámetro en polea de flecha d...

  • Page 18

    18 tachometer/hour meter: the tachometer/hour meter shows the engine rpm only when the engine is running. The total engine operating hours (run time) are shown when the engine is turned off. Emergency kill switch: the emergency kill switch will stop the engine when depressed. The engine will not res...

  • Page 19

    19 11. Slowly lower the blade by rotating the hand wheel clockwise until the desired depth of cut is reached. Use a reasonable rate of feed. A reasonable rate of feed will depend on depth of cut, material, and blade. Normal cutting speeds should be between 2 ft/min in very hard material and up to 10...

  • Page 20

    20 additional guide lines for sawing:  understand and follow all of the instructions in this owner’s manual.  if wet cutting, turn on the water supply so that there is a minimum of 4-6 gallons per minute of water flow!!  in critically hard aggregate, more than a single pass may be needed to cut t...

  • Page 21: III. Maintenance

    21 iii. Maintenance a. Engine maintenance follow the below schedule for engine maintenance. Note: check the honda engine manual that came with the engine for any changes to the maintenance schedule. If the charts have any differences, follow the chart in the honda engine manual. Norton does not warr...

  • Page 22

    22 always refer to the engine manual for more detailed information on checking the oil, changing oil, and oil capacity, air filter changes, and fuel type to use. Use only honda air filters. Do not clean the air filter with gasoline or other flammable solvents. A fire or explosion could result. To cl...

  • Page 23

    23 honda technical & consumer information warranty service information servicing dealership personal are trained professionals. They should be able to answer any questions you may have. If you encounter a problem that your dealer does not solve to your satisfaction, please discuss it with the dealer...

  • Page 24

    24 b. Bearings re lubrication type bearings must be relubricated daily to assure long life. The grease used should conform to the nlgi grade two consistencies and be free of any chemical impurities such as free acid or free alkali, dust rust, metal particles or abrasives. For best results, bearings ...

  • Page 25

    25 c. V-belts warning: never make adjustments to belts or pulleys while engine is running! 1. The best tension for a belt drive is the lowest tension at which the belts will not slip under full load. 2. Simply take up the drive until the belts are snug in the grooves. Run the drive for about 15 minu...

  • Page 26

    26 main causes of belt failures: premature belt failure can be attributed to the following issues: tension (too much or too little), pulley misalignment, damaged pulleys, improper handling or storage, incorrect blade specification for material being cut, and cutting too deep. Symptom possible cause ...

  • Page 27: →

    27 the bearing used to support the raising screw should be checked after each use to make sure it is turning freely and lubricated. If the bearing requires re lubrication lithium base grease is recommended. Over tightening the hand wheel during the raising or lowering the saw will damage the raise s...

  • Page 28

    28 e. Electrical diagram c1320p: 13hp manual start models only oil alert unit (bl) transistorized ignition unit (bl) oil level switch (y) (g) spark plug kill switch honda engine honda part# 36100-ze1-015 sga# 227115 bl (238038) bl (238039) (y) (bl).

  • Page 29: IV. Parts List Section

    29 iv. Parts list section a. Ordering information 1. List model number and serial number of machine. 2. List part number and serial number of part not the item number. 3. Wherever alternate parts are shown due to product improvement, inspect the part you have and provide additional description as ne...

  • Page 30

    30 3 4 5 5 4 29 5 4 3 29 4 5 5 11 30 5 4 3 5 11 30 5 4 3 5 4 3 3 4 5 3 5 8 9 7 8 13 11 12 6 26 25 3 5 5 4 3 3 4 5 2 27 1 15 14 10 17 c1320p frame group.

  • Page 31

    31 c1320p frame group item part no upc no description qty type notes 1 238171 70184628065 lift frame 1 s 2 238175 70184628066 lift frame hook 1 s 3 8041051 70184649901 scr 3/8-16 x 1 1/4 hex hd cap 23 s 4 8177012 70184650149 washer 3/8 spring lock 23 s 5 8172009 70184650123 washer 3/8 sae 23 s 6 238...

  • Page 32

    32 8 2 4 7 4 4 4 10 9 11 12 13 2 1 5 12 4 4 4 1 13 5 3 6 6 14 14 c1320p raise axle group.

  • Page 33

    33 c1320p raise axle group item part no upc no description qty type notes 1 238134 70184628082 raise axle mount 1 s sold as each. 2 238129 70184628085 rear axle bushing 1 w 3 238124 70184628272 rear wheel spacer 2 s 4 8172015 70184650129 washer 3/4 sae 8 s 5 238005 70184626921 wheel 6 x 2 x 3/4 w/ro...

  • Page 34

    34 1 2 3 4 4 5 6 7 8 9 10 8 9 10 11 12 13 14 15 17 21 12 18 19 18 19 19 20 23 c1320p blade shaft & engine group.

  • Page 35

    35 c1320p blade shaft & engine group item part no upc no description qty type notes 1 238179 70184628084 blade shaft 1 s 2 227159 70184673904 tight collar right side 1 s left hand thread 3 227190 70184674352 tight collar left side 1 s right hand thread 4 227247 70184674082 loose collar outer flange ...

  • Page 36

    36 1 10 5 14 13 16 15 14 13 7 16 15 19 c1320p blade guard and water system group.

  • Page 37

    37 c1320p blade guard and water system group item part no upc no description qty type notes 1 n1d0082 70184659115 hose swivel 1 s 2 n1c0021 70184659097 water valve 1/2" 1 s 3 9602012 70184626501 hose barb 1/2" x ½”mpt 1 s 4 n1c0113 70184659232 hose clamp 2 s 5 8041006 70184649879 scr 1/4-20 x 1 hex ...

  • Page 38

    38 1 2 6 7 9 10 11 5 4 3 8 12 8 c1320p controls and console group.

  • Page 39

    39 c1320p controls and console group item part no upc no description qty type notes 1 238120 70184627887 handle bar 1 s 2 n1c0004 70184659110 handle bar grip 2 w 3 8041006 70184649879 scr 1/4-20 x 1 hex hd cap 2 s 4 8177010 70184650144 washer 1/4 spring lock 2 s 5 8172007 70184650120 washer 1/4 sae ...

  • Page 40

    40 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 19 21 19 22 c1320p depth adjustment group.

  • Page 41

    41 c1320p depth adjustment group item part no upc no description qty type notes 1 238164 70184628181 depth screw tube 1 s 2 238234 70184628182 grease zerk 1/8 1 s 3 407035 70184682129 scr 1/4-20 x 1/4 set cup 1 s 4 238163 70184628265 nut 3/4-10 hex head 1 s 5 238165 70184628183 raise screw 1 s 6 238...

  • Page 42

    42 1 2 4 3 4 9 5 10 8 to blade guard 7 c1320p optional water tank group.

  • Page 43

    43 c1320p optional water tank group item part no upc no description qty type notes -na- 238001 70184628014 water tank kit 1 s includes: items 1, and 3 to 10 1 83357 00310007011 water tank w/cap 1 w 2 82794 00310006560 cap for water tank 1 s 3 238174 70184628015 bracket for water tank 1 s 4 8041051 7...

  • Page 44: Saint-Gobain Abrasives

    44 saint-gobain abrasives 2770 west washington stephenville, tx 76401 phone: 254-918-2310 fax: 254-918-2312.