Nortron B SERIES Installation And Operating Instructions Manual
30042431A
B SERIES ELECTRIC FURNACE
TEL.: 905-670-2500
FAX: 905-795-8311
CUSTOMER SERVICE TEL.: 1-888-882-7626
MISSISSAUGA, ONTARIO L5T 1H9
• Never tamper with the unit or its controls. User MUST contact
a specialized contractor when a failure occurs. DO NOT
ATTEMPT to repair.
• When using a humidifier make sure not to damage the heating
element bank.
• We recommend that your unit be inspected by a specialized
technician once a year.
• Poor maintenance of air filters OR an unbalanced static
pressure may result in a performance decrease.
• Always use genuine parts for maintenance or service call.
The use of unbranded parts will void the warranty.
• The use of this unit without an air distribution duct will void
the warranty.
• It is strictly forbidden to use jumpers to simulate heat demand.
• Risk of electrical shock. Disconnect power before installation,
servicing, maintenance or field wiring. Replace all panels
before operating. Failure to do so can result in electrical
shock causing severe injuries or death.
• When performing installation, servicing or cleaning the unit,
it is recommended to wear safety glasses and gloves.
• To assure a proper performance of your furnace, we recommend
that you use high quality name brand thermostats.
• When applicable local regulation comprises more restrictive
installation and/or certification requirements, the aforementioned
requirements prevail on those of this document and the
installer agrees to conform to these at his own expenses.
• For your safety, do not store or use gasoline or other flammable
liquids and vapors in the vicinity of this unit or any other
appliance.
• These instructions are intended to be used by qualified personnel
who have been trained in installing this type of furnace.
Installation of this furnace by an unqualified person may
lead to equipment damage and/or hazardous condition
which may lead to bodily harm.
• This furnace is not watertight and is not designed for outdoor
installation. This furnace shall be installed in such a manner
as to protect its electrical components from water. Outdoor
installation leads to a hazardous electrical condition and to
premature furnace failure, thus voiding the warranty.
• Do not block the combustion air openings in the furnace.
Any blockage will result in improper overheat situation and
may result in a fire hazard and/or cause bodily harm.
• The unit must have an uninterrupted or unbroken electrical
ground to minimize personal injury if an electrical fault
should occur. When performing electrical connection, the
ground conductor must be firmly attached to the ground lug
in the furnace.
• Do not use this furnace as a construction heater. Use of this
furnace as a construction heater exposes the furnace to
abnormal conditions, contaminated combustion air and the
lack of air filters. Failure to follow this warning can lead to
premature furnace failure and/or vent failure which could
result in a fire hazard and/or bodily harm.
• The owner and/or the user is responsible of the following:
Always maintain the immediate surrounding of the furnace
free from combustible and highly flammables materials.The
furnace ambient air should not have an excessive dust
concentration and humidity. Never operate this central heating
appliance without an air filter.
• Before performing any service functions, unless operations
specifically require the power to be on, make sure all utilities
are turned “OFF” upstream of the appliance. Failure to comply
with this warning will cause a fire hazard and/or bodily
harm.
• All questions regarding the operation, maintenance or warranty
of this unit should be addressed to the company where this
product has been sold from.
WARNING
!
IMPORTANT: READ AND SAVE THESE INSTRUCTIONS.
CAUTION
• Never burn garbage or paper in the heating system and never leave rags or paper around the unit.
• Return air grilles and warm air registers must not be obstructed.
IMPORTANT: All local and national code requirements governing the electrical installation heating equipment, wiring and flue connections
must be followed. Some of the codes that may be applicable are :
ANSI/NFPA 70 NATIONAL ELECTRICAL CODE
CSA C22.1 CANADIAN ELECTRICAL CODE
Only the latest issues of the above codes should be used, and are available from either:
The National Fire Protection Agency
Batterymarch Park
Quincy, MA 02269
The Canadian Standards Association
178 Rexdale Blvd.
Rexdale, Ontario M9W 1R3
or