Summary of C1241-0001
Page 1
User guide cine follow focus one c1241-0001 user guide.
Page 2
Copyright © 2011 the vitec group plc all rights reserved throughout the world. No part of this document may be stored in a retrieval system, transmitted, copied or reproduced in any way, including, but not limited to, photocopy, photograph, magnetic or other record without the prior agreement and pe...
Page 3: Contents
3 contents caution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 the cine follow focus one . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 specification . . . . . . . . . . ....
Page 4: The Cine Follow Focus One
The cine follow focus one 4.
Page 5: Specification
5 specification cine follow focus one (c1241-0001) we . . . . . . . . . . . . . . . . . . . . . . . . . Swing arm, dovetail slide driver gear coupling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Standard serrated star module coupling system . . . . . . . . . . . . . . . . . . . . ....
Page 6: In The Box
In the box 6 cff-1 studio handwheel (full-size offset knob) c1241-1100 marking discs (10 pack) c1241-1530 main bridge c1241-1400 studio rod bridge c1241-1300 swing arm c1241-1200
Page 7: Accessories
43 tooth c1241-1600 35 tooth c1241-1700 50 tooth c1241-1800 60 tooth c1241-1900 drive gears foam insert for storm case im2200 c1241-2126 part no. Drive gear lens c1241-1600 c1241-1700 c1241-1900 c1241-1800 cine cine canon eng focus fujinon eng focus driver gear 43 tooth 0.8m 6 mm face driver gear 35...
Page 8: Caution
8 Ÿ do not one handwheel. Ÿ do not hang heavy items over the handwheel. Ÿ avoid overtightening the drive gear onto the lens focus drive. Ÿ always use genuine oconnor parts and accessories with the cine follow focus one. Ÿ never use solvents or oil-based cleaners to clean the cine follow focus one. U...
Page 9: Components
Components 9 witness marker marking disc drive gear swing arm main bridge studio rod bridge cff-1 handwheel lock lever rod clamp lock lever lock lever index.
Page 10
Repositioning the lock levers 10 slide the studio rod bridge onto the main bridge. 1 2 secure the studio rod bridge using the two lock levers. Pull the lock lever towards you. A to reposition the lock levers: rotate the lock lever to the correct position. B push the lock lever to secure into positio...
Page 11
11 mounting the swing arm & drive gear 4 3 hold push fit select the correct gear for the lens in use. Ensure that the teeth on the drive gear and swing arm interlock. Secure by tightening the knurled screw on the drive gear. Note: the drive gear can be mounted on either side of the swing arm. Ensure...
Page 12: Mounting The Handwheel
Important note: ensure that you can clearly see the witness marker. Mount the handwheel in either position. 12 mounting the handwheel 5 push the handwheel firmly into the end of the main bridge. 6 push fit hold the handwheel firmly in position at the end of the main bridge and secure using the lock ...
Page 13: Mounting Onto Camera Rods
Mounting onto camera rods 13 place the cine follow focus one onto the camera rods so that the drive gear is adjacent to the lens focus drive. Secure into position using the knurled screws at the end of the studio rod bridge. 7 the cine follow focus one can be mounted from camera rods suspended above...
Page 14: Engaging The Drive Gear
Engaging the drive gear 14 8 9 note: if the swing arm is mounted on the back of the main bridge, as shown, turn the lock lever clockwise to loosen the swing arm. If the swing arm is mounted on the front of the main bridge, turn the lock lever counterclockwise to loosen the swing arm. Position the sw...
Page 15
15 10 note: the drive gear can be positioned above or below the lens depending on your camera setup. Turn the handwheel. Ensure that the drive gear engages and drives the lens focus drive..
Page 16: Marking Discs & Witness Mark
Marking discs & witness mark 16 to remove the marking disc: pull the marking disc off the handwheel. To replace the marking disc: a ensure that the cutout on the marking disc is aligned with the point on the handwheel. B slide the marking disc over the handwheel and push into position, until it clic...
Page 17: Dismounting
17 dismounting loosen the lock lever on the swing arm to disengage the drive gear from the lens focus drive. Position the drive gear away from the lens and secure using the lock lever. 1 2 loosen the knurled screws at the end of the studio rod bridge to release the rod clamps. 3 lift the cine follow...
Page 18: Storage
18 storage remove the handwheel(s) by loosening the lock lever at the back of the handwheel and sliding the handwheel free from the main bridge. 3 1 remove the drive gear from the swing arm. Loosen the lock lever securing the swing arm and fold the swing arm down onto the main bridge. 2 carefully pl...
Page 19: Oconnor Offices Worldwide
Www.Ocon.Com – sales@ocon.Com headquarters 2701 n. Ontario st. Burbank, ca 91504 usa tel.: +1 818 847 8666 fax: +1 818 847 1205 usa 709 executive blvd valley cottage, ny 10989 usa tel.: +1 845 268 0100 fax: +1 845 268 0113 brazil vitec group brazil vitec brazil tecnologias ltda. Rua quintana, 950 – ...
Page 20
C1241-4980/2 o a v connor itec group brand ™.