1. DL manuals
  2. Oasis
  3. Control Unit
  4. SV103
  5. Instruction Manual

Oasis SV103 Instruction Manual

Manual is about: SV100 Series Actuated Sandwich Valve

Summary of SV103

  • Page 1

    Oasis engineering ltd 129 birch avenue, tauranga, new zealand. T: +64 7 928 3808 f: +64 7 928 3809 e: info@oasisngv.Com w: www.Oasisngv.Com sv100 series actuated sandwich valve instruction manual failure to follow these instructions or to properly install and maintain this equipment could result in ...

  • Page 2: Safety

    2 we reserve the right to modify product specifications without prior notice. Sv-ins-02 3317 © oasis engineering limited safety warning! High pressure gas and gas equipment can cause serious harm to both infrastructure and personnel if safety precautions are not followed. Oasis recommends considerin...

  • Page 3: Tools Required

    3 we reserve the right to modify product specifications without prior notice. Sv-ins-02 3317 © oasis engineering limited tools required silicone grease (rocol mx22 or similar) for all o-rings torque wrench important oasis recommends the use of class 12.9 plain black socket head cap screws with this ...

  • Page 4: Installation Instructions

    4 we reserve the right to modify product specifications without prior notice. Sv-ins-02 3317 © oasis engineering limited installation instructions 1. Grease o-rings. 2. Insert o rings into grooves. 4. Place valve into position. 3. Line valve up with end caps. 6. Torque bolts. 5. Insert bolts. Torque...

  • Page 5: Installation Instructions

    5 we reserve the right to modify product specifications without prior notice. Sv-ins-02 3317 © oasis engineering limited installation instructions 7. Install drive dog. 9. Insert bracket screws. 8. Install actuator and bracket. 10. Tighten bracket screws. 11. Install complete, check for leaks on fir...

  • Page 6: Operation Instructions

    6 we reserve the right to modify product specifications without prior notice. Sv-ins-02 3317 © oasis engineering limited 1. Connect air line and check connections for leaks. For oasis standard actuators the left port is the inlet port used to activate the actuator. Do not operate the actuator with s...

  • Page 7: Seal Kit Parts

    7 we reserve the right to modify product specifications without prior notice. Sv-ins-02 3317 © oasis engineering limited seal kit parts sv103 - sv104** sv106** — sv108** (sv103 - 022 nitrile 90) (sv104 - 025 nitrile 90) (sv106 - 131 nitrile 90) (sv108 - 138 nitrile 90) 2 x seats 1 x stem 1 x ball 1 ...

  • Page 8: Servicing - Disassembly

    8 we reserve the right to modify product specifications without prior notice. Sv-ins-02 3317 © oasis engineering limited servicing - disassembly 4. Unscrew and remove end cap. 5. Discard the seat. 6. Discard the ball. 3. Remove nut, locking tab and gland. 2. Release the nut locking tab. 1. Remove th...

  • Page 9: Servicing - Disassembly

    9 we reserve the right to modify product specifications without prior notice. Sv-ins-02 3317 © oasis engineering limited servicing - disassembly 7. Remove 2nd seat and discard. 9. Clean components and inspect for damage. Sv103 sv104 - sv106 - sv108 8. Remove 2nd seat and discard. 7. Remove stem. Do ...

  • Page 10: Servicing - Assembly

    10 we reserve the right to modify product specifications without prior notice. Sv-ins-02 3317 © oasis engineering limited servicing - assembly 1. Insert seat first. Sv103 1. Insert stem assembly first. Click 2. Insert seat. A b sv104 - sv106 - sv108 3. Insert ball. Click 2. Insert stem assembly..

  • Page 11: Servicing - Assembly

    11 we reserve the right to modify product specifications without prior notice. Sv-ins-02 3317 © oasis engineering limited servicing - assembly 4. Insert 2nd seat. A b 5. Apply anti seize to cap. Sv106 - sv108 5. Fit new o-rings and back-up to end cap. Sv103 - sv104 6. Tighten end cap. Recommended en...

  • Page 12: Servicing - Assembly

    12 we reserve the right to modify product specifications without prior notice. Sv-ins-02 3317 © oasis engineering limited servicing - assembly 9. Bend locking tab & lock the nut. 8. Torque stem nut. 11. Install seal face o-rings. 12. Done! Follow installation instructions on page 3 to refit sandwich...