1. DL manuals
  2. Norton
  3. Power Tool
  4. CS 451 P13
  5. Operating Instructions And Spare Parts List

Norton CS 451 P13 Operating Instructions And Spare Parts List

Manual is about: Clipper

Summary of CS 451 P13

  • Page 1

    Cs 451 p13 operating instructions.

  • Page 2

    2.

  • Page 3: Declaration Of Conformity

    3 the undersigned manufacturer: saint-gobain abrasives s.A. 190, bd j.F. Kennedy l- 4930 bascharage declares that this product: floor saw: cs 451 p13 code: 70184628433 is in conformity with the following directives: • european machinery directive 2006/42/ec • electromagnetic compatibility directive ...

  • Page 4

    4.

  • Page 5: Cs 451 P13

    5 cs 451 p13 operating instructions and spare parts list 1 basic safety instructions 6 1.1 symbols 6 1.2 machine plate 7 1.3 safety instructions for particular operating phases 7 2 general description of the cs 451 9 2.1 short description 9 2.2 layout 10 2.3 technical data 12 2.4 vibration emission ...

  • Page 6

    6 1 basic safety instructions the cs 451 is exclusively designed for the cutting of floors made of asphalt, green and cured concrete (reinforced or not) as well as of industrial cement. Uses other than the manufacturer's instructions shall be considered as contravening the regulations. The manufactu...

  • Page 7

    7 danger: risk of cut 1.2 machine plate important data can be found on the following plate located on the machine: 1.3 safety instructions for particular operating phases before commencing work • before commencing work, make yourself familiar with the working environment at the place of use. The wor...

  • Page 8

    8 while the engine is running • do not move the machine whilst the blade is running idle. • do not run the machine without the security guards in place. • apply cooling water continuously whilst cutting and in good time (even when dry cutting to avoid dust)! Petrol powered machines: • always use the...

  • Page 9

    9 2 general description of the cs 451 any modification, which could lead to a change in the original characteristics of the machine, may be done only by saint-gobain abrasives s.A. Who shall confirm that the machine is still in conformity with the safety regulations. Saint-gobain abrasives s.A. Keep...

  • Page 10

    10 2.2 layout made of jig welded open profile steel, the cs 451 is stable but at the same time, easily transportable. The one-piece blade guard (1) fully protects the operator and his working environment. It is firmly fixed to the main frame but can be opened by rotation to change blades. A manually...

  • Page 11

    11 the precisely manufactured blade shaft is fitted into two heavy-duty self-aligning pillow block bearings, including grease nipples. On one end is a poly-v pulley with taper lock and on the other end the shaft is reduced to 25,4mm, allowing an inner flange to be fixed. Outer flange is assembled on...

  • Page 12

    12 2.3 technical data engine honda gx390, 4 stroke, 1 cylinder, 13hp (9,6kw) fuel automotive unleaded gasoline with a pump octane rating of 86 or higher (research octane rating of 91 or higher) oil honda 4-stroke, or equivalent high detergent, premium quality motor oil certified to meet or exceed u....

  • Page 13

    13 2.4 vibration emission declaration declared vibration emission value in accordance with en 12096 machine model / code measured vibration emission value a m/s 2 uncertainty k m/s 2 tool used model / code cs 451 p13 70184628433 2.8 0.5 duo extreme Ø350x25.4mm 70184624580 • values determined accordi...

  • Page 14

    14 3 assembly and commissioning before beginning the work with the cs 451, you have to assemble some parts. 3.1 operator’s handle assembly secure the operator’s handle in a comfortable user position by using the locking screws. 3.2 tool assembly only norton blades with a maximum diameter of 450 mm c...

  • Page 15

    15 3.4 starting the machine make sure the blade is raised clear up the ground before starting the machine. Turn the fuel valve to the on position. Move the choke lever to the closed position. Note: do not use the choke if the engine is warm or the air temperature is high. Move the throttle control l...

  • Page 16

    16 4 transport and storing take the following measures in order to transport and store the cs 451 securely. 4.1 securing for transport before transporting the machine: • remove the blade. • empty the water tank. • lower the handle in its fixing tube and secure it using the locking screws. • raise th...

  • Page 17

    17 5 operating the cs 451 5.1 site of work before you start working, please check the following points: • remove from the site anything, which might hinder the working procedure. • make sure the site is sufficiently well lit. • place, when used, the water hose so that it can’t be damaged • make sure...

  • Page 18

    18 5.2.2 cutting the floor you can now start the engine. To make your cut, • turn the depth hand wheel until the blade slightly touches the floor. • open water valve to control the amount of water required for the type of blade, using 15 to 25l/min for wet cutting and 1-2l/min for dry cutting (dust ...

  • Page 19

    19 6 maintenance and service caution: to perform maintenance of the machine, always switch it off. Always wear a mask and safety goggles while performing the maintenance of machine. 6.1 maintenance of the machine to ensure a long-term quality from the cutting with the cs 451, please follow the maint...

  • Page 20

    20 6.2 maintenance of the engine regular service period perform at every indicated month or operating hour interval, whichever comes first e a c h u s e f ir s t m o n th o r 2 0 h o u rs e v e ry 3 m o n th s o r 5 0 h o u rs e v e ry 6 m o n th s o r 1 0 0 h o u rs check level engine oil change ch...

  • Page 21

    21 air cleaner cs 451 has a dual type filter. To service the air cleaner filter, remove the blade and the water tank from the machine, and drive the engine support in its lowest position using the hand wheel. Follow these instructions: • remove the nut, air cleaner cover and wing nut. • remove the p...

  • Page 22

    22 cyclone filter when the cyclone housing becomes dirty, unscrew the three special pan screws and wipe or wash the components with water. Next, thoroughly dry the components and carefully reassemble them. When reinstalling the cyclone, ensure that the tab on the air intake fits properly into the gr...

  • Page 23

    23 fuel line to service the fuel line, follow these instructions: • drain the fuel into a suitable container, and remove the fuel tank. • disconnect the fuel line, and unscrew the fuel filter from the tank. • clean the filter with solvent, and check, that the filter screen is undamaged. • place the ...

  • Page 24

    24 7 breakdowns: causes and cures 7.1 breakdown-finding procedures should any breakdown occur during the use of the machine, turn it off. Let only qualified staff make any intervention other than the ones described in the previous section. 7.2 trouble-shooting guide trouble possible source resolutio...

  • Page 25

    25 guarantee can be claimed and technical support obtained from your local distributor where machines, spare parts and consumables can be ordered as well: benelux and france: from saint-gobain abrasives in the grand-duché de luxembourg free telephone numbers: belgium : 0 800 18951 france: 0 800 90 6...

  • Page 26

    26.

  • Page 27

    27.

  • Page 28

    28 saint-gobain abrasives 190, bd john f. Kennedy l-4930 bascharage luxembourg tel.: ++352 50 401-1 fax: ++352 50 16 33 e-mail: sales.Nlx@saint-gobain.Com www.Construction.Norton.Eu 30.09.2008.