Summary of TT 250 G
Page 1
Tt 250 g operating instructions.
Page 2
2.
Page 3: Declaration Of Conformity
3 the undersigned manufacturer: saint - gobain abrasives s.A. 190, bd j.F. Kennedy l- 4930 bascharage declares that this product: tile saw (code) tt 250 g 230v (70184625705) tt 250 g 230v uk (70184626965) tt 250 g 115v (70184627049) is in conformity with the following directives: • european machiner...
Page 4
4.
Page 5: Tt250G
5 tt250g operating instructions 1 basic safety instructions 6 1.1 symbols 6 1.2 machine plate 7 1.3 safety instructions for particular operating phases 7 2 machine description 8 2.1 short description 8 2.2 purpose of use 8 2.3 layout 8 2.4 technical data 9 3 assembly and commissioning 10 3.1 tool as...
Page 6
6 1 basic safety instructions the tt250g is exclusively designed for the cutting of tiles mainly on construction sites. Uses other than the manufacturer's instructions shall be considered as contravening the regulations. The manufacturer shall not be held responsible for any resulting damage. Any ri...
Page 7
7 1.2 machine plate important data can be found on the following plate located on the machine: 1.3 safety instructions for particular operating phases before commencing work • before commencing work, make yourself familiar with the working environment at the place of use. The working environment inc...
Page 8
8 2 machine description any modification, which could lead to a change in the original characteristics of the machine, may be done only by saint-gobain abrasives who shall confirm that the machine is still in conformity with the safety regulations. 2.1 short description the tt250g tile saw is design...
Page 9
9 blade guard (4) jig-welded steel construction with 250mm-diameter blade capacity, which offers maximum operator protection and increased visibility of the work piece. The guard is assembled on the frame. Guide-a-cut (5) the guide-a-cut can be adjusted to the desired cutting width. It is locked usi...
Page 10
10 3 assembly and commissioning the machine is delivered fully equipped. It is ready for operation after assembly the diamond blade, the blade guard and the guide-a-cut, and after connection to the appropriate power supply. 3.1 tool assembly only norton clipper continuous rim blades with a maximum d...
Page 11
11 3.2 blade guard assembly • the blade guard is not assembled in factory to prevent it from being damaged during transport. • assemble the blade guard on the support (1) 3.3 guide-a-cut assembly • put the guide-a-cut on the table. • screw the two locking screws. 3.4 electrical connections check tha...
Page 12
12 4 transport and storing 4.1 securing for transport before transporting the machine, always remove the blade and empty the water pan. 4.2 long period of inactivity if the machine is not going to be used for a long period, please take the following measures: • completely clean the machine • empty t...
Page 13
13 5 operating the machine 5.1 site of work 5.1.1 siting the machine • remove from the site anything, which might hinder the working procedure! • make sure the site is sufficiently well lit! • observe manufacturer's conditions for connecting to power supplies! • place electric cables in such a way t...
Page 14
14 6 maintenance and servicing to ensure a long-term quality from the cutting with the tt250g, please follow the maintenance plan below: b e g in o f th e d a y d u ri n g t h e c h a n g in g o f to o l e n d o f th e d a y o r m o re o ft e n i f re q u ir e d e v e ry w e e k a ft e r a f a u lt ...
Page 15
15 7 faults: causes and cures 7.1 fault-finding procedures should any fault occur during the use of the machine, turn it off, and isolate it from the electrical supply. Any works dealing with the electrical system or supply of the machine can only be carried out by a qualified electrician. 7.2 troub...
Page 16
16 7.3 circuit diagram.
Page 17
17 7.4 customer service when ordering spare parts, please mention: • the serial number (7 digits). • the code of the part. • the exact denomination. • the number of parts required. • the delivery address. • please indicate clearly the means of transportation required such as "express" or "by air". W...
Page 18
18 guarantee can be claimed and technical support obtained from your local distributor where machines, spare parts and consumables can be ordered as well: benelux and france: from saint-gobain abrasives s.A. Free telephone numbers: belgium : 0 800 18951 france: 0 800 90 69 03 holland: 0 8000 22 02 7...
Page 19
19.
Page 20
20 saint-gobain abrasives 190, bd. J. F. Kennedy l-4930 bascharage luxembourg tel.: ++352 50401-1 fax: ++352 501633 e-mail: sales.Nlx@saint-gobain.Com www.Construction.Norton.Eu 08.12.2008.