1. DL manuals
  2. Ofna Racing
  3. Motorized Toy Car
  4. PICCO OFF ROAD
  5. Instruction Man

Ofna Racing PICCO OFF ROAD Instruction Man

Manual is about: HI PerFORMANCE 1/8 OFF-ROAD NITRO BUGGY

Summary of PICCO OFF ROAD

  • Page 1

    Instruction manual ofna 7 vanderbilt, irvine, ca 92618 ph. (949) 586-2910 hi performance 1/8 off-road nitro buggy..

  • Page 2

    Aa batteries ( 12 pcs ) tools not included in kit, but needed to maintain your car. Phillips type screw drivers ( l ) phillips type screw drivers ( s ) needle nose pliers cutter curved scissors #91009 $5.95 instant cement cross wrench #17109 $3.95 grease you need to get batteries for the radio trans...

  • Page 3: Failure to Not Read And

    Running a nitro kit is fun and easy, but to make this a safe • clean oil and dirt from chassis with a degreaser like simple green. And good experience you must observe a few rules. This kit is extremely fast, easily over 40mph, and can seriously precautions injure someone if you are not careful. • t...

  • Page 4

    Option things need besides the kit radio control unit 12v battery for starter box (must have) glow plug heat with battery & charger # 10227....$$19.95 (please note ofna glow heats available) aa batteries ( 12 pcs ) for radio note: carefully read the instruction manual of your 2 channel radio control...

  • Page 5

    Plastic parts for use 40047 receiver box 36901 front knucklearm arm 36081 upright rear 40003 diff. Case 40020 rear lower arm 40202 lower arm front 40017 gear box 40046 stone guard.

  • Page 6

    40040 center diff. Mount symbol used throughout the instruction manual ensure free movement ensure free movement apply grease apply grease oil tighten tighten do not over tighten rotate direction rotate direction contact adhesive contact adhesive s re c w ceme t n bag 1:1 parts bag used degrease wit...

  • Page 7

    1 2 3 assembly of the front and rear diff. Assembly of the front and rear diff. Assembly of the center diff. Step 1 step 2 step 1 step 2 step 1 step 2 4x4 mm 40009 36053 oil builds two differentials for front and rear. .....X8 30776 4x10mm washer 30773 4mm cross pin .....X4 . O l diff i 40011 3x12mm...

  • Page 8

    4 5 assembly of the center diff. Assembly of the front gear case step 1 step 2 step 1 step 2 .....X4 30776 4x10mm washer 30773 4mm cross pin .....X2 diff. Oil 40011 3x12mm ....4 tight the diff screws in this order. 1 4 3 2 c w s re ce n me t 36053 8x16mm ball bearing .....X2 use 5000 weight diff. Oi...

  • Page 9

    7 8 9 assembly of the front lower arms assembly of the front upper arms assembly of the knuckle arms assembly for both right and left side. 3 step 1 step 2 36053 do not over thigten scre w cem ent ensure free movement .....X4 2.5mm 36170 2.5mm 34053 l 36901 36904 36905 36903 36904 36905 36903 30656 ...

  • Page 10

    10 11 12 assembly of the front suspension arms assembly for both right and left side. Assembly of the front stabilizer assembly for both right and left side. Assembly of the front stabilizer 4 3x16mm 3x10mm 3x3mm 40018 3x3mm ensure free movement screw cement scr ew m n ce e t 3x3mm 3x3mm makes two r...

  • Page 11

    13 14 15 assembly of the servo saver assembly of the servo saver and the steering tie-rod 5 step 1 step 2 step 1 step 2 assembly of the servo saver onto the front gear box ½ w ½ Ä ² Õ » p « e ¾ ¦ ½ ü ½ c ² Õ ¦ x 40031 40037 40031 49052 40018 40036 3x10mm 36790 40038 4x10mm 3x10mm 4x10mm 40031 plasti...

  • Page 12

    40027 3x10mm 41010 41010 16 assembly of the rear gear case step 1 step 2 step 1 step 2 3x20mm 40027 40027 3x16mm 94005 3x16mm hex screw .....X2 94007 3x20mm hex screw .....X4 40027 40027 40027 3x16mm 3x20mm 40027 49050 41009 94003 3x10mm hex screw .....X1 94010 4x12mm hex screw .....X4 36053 8x16mm ...

  • Page 13

    19 20 21 assembly of the wing stay assembly of the rear lower arms assembly of the rear suspension arms 7 step 1 step 2 assembly for both right and left side. 3mm 40524 94011 4x16mm hex screw .....X2 94012 4x20mm hex screw .....X4 5x4mm .....X2 ensure free movement 90021 3mm e-ring .....X2 .....X4 3...

  • Page 14

    22 23 24 8 assembly of the rear suspension arms assembly for both right and left side. Assembly of the rear stabilizer assembly of the rear stabilizer 36850 36861 40065 3x25mm 3x18mm 40019 3x3mm 3x10mm 40018 94006 3x18mm hex screw .....X2 3mm nylon nut 3mm nylon nut 94041 3mm nylon nut .....X4 ........

  • Page 15

    25 assembly of the center diff. Mount 9 27 assembly of the center diff. Mount step 1 30213 3x3mm *approx. 8mm *8 m m ¬ù step 2 30171 3x12mm approx. 4mm step 1 94033 3x3mm set screw .....X2 94004 3x12mm hex screw .....X4 30171 3x3mm 40040 40040 3x12mm 40042 40042 26 assembly of the brake disk into ce...

  • Page 16

    40046 29 30 10 28 assembly of the front gear case onto chassis 4x16mm 94026 4x12mm flat head hex screw .....X2 4x12mm 94027 4x16mm flat head hex screw .....X4 4x10mm assembly of the center diff. Onto chassis 40028 4x10mm 4x10mm *insert the drive shaft into the cap joint before assembly the center di...

  • Page 17

    11 32 assembly of the radio tray and receiver box step 1 step 2 40047 10282 40047 40047 30560 3x10mm * use the screw provided with your switch . 2x10mm 2x25mm receiver switch 2x10mm tapping screw .....X2 2x25mm screw .....X1 3x12mm 33 94003 3x10mm hex screw .....X1 94004 3x12mm hex screw .....X2 31 ...

  • Page 18

    35 36 12 34 assembly of the radio tray and stick pack battery 40130 94003 3x10mm hex screw .....X2 step 1 step 2 40130 3x10mm 3x10mm 40130 assembly of the radio tray onto chassis 3x10mm 94019 3x10mm flat head hex screw .....X8 3x10mm 94004 3x12mm hex screw .....X1 3x12mm 3mm 3mm nut .....X1 34 assem...

  • Page 19

    38 13 39 37 assembly of the clutch and engine mount step 1 step 2 10399 34110 3x5mm 5x9x0.3mm 3x8mm 3x16mm 3x16mm .....X2 .....X1 .....X1 5x9x0.3mm washer 34110 5x10x4mm ball bearing 3x8mm washer 3x5mm cap screw 3x16mm cap screw .....X1 .....X4 3mm nylon nut .....X4 34110 3mm 3mm assembly of the clu...

  • Page 20

    Cut off the servo saver as shown. Assembly of the throttle linkage 2mm nut .....X2 2x7mm 2x4mm 3x3mm 2x7mm 2x4mm 2x25mm 30802 36140 30172 42 step 1 ensure free movement 3x10mm 94003 3x10mm hex screw .....X1 2x8mm screw hex .....X2 94033 3x3mm set screw .....X3 2x4mm screw hex .....X2 2x7mm washer .....

  • Page 21

    45 assembly of the air filter 43 44 zip ties 40129 40127 40128 40127 3x8mm *apply filter oil to the foam before use. *apply filter oil to the foam before use. 94002 3x8mm hex screw .....X1 adjusting the engine control linkages approx. 1mm gap (neutral) (throttle high) (brake) idling adjusting screw ...

  • Page 22

    46 47 assembly of the front shocks assembly of the rear shocks step 1 step 2 step 3 step 4 fit the o-ring into groove before assembly fill the shocks with oil. 2 8 m m correct shock assembly carefully screw the shock shaft into the bottom of the plastic ball and until the distance between the ballen...

  • Page 23

    48 49 assembly of the front shock absorber assembly of the rear shock absorber 17 assembly for both right and left side. Assembly for both right and left side. 3x20mm 94007 3x20mm hex screw .....X2 .....X2 94040 3x8mm washer 94041 3mm nylon nut .....X2 3x20mm 3mm 3x8mm 3mm 94007 3x20mm hex screw ......

  • Page 24

    51 52 assembly of the wing assembly of the tires and wheels 18 step 1 step 2 in s ta n t g l u e apply instant glue into the groove of the wheel. 86082 86056 81095 .....X2 .....X2 94004 3x12mm hex screw 94041 3mm nylon nut 3x12mm 40027 3mm 3mm 53 assembly of the tire onto front knuckle and rear hub ...

  • Page 25

    19 54 assembly of the body and painting cut out the body as shown. Use a neutral detergent to remove any dirt and oil. Mask the windows from the inside with masking tape. Apply internal color decals from the inside and paint the body with polycarbonate spray paints. Spray paint cutting holes. *hole ...

  • Page 26

    55 mounting body 20 1.2v 56 starting of the engine 1. Turn on transmitter and then receiver. 2. Fill fuel tank with fuel bottle. 3. Connect 1.2v glow plug starter. 4. Start engine with 12v starter. ( note the direction of the starter.) 5. After the engine be started, remove the 1.2v glow plug starte...

  • Page 27

    Ofna description retail ofna description retail 10010 clucth shoes black 3pcs 13.95 40028 dog bones, 93mm pair lx1 19.95 10040 3 pin flywheel, .21 corn type 14.95 40029 ball ends, plastic, anti-roll 3.95 10060 manifold, round exht, black 25.95 40031 servo saver horn 15.95 10069 seals .21, red round ...

  • Page 30: Setting Guide

    Setting guide front camber angle setting rear camber angle setting place the model car on flat surface. Raise the chassis to it's maximum clearance before the wheels leave the ground. Adjust the length of the front and rear upper arms so that the wheels are right angle to the ground. The camber angl...

  • Page 31

    Racer’s name tel:( ) address city state zip dealer’s name tel: ( ) address city state zip ofna racing congratulates you on your purchase of our fine ofna product. With proper maintenance and han- dling this kit will provide many hours of enjoyment. The registration card should be filled out and mail...