- DL manuals
- Oakton
- Multimeter
- 35632-Series
- Operating instructions manual
Oakton 35632-Series Operating instructions manual
Summary of 35632-Series
Page 1
Operating instructions oakton ® 35632-series portable waterproof ph/dissolved oxygen meter ph/dissolved oxygen/ ° c/ ° f meter ph/do 300 series waterproof mode hold enter on off cal meas ▲ ▼ setup atc ready meas c % ip 67 notes write down the name and information of your oakton distributor here..
Page 2
3 2 table of contents 1. Introduction............................................................................................4 2. Display and keypad functions .............................................................5-6 2.1 display ...............................................................
Page 3
5 4 1. Introduction thank you for selecting an oakton meter. This oakton portable meter is a microprocessor-based instrument that measures ph, dissolved oxygen and temperature. It’s completely waterproof—and it floats! Your meter has many user-friendly features, all of which are accessible through t...
Page 4
7 6 keypad the large membrane keypad makes the instrument easy to use. Each button, when pressed, has a corresponding graphic indicator on the lcd. On/off ............Powers and shuts off the meter. Hold ..............Freezes the measured reading. To activate, press hold while in measurement mode. T...
Page 5
9 8 to connect the ph electrode: 1. Slide the bnc connector of the probe over the bnc connector socket on the meter. Make sure the slots of the connector are in line with the posts of the socket. Rotate and push the connector clockwise until it locks. See figure below. 2. To remove probe, push and r...
Page 6
11 10 for directions on how to calibrate your meter: • see sections 4.2-4.3 on pages 11-13 for ph calibration • see section 4.4-4.5 on page 14-16 for % saturation calibration • see section 4.4 and 4.6 on page 14, 17-18 for mg/l (ppm) calibration • see section 4.7 on pages 19 for temperature calibrat...
Page 7
13 12 6. Press enter to confirm calibration . The meter is now calibrated to the current buffer. See figure • if you are performing multipoint calibration, go to step 7. • if you are performing one-point calibration, go to step 9. 7. Rinse the probe with de-ionized water or a rinse solution, and pla...
Page 8
Dissolved oxygen calibration in percent saturation you can calibrate this meter quickly and easily in air. The exact calibration value depends on barometric pressure. The meter is set to a factory default of 760 mm hg, which results in a calibration value of 100% saturation in air. Note: if the baro...
Page 9
Dissolved oxygen calibration in mg/l (ppm) mode calibrating the meter to 100 % in saturation mode will also calibrate the mg/l mode at the value in mg/l corresponding to 100% saturation. This should produce acceptable results in most applications. This meter also lets you make a calibration adjustme...
Page 10
19 18 notes on mg/l (ppm) mode calibration during mg/l (ppm) calibration, the meter adjusts to the barometric pressure value that is programmed into the meter. It also adjusts to the salinity value that is programmed into the meter. You can change the barometric pressure value and salinity value in ...
Page 11
21 20 5. Measurement taking do readings during measurement, the probe can be: • fully immersed in the solution • partially immersed in the solution do not allow the probe’s membrane surface to touch anything! The probe guard (the piece with holes fitted over the end of the probe) protects the membra...
Page 12
23 22 salinity adjustment note: this mode appears in mg/l (ppm) measurement mode only. 1. Press the mode key to select mg/l (ppm) mode. 2. Press the setup key to enter set up mode. See figure 4. Press the enter key until the upper display shows a number and the lower display shows “sal”. 5. Use the ...
Page 13
24 25 taking measurements with ready indicator selected on if the ready indicator has been activated, the ready annunciator lights when the reading is stable. Switch the ready indicator on or off in set up program p3.1— see page 35 for directions. Taking measurements with the auto endpoint feature s...
Page 14
27 26 using the backlit lcd this feature lets you view readings in low light situations. 1. To activate the backlit lcd feature, press the key to activate. See figure to keep the lcd backlit, keep the key pressed. If the key is not pressed, the backlight automatically shuts off automatically after 2...
Page 15
29 28 8. Advanced setup functions the advanced set up mode lets you customize your meter’s preferences and defaults. Your oakton waterproof meter features different sub groups that organize all setup parameters. This meter displays different subgroups depending on which mode the meter is in: ph setu...
Page 16
From the % saturation measurement mode dpr: dissolved oxygen parameters • select hg or pa barometric pressure units • select barometric pressure cal: viewing previous calibration data • view previous calibration data ofs: % saturation offset adjustment • set % saturation offset adjustment ele: viewi...
Page 17
32 33 from measurement mode: 1. Press the mode key to select ph measurement mode. 2. Press the setup key to enter setup mode. See figure 3. Press the ▲ and ▼ keys to scroll through subgroups until you view parameter p1.0. 4. Press the enter key repeatedly to view previous calibration data. P1.1 = ph...
Page 18
35 34 ph setup d d setup % ph e e p2.2: electrode slope note: this parameter is available in ph measurement mode only. From measurement mode: 1. If necessary, press the mode key to select ph measurement mode. Press the setup key to enter setup mode. 2. Press the ▲ and ▼ keys to scroll through subgro...
Page 19
37 36 from measurement mode: 1. Press the mode key to select ph measurement mode. 2. Press setup key to enter setup mode. 3. Press the ▲ and ▼ keys to scroll through subgroups until you view parameter p3.0. See figure 4. Press the enter key twice to select parameter p3.2. See figure 5. Press the ▲ a...
Page 20
39 38 ph mode—p4.0: resetting to factory default settings this program lets you reset all ph parameters to factory default settings. This clears all calibration data any other ph setup functions you might have changed. The following settings will remain as you have set them: • temperature unit of me...
Page 21
41 40 % saturation mode—p2.0: offset adjustment use the offset adjustment to act as an offset at values between 0 and 100%. It is useful to match against end-user standards (i.E. A test kit value). 8.7 from measurement mode: 1. Press the mode key to select % saturation mode. 2. Press the setup key t...
Page 22
43 42 from measurement mode: 1. Press the mode key to select the % saturation measurement mode. 2. Press the setup key to enter setup mode. 3. Press the ▲ and ▼ keys to scroll through subgroups until you view parameter p4.0 in the lower display. See figure 4. Press the enter key. The upper display s...
Page 23
45 44 p5.2: selecting °c or °f temperature readout this meter lets you select between °c and °f units for temperature readings. From measurement mode: 1. Press the mode key to select the % saturation measurement mode. 2. Press setup key to enter setup mode. 3. Press the ▲ and ▼ keys to scroll throug...
Page 24
47 46 % saturation mode—p7.0: resetting to factory default settings this program lets you reset all parameters to factory default settings. This clears all calibration data, memory, and any other setup functions you might have changed. The lcd contrast setting will be reset to 8 (the maximum setting...
Page 25
49 48 p1.2 salinity adjustment mode salinity correction mode lets you correct for the variations in oxygen solubility due to salt concentration in the sample. From measurement mode: 1. Press the mode key to select mg/l (ppm) mode. 2. Press the setup key to enter setup mode. 3. Press the ▲ and ▼ keys...
Page 26
51 50 from measurement mode: 1. Press the mode key to select the mg/l (ppm) measurement mode. 2. Press the setup key to enter setup mode. 3. Press the ▲ and ▼ keys to scroll through subgroups until you view parameter p3.0 in the lower display. See figure 4. Press the enter key. The upper display sho...
Page 27
53 52 from measurement mode: 1. Press the mode key to select mg/l (ppm) mode. 2. Press setup key to enter setup mode. 3. Press the ▲ and ▼ keys to scroll through subgroups until you view parameter p4.0 in the lower display. See figure 4. Press the enter key until “do” appears in the upper display, p...
Page 28
55 54 mg/l (ppm) mode——p5.0: adjusting lcd brightness this mode lets you adjust the brightness of the backlit lcd. Selecting a dimmer backlighting level helps conserve batteries. 8.17 from measurement mode: 1. Press the mode key to select mg/l (ppm) mode. 2. Press setup key to enter setup mode. 3. P...
Page 29
57 56 do probe care the probe is a galvanic measuring element which produces an output proportional to the oxygen present in the medium in which it is placed. The galvanic probe design lets you take measure- ments immediately—without the typical 15 minute wait of other dissolved oxygen probes. The p...
Page 30
59 58 do membrane replacement replacement of the membrane is required only when you cannot calibrate the probe, or if the membrane is damaged. Typical membrane damages are punctures or wrinkles caused during measurements or cleaning. To order replacement probe components or a replacement probe, see ...
Page 31
61 60 do electrolyte solution the electrolyte solution in your probe’s cap will periodically evaporate and need to be replaced. 35640-71 replacement electrolyte solution comes premixed and ready to use. However, the electrolyte mixture package 35640-70 has a longer shelf life in its unmixed form. If...
Page 32
63 62 11. Error messages lcd indicates cause solution display err unrecognized input wrong input in release key. Select annunciator from keypad selected mode. Valid operations depending on mode. Cal & err calibration error wrong value input check your input value, annunciators at calibration. Clean ...
Page 33
65 64 13. Accessories meters 35632-02 ph/do 300 meter meter only 35632-00 ph/do 300 meter includes do probe with 10-ft cable (35640-50), ph elec- trode with 10-ft cable (35805-23), and electrolyte solution 35632-60 ph/do meter kit. Includes ph/do meter plus do probe with 10-ft cable, ph electrode wi...
Page 34
67 66 14. Appendix 1: meter theory dissolved oxygen levels in natural and waste waters depend on the physical, chemical, and biochemical activities in the water body. This meter uses a galvanic probe. It consists of a cell that contains electrolyte and that is enclosed by a selective membrane, and t...
Page 35
69 68 17. Warranty oakton warrants this meter to be free from significant deviations in material and workmanship for a period of three years from date of purchase. Oakton warrants this probe to be free from significant deviations in material and workmanship for a period of six months from date of pu...