Summary of Clipper CS1 P13
Page 1
Cs1 p13 operating instructions.
Page 2
2.
Page 3: Declaration Of Conformity
3 the undersigned manufacturer: saint - gobain abrasives s.A. 190, bd j.F. Kennedy l- 4930 bascharage declares that this product: floor saw (code): cs1 p13 honda cyclonic (70184624214) cs1 p13 honda cyclonic Ø500 (70184629389) is in conformity with the following directives: • european machinery dire...
Page 4
4.
Page 5: Cs1 P13
5 cs1 p13 operating instructions 1 basic safety instructions 6 1.1 symbols 6 1.2 machine plate 7 1.3 safety instructions for particular operating phases 7 2 general description of the cs1 8 2.1 short description 8 2.2 layout 8 2.3 technical data 9 3 assembly and commissioning 10 3.1 tool assembly 10...
Page 6
6 1 basic safety instructions the cs1 is exclusively designed for the cutting of floors made of asphalt, green and cured concrete (reinforced or not) as well as of industrial cement. Uses other than the manufacturer's instructions shall be considered as contravening the regulations. The manufacturer...
Page 7
7 1.2 machine plate important data can be found on the following plate located on the machine: 1.3 safety instructions for particular operating phases before commencing work • before commencing work, make yourself familiar with the working environment at the place of use. The working environment inc...
Page 8
8 2 general description of the cs1 any modification, which could lead to a change in the original characteristics of the machine, may be done only by saint-gobain abrasives s.A. Who shall confirm that the machine is still in conformity with the safety regulations. Saint-gobain abrasives s.A. Keeps t...
Page 9
9 the pivoting frame (3), hinged on the rear axle, is supporting the engine, the blade shaft assembly, and the protecting guards. Four heavy-duty belts drive the blade. The precisely manufactured blade shaft is fitted into two heavy-duty self-aligning pillow block bearings, including grease nipples....
Page 10
10 3 assembly and commissioning before beginning the work with the cs1, you have to assemble some parts. 3.1 tool assembly only use norton blades with the cs1. A blade with a maximum diameter of 500 mm can be fitted. All tools used must be selected with regard to their maximum permitted cutting spee...
Page 11
11 3.3 starting the machine make sure the blade is raised clear up the ground before starting the machine. Turn the fuel valve to the on position. Move the choke lever to the closed position. Note: do not use the choke if the engine is warm or the air temperature is high. Move the throttle control l...
Page 12
12 4 transport and storing take the following measures in order to transport and store the cs1 securely. 4.1 securing for transport before transporting the machine: • remove the blade. • empty the water tank. • raise the guide-a-cut in its upright position. • raise the cutting frame to its highest p...
Page 13
13 5 operating the cs1 5.1 site of work before you start working, please check the following points: • remove from the site anything, which might hinder the working procedure. • make sure the site is sufficiently well lit. • make sure you have a continual adequate view of the working area so you can...
Page 14
14 6 maintenance and service attention : to perform maintenance on the machine, always switch it off. Always wear a face mask and safety goggles while performing the maintenance of machine. 6.1 maintenance of the machine to ensure a long-term quality from the cutting with the cs1, please follow the ...
Page 15
15 6.2 maintenance of the engine regular service period perform at every indicated month or operating hour interval, whichever comes first e a c h u s e f ir s t m o n th o r 2 0 h o u rs e v e ry 3 m o n th s o r 5 0 h o u rs e v e ry 6 m o n th s o r 1 0 0 h o u rs check level engine oil change ch...
Page 16
16 air cleaner the cs1 has a dual type filter. To service the air cleaner filter, follow these instructions: • remove the nut, air cleaner cover and wing nut. • remove the pre air cleaner elements and separate them. • carefully check both elements for holes or tears and replace if damaged. • paper e...
Page 17
17 spark plug to service the spark plug, follow these instructions: • visually inspect the spark plug. Discard the plug if the insulator is cracked or chipped. • remove carbon or other deposits with a stiff wire brush. • measure the plug gap with a wire-type feeler gauge. If necessary, adjust the ga...
Page 18
18 7 faults: causes and cures 7.1 fault-finding procedures should any fault occur during the use of the machine, turn it off. Let only qualified staff make any intervention other than the one described in the previous section. 7.2 trouble-shooting guide trouble possible source resolution not enough ...
Page 19
19 guarantee can be claimed and technical support obtained from your local distributor where machines, spare parts and consumables can be ordered as well: benelux and france: from saint-gobain abrasives in the grand-duché de luxembourg free telephone numbers: belgium : 0 800 18951 france: 0 800 90 6...
Page 20
20 saint-gobain abrasives 190, bd. J. F. Kennedy l-4930 bascharage luxembourg tel.: ++352 50401-1 fax: ++352 501633 e-mail: sales.Nlx@saint-gobain.Com www.Construction.Norton.Eu 10.12.2008.