Summary of 7055
Page 1
Océ 7055/7056 user manual n.
Page 2: Océ-Technologies B.V.
Copyright océ-technologies b.V. Venlo, the netherlands © 1998 all rights reserved. No part of this work may be reproduced, copied, adapted, or transmitted in any form or by any means without written permission from océ. Océ-technologies b.V. Makes no representation or warranties with respect to the ...
Page 3
Contents 3 contents chapter 1 introduction the océ 7055/7056 6 the operating panel 7 stand-by mode 7 buttons and functions 7 display 8 switching on/off 9 chapter 2 copy jobs introduction 12 making copies 13 special settings 19 exposure setting 19 trailing edge and leading edge 20 making a test strip...
Page 4
4 océ 7055/7056 user manual appendix a overview and tables standard settings 46 standard operating mode 47 product specifications 48 roomtemperature (t) and relative humidity (rh) 48 originals that can be used 49 copy material that can be used 50 appendix b safety information instructions for safe u...
Page 5
5 océ 7055/7056 user manual chapter 1 introduction this chapter contains a general description of the océ 7055/7056 and how to get the copier ready to copy..
Page 6
6 océ 7055/7056 user manual the océ 7055/7056 the océ 7055/7056 is a copier for large documents (e.G. Architectural or engineering drawings). The machine is easy to use and makes copies on paper, transparent, vellum or polyester film with the quality and reliability that one might expect from océ. T...
Page 7
Introduction 7 the operating panel stand-by mode the operating panel (see the illustration on inside back cover) on the océ 7055/7056 is easy to use and specially designed to carry out copy jobs. After switching on, (see page 9), the machine is always ready for operation: the display shows blinking ...
Page 8
8 océ 7055/7056 user manual copy quantity selection button press these buttons to increase or decrease the number of copies. The copy quantity can be changed at all times. Correction button resets the copy quantity counter to ‘1’. By pressing the correction button twice, all settings will reset to t...
Page 9
Introduction 9 switching on/off after switching on the machine is ready for operation. The display shows blinking leds. In this state, the operating panel is in stand-by mode. After you have switched on the machine, there is no need to switch it off after each copy job. You can leave the machine swi...
Page 10
10 océ 7055/7056 user manual.
Page 11
11 océ 7055/7056 user manual chapter 2 copy jobs making copies and special settings.
Page 12
12 océ 7055/7056 user manual introduction with the océ 7055/7056, you can make copies on paper, transparent, vellum or polyester film. You can select between manual feed and automatic feed by pressing the copy material input button. When automatic feed is selected, the copy material is taken from th...
Page 13
Copy jobs 13 making copies when you use the manual feed option, you can always feed the original or the copy material. The copying process only starts after pressing the ‘start’ button. Before pressing the ‘start’ button, you can control and change the settings. When you use the automatic feed optio...
Page 14
14 océ 7055/7056 user manual 3 press the operating mode button to toggle between synchro cut mode and standard mode. Synchro cut mode is selected by default. ■ in synchro cut mode, the copy is cut at the length of the original. ■ in standard mode, the copy is cut at a standard length. You select the...
Page 15
Copy jobs 15 5 press the start button. The copies are made and cut at the appropriate length. After the job is completed the copy counter is set to 0. If you want to make more copies of the same original, you don’t have to feed the original again as long as you haven’t pulled it from the original fe...
Page 16
16 océ 7055/7056 user manual note: changing the copy quantity can be done at all times. When you make a mistake you simply press the correction button to correct the copy quantity. [4] setting more than one copy using the ‘+’ or ‘-’ button 4 feed the original centrally and face down into the origina...
Page 17
Copy jobs 17 attention: strongly curled originals have to be fed in carefully. In certain circumstances the copier can pull the original in. [5] feeding an original note: minimum length of the copy material is 420 mm. 5 feed a sheet of copy material, in line with the original, into the copy feed tab...
Page 18
18 océ 7055/7056 user manual attention: if sheets of copy material are curled, feed them with the curl facing down. [6] feeding the copy materialmakemore copies of 6 press the start button. The copy will now be made and the copy quantity counter decreases by one. After the job is completed the copy ...
Page 19
Copy jobs 19 special settings exposure setting when copying extremely light or dark originals, or originals with unequal background density, the result may not meet your requirements (e.G. Too much background). In such cases you can adjust the exposure level. In the default setting the exposure leve...
Page 20
20 océ 7055/7056 user manual trailing edge and leading edge assume that you are working in automatic feed mode and your original has a filing strip. If you don’t want the filing strip to show on the copy, it is possible to create an edge. Make sure that the filing strip is at the trailing edge of th...
Page 21
Copy jobs 21 ▼ ▼ ▼ ▼ adjusting the edge 1 press the edge selection button to toggle between leading edge and trailing edge (see figure 9 for an example). The length display shows the length of the currently selected edge. [9] trailing edge buttons 2 press the edge adjustment buttons to change the si...
Page 22
22 océ 7055/7056 user manual making a test strip in some cases you want to check the exposure settings and the quality without wasting a complete copy. If this is the case, you can make a test strip. A small part of the original is copied on a strip. This test strip is cut the minimum length of 420 ...
Page 23
23 océ 7055/7056 user manual chapter 3 materials this chapter describes how to insert a new copy material roll, how to add toner and how to clean the transparent platen..
Page 24
24 océ 7055/7056 user manual inserting a new copy material roll if the paper path indicator flashes and the display shows error message e5, then you have to insert a new copy material roll. ▼ ▼ ▼ ▼ inserting a new material roll in the drawer section (roll 1) 1 pull the drawer section open by using t...
Page 25
Materials 25 2 remove the roll holder from the drawer. (see figure 12) 2488 [12] removing the roll holder from the drawer section 3 remove the cardboard core from the roll holder. 4 place the new roll of copy material on a table. 2486.
Page 26
26 océ 7055/7056 user manual 5 slide the roll holder in the new roll of copy material while pressing the knob. (see figure 13) [13] pressing the knob 6 align the copy material roll with the appropriate lines on the roll holder while pressing the knob. 2485.
Page 27
Materials 27 7 reposition the roll holder with the copy material in the drawer. (see figure 14) [14] repositioning the roll 8 feed the copy material as is shown in 15 on page 27. Use your thumbs to feed the copy material with the rollers. The arrow on the sticker indicates how far you have to feed t...
Page 28
28 océ 7055/7056 user manual 10 close the drawer. ▼ ▼ ▼ ▼ inserting a new material roll in the flap section (roll 2) note: this section is only intended for the océ 7056. 1 pull the flap section open by using the two catches. (see figure 16) [16] opening the flap section 2488.
Page 29
Materials 29 2 remove the roll holder. (see figure 17) [17] removing the tube from the flap section 3 remove the cardboard core from the roll holder. 4 place a new roll of copy material on a table. 2488 5 slide the roll holder in the roll of copy material while pressing the knob. (see figure 13 on p...
Page 30
30 océ 7055/7056 user manual 7 reposition the roll holder with the copy material roll in the drawer and feed the copy material (see figure 14 on page 27). Use your thumbs to feed the copy material with the rollers. The arrow on the sticker indicates how far you have to feed the copy material. [19] r...
Page 31
Materials 31 programming roll specifications if you have inserted a new roll with another copy material or with a different width, you have to program the océ 7055/7056. Programming the roll specifications implies that you instruct the machine of the specifications of the copy material on the rolls....
Page 32
32 océ 7055/7056 user manual adding toner if the toner level is low, the ‘add toner’ indicator starts flashing. You can finish your job. Then add toner. Attention: if you ignore this symbol, copy quality will diminish. ▼ ▼ ▼ ▼ adding toner attention: only use b1 toner. 1 switch off the copier. 2 uns...
Page 33
Materials 33 4 screw in the bottle clockwise in a slanted position (see figure 21). [21] screwing in the bottle 5 move the toner bottle to a vertical position ( see figure 21 and 22 ). [22] adding toner 6 when the toner bottle is empty return the bottle to the original position. 7 unscrew the toner ...
Page 34
34 océ 7055/7056 user manual ▼ ▼ ▼ ▼ replacing the waste toner bag 8 pull the waste toner bag from the holder and place the cap provided on the bag (see figure 23). [23] replacing the waste toner bag 9 slide a new waste toner bag over the holder. 10 close the cover and tighten the knurled nut. 11 sw...
Page 35
Materials 35 cleaning the transparent platen if the transparent platen is dirty or static it should be cleaned to ensure top quality copies. At the same time you can clean the white pressure platen attention: to achieve the best results, we recommend the use of océ cleaner ‘a’. (codenr. 1068117; cle...
Page 36
36 océ 7055/7056 user manual 3 clean the transparent platen and the white pressure platen with a soft cloth moistened with a small quantity “cleaner a”. For safety information see the safety data sheet in appendix b. [25] cleaning the transparent platen and the white pressure platen attention: make ...
Page 37
37 océ 7055/7056 user manual chapter 4 solving problems this chapter contains information on how to proceed incase a problem arises..
Page 38
38 océ 7055/7056 user manual introduction this chapter documents problems that may occur with the océ 7055/7056 and how to solve them. When an error occurs, the operating panel informs you about the nature of the problem. ■ if the paper path indicator flashes, a paper jam has occurred (see ‘clearing...
Page 39
Solving problems 39 operator recoverable errors when the copier detects an error, the copier stops immediately. The paper path indicator will lit and the length display shows an error code. The following explains the general procedure in case of an operator recoverable error ▼ ▼ ▼ ▼ general procedur...
Page 40
40 océ 7055/7056 user manual machine errors ▼ ▼ ▼ ▼ solving a machine error 1 switch off the copier and check the complete paper path (see page 41 and page 42). 2 then switch it on again. If no error number is shown on the length display, you can continue copying. If the machine error maintains, the...
Page 41
Solving problems 41 clearing original jams when during copying an original jam occurs, the paper path indicator will start flashing and the display shows the error message e0. ▼ ▼ ▼ ▼ clearing an original jam 1 switch off the copier. 2 first try to remove the jammed original by pulling it gently tow...
Page 42
42 océ 7055/7056 user manual clearing paper jams when paper feeds incorrectly, the paper path indicator will flash. ▼ ▼ ▼ ▼ clearing a paper jam in the copy material feed section 1 switch off the copier. 2 lower the copy feed table, using the two catches on the front underneath the copy feed table (...
Page 43
Solving problems 43 if the paper jam can not be cleared by opening the copy feed table than open the fusing section by: 1 switch off the copier. 2 unscrew the knurled nut at the left hand side of the machine and open the cover (see figure 28). [28] opening the left cover at the rear of the machine 3...
Page 44
44 océ 7055/7056 user manual 4 remove the jammed copy material. Attention: be careful! The toner is not fused. Note: check thoroughly that no scraps of material are left behind. 5 lift the green handle and close the fuser unit. 6 close the left cover and screw the knurled nut. 7 switch on the copier...
Page 45
45 océ 7055/7056 user manual appendix a overview and tables.
Page 46
46 océ 7055/7056 user manual standard settings on delivery the océ 7055/7056 is configured with a number of standard settings. Standard settings océ 7055/7056 exposure level 0 copy material paper trailing edge 0 mm leading edge 0 mm copy quantity 1 copy material roll 1 operating mode synchro cut.
Page 47
Overview and tables 47 standard operating mode when standard operating mode selected, the copy is cut at a pre-set standard length. Nine different settings are available by selecting standard operating mode and pressing the selection buttons. The following settings are possible: ■ 1189 mm ■ 841 mm ■...
Page 48
48 océ 7055/7056 user manual product specifications for more information about product specifications refer to the océ 7055/7056 safety data sheet in appendix b. Roomtemperature (t) and relative humidity (rh) a: machine specifications are applicable for the following conditions. B: copy quality not ...
Page 49
Overview and tables 49 originals that can be used curls > Ø 75mm without help of operator paste ups paste ups should be pasted 100% at all edges or in carrier sheet filing strips may be present at all edges of the original. Maximum size of hole: Ø 36 mm borders punching holes, reinforcement borders ...
Page 50
50 océ 7055/7056 user manual copy material that can be used océ copy machines and materials are matched for optimal quality and performance. It is therefore recommended to use only approved océ materials in the océ 7055/7056. A full list of océ materials suited for use in the océ 7055/7056, includin...
Page 51
Overview and tables 51 good: means fully recommended acceptable: means acceptable for limited performance not suitable: means not suitable at all compatibility review media materials weight judgement remark opaque pa- per 75 g/m 2 good opaque pa- per 110 g/m 2 acceptable guaranteed upto 50% rh eco p...
Page 52
52 océ 7055/7056 user manual.
Page 53
53 océ 7055/7056 user manual appendix b safety information.
Page 54
54 océ 7055/7056 user manual instructions for safe use océ designed products have been tested in accordance with the strictest international safety standards. To help assure safe working with these products it is important that you observe the following safety rules: maintenance ■ do not remove any ...
Page 55
Safety information 55 surroundings ■ do not block the ventilation openings of the machine. ■ ensure that the machine is placed on a level, horizontal surface of sufficient strength. See the océ 7055/7056 safety data sheet in this appendix for information about the weight of the equipment. ■ ensure t...
Page 56
56 océ 7055/7056 user manual mains core colours as the colours of the cores in the mains lead of this equipment may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: ■ the core which is coloured green and yellow must be connected to the terminal in...
Page 57
Safety information 57 safety data sheets the disclaimer below is valid for all safety data sheets in this manual. For questions about océ products regarding health, safety and environment, please contact your océ organisation; you can find the address in the last appendix of this manual. Disclaimer ...
Page 58
58 océ 7055/7056 user manual safety data sheets océ 7055/7056. The content of this safety data sheet is subject to the disclaimer on page 57 of this manual. Product safety data sheet océ-(uk), ltd number e-664-c-uk united kingdom date november 1997 copyright © 1995 océ-technologies b.V., venlo, nl m...
Page 59
Safety information 59 safety data sheet océ opc drum continued on the next page material safety data sheet number e-192-b-uk (93/112/eec and iso 11014-1) date july 1997 page 1 of 2 océ opc drum part no. 2912571 1. Product and company identification product name océ opc drum part no. 2912571 (for océ...
Page 60
60 océ 7055/7056 user manual the content of this safety data sheet is subject to the disclaimer on page 57 of this manual. Material safety data sheet number e-192-b-uk (93/112/eec and iso 11014-1) date july 1997 page 2 of 2 océ opc drum part no. 2912571 9. Physical and chemical properties appearance...
Page 61
Safety information 61 safety data sheet océ b1 toner continued on the next page material safety data sheet number e-180-b-uk (93/112/eec and iso 11014-1) date july 1997 page 1 of 2 océ b1 toner 1. Product and company identification product name océ b1 toner packing polyethylene bottle, contents 0,4 ...
Page 62
62 océ 7055/7056 user manual the content of this safety data sheet is subject to the disclaimer on page 57 of this manual. Material safety data sheet number e-180-b-uk (93/112/eec and iso 11014-1) date july 1997 page 2 of 2 océ b1 toner 9. Physical and chemical properties appearance and odour black ...
Page 63
Safety information 63 safety data sheet océ cleaner a continued on the next page number: e-104-a-nl language: english safety data sheet commercial product name packing use océ cleaner a, part no. 1068104 polyethylene bottle, contents 100 ml antistatic cleaning and maintenance ?Uid for glass surfaces...
Page 64
64 océ 7055/7056 user manual the content of this safety data sheet is subject to the disclaimer on page 57 of this manual. Number: e-104-a-nl language: english safety data sheet commercial product name océ cleaner a, part no. 1068104 5 protective measures, storage and handling 5.1 technical protecti...
Page 65
Safety information 65 safety data sheet océ developer continued on the next page material safety data sheet number e-181-b-uk (93/112/eec and iso 11014-1) date july 1997 page 1 of 2 océ d1 developer 1. Product and company identification product name océ d1 developer packing polyethylene bottle, cont...
Page 66
66 océ 7055/7056 user manual the content of this safety data sheet is subject to the disclaimer on page 57 of this manual. Material safety data sheet number e-181-b-uk (93/112/eec and iso 11014-1) date july 1997 page 2 of 2 océ d1 developer 9. Physical and chemical properties appearance and odour bl...
Page 67
Safety information 67 epa energy star ® océ-technologies b.V. Has joined the energy star ® program of the united states environmental protection agency (epa). The purpose of the energy star ® program is to promote the manufacturing and marketing of energy-efficient equipment, thereby potentially red...
Page 68
68 océ 7055/7056 user manual.
Page 69
69 océ 7055/7056 user manual appendix c miscellaneous.
Page 70
70 océ 7055/7056 user manual notation conventions there are a number of notation conventions used in this manual. This consistent style enables you to quickly become conversant with the use of this manual and consequently the océ 7055/7056. Description each section or subsection contains a descripti...
Page 71
Miscellaneous 71 reader’s comment sheet have you found this manual to be accurate? ❏ yes ❏ no could you operate the product after reading this manual? ❏ yes ❏ no does this manual provide enough background information? ❏ yes ❏ no is the format of this manual convenient in size, readability and arrang...
Page 72
72 océ 7055/7056 user manual comments: -------------------------------------------------------------------------------------------- -------------------------------------------------------------------------------------------- ---------------------------------------------------------------------------...
Page 73
Miscellaneous 73 addresses of local océ organisations océ-australia ltd. P.O.Box 363 ferntree gully mdc vic 3165 australia océ-Österreich gmbh postfach 95 1233 vienna austria océ-belgium n.V./s.A. Avenue j.Bordetlaan 32 1140 brussels belgium océ-brasil comércio e industria ltda. Caixa postal 3187 01...
Page 74
74 océ 7055/7056 user manual océ-nederland b.V. P.O.Box 800 5201 av ‘s-hertogenbosch the netherlands océ norge a/s postboks 53, grefsen 0409 oslo 4 norway océ-poland ltd. Ul. Lopuszànska 53 02-0232 warszawa poland océ-lima mayer s.A. Av. José gomes ferreira, 11 ed. Atlas ii miraflores 1495 algés por...
Page 75
Index 75 index a add toner’ indicator 32 adding toner 32 c cleaner a 36 cleaning the transparent platen 35 copy feed table 42 copy material 7 copy material input button 7 copy material selection button 7 copy quantity 8 correction button 8 correction button 16 e exposure level 7 exposure setting 19 ...