Summary of OCB-VT-013
Page 1
User’ s manual ocb-vt-013 gps vehicle tracker v6.3.
Page 2
- 2 - contents 1. Product overview .....................................................................................................................................................................................- 3 - 2. For your safety...............................................................
Page 3
- 3 - 1. Product overview ocb-vt-013 is a gps/gprs based tracking device specially developed and designed for vehicle real-time tracking and fleet management. Ocb-vt-013 has inbuilt gps module to obtain accurate position data and utilizes its gsm capability to send the position data to a specified m...
Page 4
- 4 - qualified service only qualified personnel can install or repair ocb-vt-013. Water resistance ocb-vt-013 is not water resistant. Keep it dry. Install it inside the vehicle or use waterproof bag if necessary. Confidential phone number for safety reason, do not tell other people the mobile phone...
Page 5
- 5 - 4.1 hardware and accessories ocb-vt-013 is supplied in a box which includes: ocb-vt-013 with battery gps antenna gsm antenna wires with sos button usb cable usb to serial cd 4.2 view front view side view back view 4.3 functional parts gps led (blue) on one button is pressed or input is active....
Page 6
- 6 - flashing ( every 0.1 second) the unit is being initialized flashing (0.1 second on and 2.9 seconds off) ocb-vt-013 is connected to the gsm network flashing (1 second on and 2 seconds off) ocb-vt-013 is not connected to the gsm network power on/off button press and hold for 3~5 seconds to turn ...
Page 7
- 7 - 4.4 connecting and installation read this manual before using your ocb-vt-013 and check if all parts are included in the packaging box. 4.4.1 ensure that your ocb-vt-013 has a working sim installed. - check that the sim has not run out of credit (test the sim in a phone to make sure it can sen...
Page 8
- 8 - example: w000000,001,123456.
Page 9
- 9 - w123456,001,999999 6. Time zone command: w******,032,t description: correct time into your local time note: 1. Default time of the tracker is gmt 2. This correction is applied to location reports by sms and sms alarms. T=0, to turn off this function. T=[-32768,32767] to set time difference in ...
Page 10
- 10 - 7.2 track by calling make a missed call to the tracker and it will report its longitude and latitude by sms with format as follows:- latitude = 22 32 36.63n longitude = 114 04 57.37e, speed = 2.6854km/h, 2008-12-24,01:50 7.3 track by preset interval command: w******,002,xxx description: set a...
Page 11
- 11 - or you can use local map software on pda or car navigation device to input the coordinates. 7.5 track by ocb-gps-server-01/ocb-gps-server-02 if you have bought our gps tracking software ocb-gps-server-01 or ocb-gps-server-02, after proper configuration, you can do tracking on ocb-gps-server-0...
Page 12
- 12 - example: w000000,011,cmnet,meiligao,6688 w000000,011,cmnet 7.6.3 set ip and port command: w******,012,ip,port description: set ip and port for tracker for gprs communication. Note: 1. Ip is your server’s ip or the domain name. 2. Port: [1,65534] example: w000000,012, 220.121.7.89,8500 w000000...
Page 13
- 13 - 7.7 track by gpsgate the ocb-vt-013 supports gpsgate software. Please contact us or gpsgate for more information of settings. 8. Authorization command: w******,003,f,p,t description: authorize phone numbers for the sos button (or inputs) for receiving location reports and sms alarms. Note: f=...
Page 14
- 14 - 9.2 detecting lock status of car’s door or trunk (car boot). Power supply lock controller lock unlock white input 1 or input 2 or input 3 lock switch when the lock is opened, there will be negative triggering to input 1 or input 2 or input 3, then an sms alarm will be sent to the authorized p...
Page 15
- 15 - application example - fuel level sensor fuel level sensors supplied by us are resistance-type sensors with output resistance: 0-200Ω(ohm). For the circuit shown on the right picture, if vcc is 12v, r should be 200Ω(ohm) and if vcc is 24v then r should be 600Ω(ohm) to make the input range to a...
Page 16
- 15 - =00, to turn off this function =01, 30m =02, 50m =03, 100m =04, 200m =05, 300m =06, 500m =07, 1000m =08, 2000m example: w000000,006,06 when tracker moves out of this square scope, it will send out an sms alarm. 12.2 geo-fence alarm command: w******,017,x or w******,117,x description: turns on...
Page 17
- 16 - p=4, output4 p=5, output5 f=0, to close the output (open drain); f=1, to open the output (low voltage). Example: w000000,020,1,1 13.2 output control (conditional) command: w******,120,abcde or w******,220,abcde description: send this command to control the output of ocb-vt-013. This command i...
Page 18
- 17 - take output1 as an example: w000000,020,1,1 (cut engine) w000000,020,1,0 (cancel engine-cut) 13.3.2 connecting with car alarm when the output that connected to the car alarm is open, the alarm will start to work. Alarm output 2 or output 3 or output 4 or output5 14. Heading change report comm...
Page 19
- 18 - description: set time interval for logging gps information. The information is stored within the device memory. When the memory gets full, the newest record will be overwritten on top of the oldest (fifo - first in, first out). In that case, only the newest information is stored. Note: 1. X=0...
Page 20
- 19 - description: this is to make all settings (except for the password) back to factory default. Note: turn on the device, press the sos button for five times continuously and the red led will be on, and then send (within 120 seconds) this sms to the tracker. ### is the ending character and is re...
Page 21
- 20 - description sms command example track on demand w******,000 w000000,000 remarks: to get the current location of the tracker, send this sms or make a telephone call directly to the tracker and it will report its longitude and latitude by sms with format as follows:- latitude = 22 32 36.63n lon...
Page 22
- 21 - x is the preset value of voltage. =0 , to turn off this function =1, =2 , =3 , =4 , =5 , speeding alarm w******,005,xx w000000,005,08 remarks: when the tracker speeds higher than the preset value, it will send an sms to the authorized phone number for sos. Xx is the preset value of speed and ...
Page 23
- 22 - b=1, location data complies with nmea 0183 gprmc protocol..
Page 24
- 23 - for example, $gprmc,161509.000,a,2232.5485,n,11404.6887,e,0.3,153.7,290709,,*03 c=0, turn off the function to automatically hang up an incoming call. C=1, turn on the function to automatically hang up an incoming call after 4 - 5 rings. D=0, turn off the function of sending an sms when the tr...
Page 25
- 24 - remarks: x=0, to turn off gprs tracking (default); x=1, to enable gprs tracking via tcp x=2, to enable gprs tracking via udp.
Page 26
- 25 - p =1, output1; =2, output2; =3, output3; =4, output4; =5,output5 set gprs interval w******,014,xxxxx w000000,014,00060 remarks: to set time interval for sending gprs packets. Xxxxx should be in five digits and in unit of 10 seconds. Xxxxx=00000, to turn off this function; xxxxx=00001~65535, t...
Page 27
- 26 - [1] in level i the gps module will be working for the first three minutes (i.E. 3 times of acquisition time) and then shut down for one minute (i.E. Equivalent to acquisition time), and then work again for another three minutes…… [2] in level ii the gps module will be working for the first tw...
Page 28
- 27 - get version no. And serial no. W******,600 w000000,600
Page 29
- 28 - remarks: to get the version and serial number of tracker’s firmware get imei w******,601 w000000,601 remarks: to get imei of the tracker reboot gsm w******,901### w000000,901### remarks: to reboot the gsm module of the tracker reboot gps w******,902### w000000,902### remarks: to reboot the gp...
Page 30
- 29 - sim is warped or damaged inspect sim, clean the contacts. If re-inserting does not help try another to see if it will work..
Page 31
- 30 - roaming not enabled if you are in a different country your sim account must have roaming enabled. Error connecting gsm antenna make sure the gsm antenna is connected to the gsm interface. Problem: sms received starts with ‘last…’ possible cause: resolution: unit does not have clear view of th...