Summary of CTC701
Page 1
Owners manual 7” table top tile saw model:ctc701 form.
Page 2: Warranty
2 warranty norton warrants all products manufactured by it against defects in workmanship or materials for a period of one (1) year from the date of shipment to the customer. The responsibility of norton under this warranty is limited to replacement or repair of defective parts at norton's stephenvi...
Page 3: Table of Contents
3 table of contents contents page i. Ctc701 safety instructions 4-9 1. Basic safety instructions 4 1.1 symbols 4 1.2 safety precautions 5 1.3 dust and silica warning 6 1.4 safety instructions for working with the machine 7-9 2. Machine description 10-12 2.2 use of machine 10 2.3 layout 10-11 2.3 tec...
Page 4
4 i. Ctc701 safety instructions 1. Basic safety instructions the ctc701 is exclusively designed for the cutting of ceramic tiles, porcelain tiles, natural stone flooring materials, artificial stone flooring materials, and terracotta materials up to 2-1/4” (57mm). Uses other than the manufacturer's i...
Page 5
5 1.2 safety precautions important! The following safety precautions must always be observed. Additional warning/hazard symbols keep all guards in place when operating any piece of equipment keep hands, feet, hair, and clothing away from all rotating parts never tamper with the governor components o...
Page 6
6 1.3 dust and silica warning grinding/cutting/drilling of masonry, concrete, metal and other materials can generate dust, mists and fumes containing chemicals known to cause serious or fatal injury or illness, such as respiratory disease, cancer, birth defects or other reproductive harm. If you are...
Page 7
7 1.4 safety instructions for working with the machine before commencing work: • know your ctc701 tile cutting machine! Read the operator’s manual carefully. Learn the operation, application and limitations, as well as the specific potential hazards peculiar to this equipment and its usage. • before...
Page 8
8 • use only three-wire grounded extension cords suitable for use outdoors and of sufficient gage to accommodate power requirements. • ground the machine! The tile saw must be grounded while in use to protect the operator from electric shock. The motor is equipped with a three prong grounding type p...
Page 9
9 1. Before mounting any blade on the saw, the blade should be inspected for any damage which might have occurred during shipment, handling or previous use. 2. The blade collars and arbors should be cleaned and examined for damage before mounting the blade. 3. The blade must be properly fitted over ...
Page 10: 2. Machine Description
10 2. Machine description any modification, which could lead to a change in the original characteristics of the machine, may be done only by saint-gobain abrasives who shall confirm that the machine is still in conformity with the safety regulations. The ctc701 tile saw is designed for durability an...
Page 11
11 electrical motor and switch (3) motor with 1.07 hp (800w). The motor is designed to operate on 115-120 volts, 60 hz, single phase electrical circuits. Use a circuit with a 15 amp circuit breaker for best performance. The on-off switch also serves as emergency stop. Tilting table (4) the cutting t...
Page 12
12 2.3 technical specifications technical specifications ctc701 product number (upc) 70184630029 blade guard capacity - in (mm) 7" (177) maximum depth of cut - in (mm) 2-1/4" (57) arbor size - in (mm) 5/8" blade flange diameter - in (mm) 3 (78) blade shaft rpm 2,990 maximum material size - in (mm) 1...
Page 13
13 3.1 tool assembly only use norton clipper continuous rim blades with a maximum diameter of 7” (177mm) can be used with the ctc701. All tools used must be selected with regard to their maximum permitted cutting speed for the machine’s maximum permitted rotation speed. Before mounting a new blade i...
Page 14
14 • fill the water pan with clean water up to 3/16” (5mm) from the upper edge of the water tray. • ensure that water is delivered adequately to both sides of the blade, as insufficient water supply may result in premature failure of the diamond blade and is not covered by any warranty. • always mak...
Page 15
15 the table to align the guide. Then tighten it back. 5.3 general advice for cutting • only tiles with max. Dimensions of 15-3/4”x15-3/4”x1/4” (400x400x6mm) and max. Weight of 6-1/2 lbs (3kg) can be cut with the machine. • before beginning work make sure tools are firmly seated! • select the right ...
Page 16
16 6.3 cleaning of the machine your machine will last longer if you clean it thoroughly after each day of work, especially water pan, motor and blade flange. To clean disconnect the machine from the power source and wipe down the ctc701 with a damp cloth. 7. Trouble shooting 7.1 trouble shooting pro...
Page 17: 8. Parts List Section
17 8. Parts list section ordering information 1. List model number and serial number of machine. 2. List part number and serial number of part not the item number. 3. Wherever alternate parts are shown due to product improvement, inspect the part you have and provide additional description as necess...
Page 18
18 8.1 ctc701 service parts.
Page 19
19 8.1 ctc701 service parts pos part# upc# description qty req type(*) 1 243000 scr 2.9 x 13 phillips head 6 s 2 243001 gasket for power cable 1 w 3 243002 cover for capacitor box 1 s 4 243003 cable clamp 3 s 5 243004 gasket capacitor box 1 w 6 243005 scr 4 x 9 5 s 7 243006 securing strap for capaci...
Page 20
20 pos part# upc# description qty req type(*) 49 243046 slide w/slots guide-a-cut ctc701 1 s 50 243047 nut m4 din985 lock 1 s 51 243048 00310340199 cutting table ctc701 1 s 52 243049 blade guard left side ctc701 1 s 53 243050 scr m6 x 25 1.0 carriage 1 s 54 243051 bracket blade guard support ctc701 ...
Page 21
21 notes:.
Page 22
22.