Octek P4X266A-A4E User Manual

Page of 20

Download

Print this page

Bookmark us

Electronic Emission Notices

Federal Communications Commission (FCC) Statement (02852C)

This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This equipment

generates, uses and can radiate radio frequency energy and, if not installed and used in

accordance with instructions contained in this manual, may cause harmful interference

to radio and television communications. However, there is no guarantee that interference

will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which

can be determined by turning the equipment off and on, the user is encouraged to try to

correct the interference by one or more of the following measures:

REORIENT OR RELOCATE THE RECEIVING ANTENNA

INCREASE THE SEPARATION BETWEEN THE EQUIPMENT AND THE RECEIVER

CONNECT THE EQUIPMENT INTO AN OUTLET ON A CIRCUIT DIFFERENT FROM

THAT OF THE RECEIVER

CONSULT THE DEALER OR AN EXPERIENCED AUDIO/TELEVISION TECHNICIAN

NOTE: Connecting this device to peripheral devices that do not comply with Class B

requirements, or using an unshielded peripheral data cable, could also result in

harmful interference to radio or television reception.

The user is cautioned that any changes or modifications not expressly approved

by the party responsible for compliance could void the user’s authority to operate

this equipment.

To ensure that the use of this product does not contribute to interference, it is

necessary to use shielded I/O cables.

copied or reproduced by any means.

While every precaution has been taken in the preparation of this manual, no responsibility

for errors or omissions is assumed. Neither is any liability assumed for damages resulting

from the use of the information contained herein.

Trademarks

All brand names, logos and registered trademarks mentioned are property of their

respective owners.

1 2 3 4 5 6 7 Next › »

Summary of P4X266A-A4E

Page 1
1 electronic emission notices federal communications commission (fcc) statement (02852c) this equipment has been tested and found to comply with the limits for a class b digital device, pursuant to part 15 of fcc rules. These limits are designed to provide reasonable protection against harmful inter...
Page 2
2 technical reference booklet table of contents hardware configuration ................................................................... 3 key features ............................................................................................................... 3 motherboard layout ................
Page 3
3 hardware configuration key features : chipset • via p4x266/p4x266a chipset. Processor • support intel® pentium® 4 processors and the northwood processors in the 478-pin package. • support intel® pentium® 4 processors system bus at 400mhz/533mhz(only for p4x266a). Vrm 9.0 (voltage regulator modules...
Page 4
4 technical reference booklet on-board creative pci sound (optional) • pnp, creative 3d enhancement. • full-duplex, sound blaster 16 compatible. • 128 voice wave table synthesizer. • dos game compatibility. • pci bus master for fast dma. • fully compliant with ac97 power management specification. • ...
Page 5
5 hardware configuration motherboard layout the following diagrams show the relative positions of the jumpers, connectors, major components and memory banks on the motherboard. Note 1) be sure to check the cable orientation in order to match the colored strip to the pin 1 end of the connector. 2) wh...
Page 6
6 technical reference booklet jumper settings this chapter explains how to configure the motherboard’s hardware. Before using your computer, make sure all jumpers and dram modules are set correctly. Refer to this chapter whenever in doubt. Cpu speed selection in this motherboard, jumperless feature ...
Page 7
7 hardware configuration sw5 - vid[0:4] code to voltage definition(optional) sw5[1:6] vcc_core sw5[1:6] vcc_core vid[0:4] vid[0:4] 1.850 1.450 1.825 1.425 1.800 1.400 1.775 1.375 1.750 1.350 1.725 1.325 1.700 1.300 1.675 1.275 1.650 1.250 1.625 1.225 1.600 1.200 1.575 1.175 1.550 1.150 1.525 1.125 1...
Page 8
8 technical reference booklet cds2 : cd-in pin assignment 1 cd-r 2 gnd 3 cd-l 4 gnd usb connector pin assignment 1 vcc 2 gnd 3 usbp1- 4 usbp0+ 5 usbp1+ 6 usbp0- 7 gnd 8 vcc j16 pin assignment 1 12v 2 gnd 3 gnd 4 vcc r g l g g l g r cds3 : cd-in pin assignment 1 gnd 2 cd-l 3 gnd 4 cd-r 1 2 7 8 lineou...
Page 9
9 vcc fp1 front panel header header 2x12 gnd 24 22 gnd 20 18 16 14 12 irtx 10 gnd 8 irrx 6 gnd 4 sus+ 2 sw - pwr+ - sw +sus led - pwr+ led - hdd+ sw - rst+ + - nc s spker irda + tx - rx 23 21 gnd 19 17 speak 15 gnd 13 rst+ 11 hddled- 9 hddled+ 7 pwrled- 5 pwrled+ 3 gnd 1 pwr+ x x x vcc x vcc.
Page 10: Checking The Mounting Post
10 technical reference booklet checking the mounting post of your computer please check your computer chassis if it is carrying any metal mounting post at this location. Remove the mounting post or add insulation to the post before putting in the motherboard. Caution clip clip dimm dimm socket notch...
Page 11
11 hardware setup installing a new processor an upgrade processor can dramatically increase general system speed and performance. Most microprocessor upgrade kits include the following items: • microprocessor chip • installation instructions and technical data before installing the processor, please...
Page 12
12 technical reference booklet bios setup this chapter discusses award’s setup program built into the rom bios. The setup program allows users to modify the basic system configuration. This special information is then stored in battery-backed ram, which retains the setup information when the power i...
Page 13
13 bios setup main menu once you enter the award bios cmos setup utility, the main menu will appear on the screen. The main menu allows you to select from various setup functions and two exit choices. Use the arrow keys to select among the items and press to accept and enter the sub-menu. Cmos setup...
Page 14
14 technical reference booklet load optimized the chipset defaults are settings which provide for maximum defaults system performance. While award has designed the custom bios to maximize performance, the manufacturer has the right to change these defaults to meet its needs. Set supervisor/ changes,...
Page 15
15 bios setup ide primary these categories identify the types of the two channels that master/slave have been installed in the computer. Ide secondary master/slave if the controller of the hdd interface is scsi, the selection shall be “none”. Drive a / this category identifies the types of floppy di...
Page 16
16 technical reference booklet pnp/pci configurations this section describes how to configure the pci bus system. This section covers some very technical items and it is recommended that only experienced users should make any changes to the default settings. Pc health status the pc health status dis...
Page 17
17 flash update procedure a program awdflash.Exe is included in the utility diskette or cd (x:\utility\ awdflash.Exe). The user is recommended to follow the procedure below to update the flash bios. (x: your cd driver letter). 1. Create a dos-bootable floppy diskette. Copy the new bios file (just ob...
Page 18
18 technical reference booklet appendix appendix ac97 sound driver installation for windows nt 4.0/2000/xp please follow the step to install ac97 sound driver for windows nt 4.0/2000/xp. (note : this manual assumes that your cd-rom device drive letter is d:.) d:\via chipset\ac97_8233\.
Page 19
19.
Page 20
20 technical reference booklet 02852c.