1. DL manuals
  2. ODES UTVS
  3. Utility Vehicle
  4. DOMINATOR X- 2
  5. Assembly Instructions Manual

ODES UTVS DOMINATOR X- 2 Assembly Instructions Manual

Manual is about: 2 door

Summary of DOMINATOR X- 2

  • Page 1

    Dominator x - 2 assembly instructions model year: 2015 model engine size category 2 door 800cc/1000cc off-road important information the assembly instructions in this guide are for 2015 dominator x - 2 door models only. Please make sure a pdi was performed on each unit before the assembly begins. Al...

  • Page 2: Uncrating/removing Parts

    Uncrating/removing parts from crate when you’re ready to start assembling your utv make sure you set up your crate on a flat and level surface. Once you have done that, you can begin to uncrate the utv. *for safety purposes we reccomend having a partner when uncrating the utv as the crate guards can...

  • Page 3: Roll Cage Assembly  1-1

    Roll cage assembly 1-1 once you begin assembling the rollcage, we encourage you to lay the frame flat on the ground so the bars can be inserted easily. Once you align the front bar as shown in the image to the left, you can begin to bolt them down. Please place a washer on both sides of the bolt. On...

  • Page 4: Roll Cage Assembly 1-2

    Roll cage assembly 1-2 once you have the front and x bar bolted down, you can now place the other side of the rollcage on its support bars. *for your safety, we reccomend having a partner help carry the second half of the rollcage. You can now begin to align the frame with the bolt holes in the supp...

  • Page 5: Roll Cage Assembly 1-3

    Roll cage assembly 1-3 once you have the rollcage bolted down and secure, you can now attach it to the frame of the utv. *for your safety, we reccomend having a partner help carry the assembled rollcage over to the utv frame. Align the rollcage with the holes provided on the frame. Please refer to t...

  • Page 6: Seat Belt Assembly

    Seat belt assembly once your rollcage is bolted to the frame, you can begin to unwrap the seat belts and attach them to the seat belt bracket. Fully extend the seatbelt so it reaches the bracket and bolt down the seat belt to the bracket. Please make sure these are se- cured and installed correctly....

  • Page 7: Cross Brace Installation

    Cross brace installation once the seat belts are properly installed you can now begin to attach the cross braces to the back of the roll cage. Align the cross braces with the brackets provided on the roll cage, refer to the im- age for exact location. Be sure to properly align and bolt down the cros...

  • Page 8: Shock Installation 1-1

    Shock installation 1-1 the front shocks on the x model come preinstalled with the bottom already bolt- ed down. You need to simply bolt down the top of the front shock for both driver and passenger sides. Before going on to the rear shocks, we advise you to attach the rear brake line first as the sh...

  • Page 9: Shock Installation 1-2

    Shock installation 1-2 when installing the rear shocks you will need someone to lift the arm while anoth- er person aligns the top of the shock with the bolt hole. Once you have the shock aligned with its holes you need to bolt down the shocks and make sure they are fully secure. You will need to do...

  • Page 10: Tire Installation

    Tire installation before installing the tires, please make sure to inflat both the front and rear to 15 psi. Securely bolt down all 4 tires to the utv. Once all tires are bolted down you can now lower the utv back to the ground using the forklift and finish off the tires by tightening them with a to...

  • Page 11: Rear Mudguard

    Rear mudguard align the plastic rear mudguard with the holes provided on the frame. Screw in the mudguard screws with their aligned holes. There are four holes that need to be screwed down, please make sure all 4 of these are fastened tightly..

  • Page 12: Side Fearing

    Side fearing align the side fearing with the holes pro- vided on the frame. The side fearing will attach to the utv by 3 bottom bolts on the very bottom under- neath the fearing. And 2 push pins that go on the top back- side of the fearing. Refer to the image for exact location..

  • Page 13: Muffler Installation 1-1

    Muffler installation 1-1 cut the zip ties that are currently holding up the exhaust pipe /dump bed motor and remove all bubble wrap. Install the muffler by pushing it into the exhaust pipe and align it with the provided hose clamp. Once the clamp, muffler and pipe are all in place, tighten the clamp...

  • Page 14: Muffler Installation 1-2

    Muffler installation 1-2 begin bolting down the muffler to the frame of the utv, there will be 3 bolts that need to be inserted and tightened. Please make sure you tighten all bolts to ensure a secure and fitted exhaust pipe. The last step in installing the muffler is to install the heatshield. The ...

  • Page 15: Dump Bed Installation

    Dump bed installation with a partner, pick the dump bed up and place it on the frame. Both you and your partner should both check for any alignment issues that may cause issues installing the fender flares. If you run into any alignment issues we do have an alignment manual available for download on...

  • Page 16: Battery Box

    Battery box once you are done installing the dump bed you will need to connect the battery box. Take off the pins on the battery box. Be sure to attach all battery terminals in the box, this is important - the battery needs to be operational in order for you to test the dump bed motor and led light ...

  • Page 17: Dump Bed Motor

    Dump bed motor once you have the battery connected, fully extend the dump bed motor by press- ing the up arrow on the dash. Don’t forget to attach the rubber stoppers on the bottom of the bed (there are two). Connect the dumpbed motor to the bot- tom of the bed, make sure you securely clip down the ...

  • Page 18: Dust Cover Installation

    Dust cover installation unbolt the seatbelts in order to install the dust cover . Once you have the seatbelts detached on both driver and passenger sides you can begin to install the dust cover. Align the two slits as shown in the image to the left. Once you have the dust cover secure and the seatbe...

  • Page 19: Air Intake Installation

    Air intake installation once the dump bed and dust cover are installed you can now install the air intake system. Make sure you untuck the hose if it happened to get tucked underneath the intake. Push the hose through the hole on the intake system and make sure it is secure. Clamp the intake system ...

  • Page 20: Rear Fender Flares

    Rear fender flares the rear fender flares have several holes that need to be secured by push pins, make sure you do not skip over any holes and make sure you have the fender flare properly aligned with the holes before ap- plying the push pins. You wull need to place push pins on both the outside of...

  • Page 21: Hood Installation

    Hood installation the hood is held together by two hinges and a metal plate underneath the hinges. When installing the hood, you will need to unscrew the metal plate before screwing in and securing the hinges. Be sure you properly secure both hinges down and your hood lifts up and goes down properly...

  • Page 22: Hood Support Bracket

    Hood support bracket align the hood support bracket with the holes on the frame. Insert 4 bolts to secure the hood support bracket down. Tighten all 4 bolts and make sure the hood support bracket is straight to avoid an offset hood..

  • Page 23: Front Bumper

    Front bumper align the front bumper with the bumper bracket on the frame. Secure the bumper down with 4 bolts. You will then need to drill the bolts down. The end result should look like the image to the left. The front bumper should align perfectly with the frame..

  • Page 24: Radiator/ Side Guards

    Radiator/ side guards align the radiator guard with the holes on the frame as shown in the image to the left. Before bolting down the radiator guard you will need to first add the two mud- shields to the left and right side. Once you have the radiator guard and mudshields in place, you will then nee...

  • Page 25: Front Winch 1-1

    Front winch 1-1 align the winch bracket with the holes on the front bumper. Place the winch on top of the winch brack- et and begin to bolt it down from the bot- tom of the bracket, do not tighten yet. Pull the winch cable out a bit, push the cable through the front of the guard and begin bolting do...

  • Page 26: Front Winch 1-2

    Front winch 1-2 install the winch hook by pushing the bolt through and securing it with a bolt clip. You can now drill down all bolts to secure the winch to the bumper/frame. You can now attach the winch wires, red goes on the bottom connectors and black goes on the top connectors. Be sure to test y...

  • Page 27: Front Bumper Leds

    Front bumper leds to install the front bumper leds you first need to attach the brackets using two bolts on each side. Make sure you tighten all 4 bolts before attempting to place the leds on the bumper. Align the leds with the holes provided on the front bumper and tighten them down using 2 bolts. ...

  • Page 28: Front Bumper Guard

    Front bumper guard align the front bumper guard with the bumper, make sure your bumper guard is on straight before attempting to drill any- thing down. Once you have the bumper guard properly aligned with the front bumper, you can begin drilling in the screws. There will be 4 screws that need to be ...

  • Page 29: Front Fender Flares

    Front fender flares be sure all holes on the hood are punched out properly before placing the fender on the hood. Align the holes on the hood with the fend- er flare and begin to secure the flare down with push pins. There are several holes that need to be se- cured with push pins, please ensure eac...

  • Page 30: Roof Installation

    Roof installation to properly install the roof you will need to make sure both sides of the roof prop- erly align with the roll cage. The backside of the roof should look like this when aligned properly, there should be no gaps inbetween the rollcage and the roof. To securely install the roof to the...

  • Page 31: Rear Bumper

    Rear bumper align the rear bumper with the bumper brackets on the bottom of the dump bed. Once aligned, you can drill the bolts through the bracket, make sure it is tight and secure to avoid bumper movement while riding. There are 2 bolts that need to be tightened when installing the rear bumper, pl...

  • Page 32: Rear Winch

    Rear winch the rear winch is fully assembled, you need to simply align it with the hitch bracket underneath the dump bed. Once aligned, you can then place the pin through the bracket and clip it down to fully secure it. Once the rear winch is fully secured on the bracket, you can then connect the wi...

  • Page 33: Rearview Mirrors

    Rearview mirrors to install the rearview mirrors you will need to bolt them down to the rollcage. Align the mirror to the frame properly by making sure the mirror is straight before drilling it down. Drill the mirror to the frame, be sure to do this for both passenger and driver side. The end result...

  • Page 34: Door Bracket

    Door bracket to install the doors you will first need to attach the door bracket to the front fender flare. To do so, you will need to drill in 4 bolts and apply 2 push pins. For a better sense of location, please view our domi- antor x assembly video which is available in the “my dealer services” s...

  • Page 35: Doors

    Doors once the door bracket is installed and you have pushed the door hinges through, you can now tighten the door hinges to the frame. There are 4 bolts that will need to be tight- ened, please be sure you tighten all 4 bolts to reduce any play in the door while riding. Once all door hinges are bol...

  • Page 36: Led Lightbar 1-1

    Led lightbar 1-1 to install the lightbar you are going to want to install the side brackets as well as the bottom bracket first. There will be a total of 4 screws to be bolted in, 2 on top and 2 on the sides of the lighbar bracket. The ending result should look like the im- age to the left as well a...

  • Page 37: Led Lightbar 1-2

    Led lightbar 1-2 align the led lightbar on the bracket and make sure the lightbar is straight. Once it is straight you can then bolt the lightbar to the bracket. Once the lightbar is secure, you can then push the wire through the hole on the roof. Once you push it through the hole on the roof you ca...

  • Page 38: Front Roof Mount

    Front roof mount slide the front roof mount underneath the roof, there are brackets in place that should align with the mount. Once the mount is in pleace you will need to screw in the two bracket bolts to hold the lightbar and bracket in place. Once you have the lightbar fully secure, you can now i...

  • Page 39: Front Windshield

    Front windshield align the windshield within the grooves on the hood of the utv. Make sure the windshield is straight with no offset. Place the side clamps on the provided holes and run the bolt through it. You will need to install 4 clamps and run 4 bolts through those clamps. 2 on the driver side ...

  • Page 40: Seat Installation

    Seat installation the new seats have an easy install sys- tem, you’ll need to simply align the 3 ridges in the image to the left with 3 holes provided on the frame of the utv. To snap the chair in place you will need to push down on the front of the seat once you slide it in and ensure the marked ar...

  • Page 41: Steering Wheel

    Steering wheel the last thing to do to complete the domi- nator x assembly is to attach the steering wheel. Make sure the seatbelt is straight as well as the wheels before bolting down. Place the steering wheel cap on the steer- ing wheel and begin placing the bolts. Once all bolts are in place and ...