Summary of AB-1000MG
Page 2: Warning
Warning before turning the power on, please make sure that there are no objects obstructing the operation of the rollers and wheels. When operating the models ab- 1000mg, ab-1000 uv and ab-1000mg/uv, please wait 5 minutes to allow the uv and/or magnetic systems to reach its maximum detection capabil...
Page 3
Part one: basic instructions for all models basic instructions 1.0 general controls 1.1 specific controls 2.0 features 2.1 counting mode 2.2 preset batching function 2.3 add mode 2.4 detect mode 2.5 automatic start 2.6 repeat function “batch” 3.0 operations 3.1 power up 3.2 mode selection 3.3 “count...
Page 4
Part two: instructions for cleaning of the machine and troubleshooting operational problems 4.0 cleaning of the machine 4.1 cleaning of optical sensors 4.2 cleaning the inside of the machine 4.3 additional recommendations 5.0 trouble shooting operational problems 5.1 avoiding problems 5.2 jamming 5....
Page 5
General conveniently compact and stylish, the machines in the ab-1000 series have been specifically designed to accurately count bank notes in bulk, thus reducing labor time and losses due to human error. Moreover, the machines in the ab-1000 series are equipped with a micro-computerized mechanism t...
Page 6
Model ab-1000 uv: in addition to the functions of the ab-1000, this machine has an integrated counterfeit banknote detection device that works by means of uv fluorescent detection. Like model ab-1000 mg, the machine will beep when a suspect bill is detected. Model ab-1000 mg/uv: in addition to the f...
Page 7
1-800-543-5454 www.Officezone.Com officezone.
Page 8
1-800-543-5454 www.Officezone.Com officezone.
Page 9
Preset number display (batch display) counting number display (counter) batch + button (to add) batch - button (to subtract) batch button (preset 10, 20, 25, 50, 100, ø) clear button for main display restart button (for manual restart) add button (adding function) mg button (magnetic detection) 1-80...
Page 10
Preset number display (batch display) counting number display (counter) batch + button (to add) batch - button (to subtract) batch button (preset 10, 20, 25, 50, 100, ø) clear button for main display restart button (for manual restart) add button (adding function) mg button (magnetic detection) uv b...
Page 11
2.1 counting mode once turned on, the machine defaults to this mode, counting all the bill placed in the hopper. 2.2 preset batching function counts bills per batch up to the numbers preset with the “batch” and “+” or “-” buttons. 2.3 add function counts all bills placed in the hopper and will add t...
Page 12
3.1 power up connect the power cord to the power source and turn the power switch on; the unit will conduct a self-check by spinning the counting wheels several times. The counting number display will show “0” when the unit is ready. 3.2 mode selection select the function you want to use: “add” or “...
Page 13
Loading the hopper with additional bills, without removing previous notes accumulated on the stacker, will start the next counting operation automatically. The newly counted number will be added to the previous one. Additionally, the machine has two modes for counting in case it detects a counterfei...
Page 14
Uv function: the uv function is able to check all types of banknotes. Put the ultraviolet sensitivity switch at the lowest level before turning the power on. The ultraviolet function will work at its best after five minutes. If the detection function is not working properly; adjust the switch to a h...
Page 15
3.6 “add” function addition can be performed by pressing the “add” button until its indicator is lit up. In this case, removing the counted bills from the stacker will not clear the counted number on the display screen, and the counted number of the next bills will be added to the preceding one. To ...
Page 16
If the counted number does not tally with the preset number, the batch counter will show the quantity counted, which will be displayed on the screen with a blinking number. Keeping the “ + ” button pressed for more than 0.5 sec. Will cause the set number to increase one by one, every 0.25 sec. When ...
Page 17
4.1 cleaning the optical sensors it is very important to clean all the sensors in the machine with a soft brush to avoid any paper particles or dust from sticking to the light-transmitter or the light-receiver sensors. This should be done every day. If necessary, the glass surfaces of the detectors ...
Page 18
5.1 avoiding problems pre-select the bills you are going to count in the machine. Do not drop into the machine: bills with metal clips broken bills bills with plastic transparent tape washed bills 5.2 jamming before you start operating the machine make sure there are no foreign elements in any of th...
Page 19
Check adjustment screw (# 22) on the back. The counter-clockwise direction will reduce friction. Make sure that you are positioning the bills correctly in the hopper. Try again. 5.3 when counting numbers are wrong turn the up and down adjustment screw (#22) clockwise to increase the friction. Adjust...
Page 20
E-1 e-2 e-3 e-4 e-5 the left counting sensor is dirty or damaged the right counting sensor is dirty or damaged the fluorescent sensor or the ultraviolet lamp is damaged the auxiliary hopper plate or the friction rollers system is dirty the preset sensor is full of dust or damaged clean or change the...
Page 21
0 0 ambient temperature: 0 c - 40 c ambient humidity: 25% - 80% feed system: roller friction system hopper capacity: 100 old bills or 200 new bills stacker capacity: 100 old bills or 200 new bills size of countable bills: 50mm x 100mm - 100mm x 185mm thickness of countable bills: 0.06mm - 0.12mm cou...