1. DL manuals
  2. Ofna Racing
  3. Motorized Toy Car
  4. ULTRA GTP II 34316
  5. Instruction Manual

Ofna Racing ULTRA GTP II 34316 Instruction Manual

Summary of ULTRA GTP II 34316

  • Page 1

    This is not a toy ! Additional parts needed instruction manual #34316 #34317 * batteries 8 aa for radio * receiver batteries (10202 hump pack) * model fuel 20% nitro * ca glue this kit is extremely fast, and can easily go over 40mph and can seriously injured someone. If you are under 18years of age ...

  • Page 2: Rod!

    Must read this before running running a nitro kit is fun and easy, but to make this a safe • clean oil and dirt from chassis with a degreaser. And good experience you must observe a few rules. This precautions kit is extremely fast, easily over 40mph, and can seriously • this kit is not a toy. Alway...

  • Page 3

    Things need besides the kit radio control unit 12v battery for starter box (must have) glow plug long heat with battery & charger # 10215....$27.95 (please note ofna glow heats available) aa batteries ( 12 pcs ) for radio note: carefully read the instruction manual of your 2 channel radio controller...

  • Page 4

    30121 4x3x3mm chromed tube 1 2 3 assembly of the front and rear diff. Assembly of the front and rear diff. Assembly of the front and rear bevel gears step 1 step 2 step 1 step 2 step 1 step 2 30620 7x19x6mm ball bearing 94034 4x4mm set screw 30779 2x12.8mm pin .....X4 .....X4 .....X4 .....X2 30777 p...

  • Page 5

    4 assembly of the gear box and front shock stay step 1 step 2 apply grease sc rew ce me nt 94011 4x16mm hex screw .....X2 2 30630 30010 30082 30130 30630 5x5mm 30630 6x13x5mm ball bearing .....X2 94029 4x25mm flat head screw .....X2 94036 5x4mm set screw .....X1 94009 4x10mm hex screw .....X2 94023 ...

  • Page 6

    7 8 9 assembly of the front knuckle arms assembly of the front knuckle and front suspension arms assembly of the front stabilizer 3 step 2 step 1 94036 5x5mm set screw .....X2 36903 36904 36905 36901 5x4mm 36052 30656 36053 36053 36055 ensure free movement do not over tighten 36053 8x16x5mm ball bea...

  • Page 7

    10 11 12 assembly of the front stabilizer assembly of the servo saver assembly of the servo saver and the steering tie-rod 4 3x8mm 94040 3x8x0.8mm 3x3mm 3x3mm 94033 3x3mm set screw .....X2 94002 3x8mm hex screw .....X2 re sc w m ce ent scr ew ce n me t ensure free movement .....X4 .....X2 step 1 ste...

  • Page 8

    13 14 15 assembly of the servo saver onto the front gear box assembly of the gear box and rear shock stay 5 assembly of the rear lower arms 94003 3x10mm hex screw .....X2 3x15mm 3x15mm 3x10mm 40039 40039 3mm 3mm 94021 3x15mm flat head screw .....X2 .....X2 94041 m3 nylon nut step 1 step 2 30630 6x13...

  • Page 9

    16 17 18 assembly of the rear suspension arms assembly of the rear suspension arms assembly of the rear stabilizer 6 assembly for both right and left side. 3x4mm 34055 36082 36081 34035 36053 8x16x5mm ball bearing .....X4 94001 3x4mm hex screw .....X2 36055 2.5x16.8mm pin .....X2 36053 36053 36055 3...

  • Page 10

    19 20 21 assembly of the rear stabilizer assembly of the rear body post assembly of the two speed gears 7 94033 3x3mm set screw .....X2 94022 3x8mm hex screw .....X2 m2 nut .....X2 94041 m3 nylon nut .....X2 35230 8x12x3.5mm flange ball bearing .....X2 35237 4x6mm set screw .....X1 3x8mm 3x8x0.8mm 3...

  • Page 11

    22 23 24 8 assembly of the two speed transmission into the center mount assembly of the brake disk into center diff. Mount .....X2 94036 5x5mm set screw 94005 3x15mm hex screw .....X2 94033 3x3mm set screw .....X1 step 2 step 1 30620 7x19x6mm ball bearing .....X2 40218 8x12x1mm 30620 30170 30170 306...

  • Page 12

    25 27 assembly of the center diff. Onto chassis 9 26 94027 4x16mm flat head hex screw .....X4 34050 4x16mm 4x16mm *insert the drive shaft into the cap joint before assembly center diff. Onto chassis. Assembly of the front gear case onto chassis 94019 3x10mm flat head hex screw .....X2 94026 4x12mm f...

  • Page 13

    28 29 30 assembly of the front servo and radio tray 10 94003 3x10mm hex screw .....X4 step 2 step 1 3x16mm 3x8x0.8mm 34026 steering servo 34026 34026 3x10mm 30648 34015 34012 94005 3x16mm hex screw .....X4 3x10mm assembly of the stone guard onto chassis 94019 3x10mm flat head hex screw .....X6 3x10m...

  • Page 14

    31 32 33 assembly of the radio tray onto chassis 11 94018 3x10mm flat head hex screw .....X5 3x10mm 3x10mm 94003 3x10mm hex screw .....X2 assembly of the radio tray and receiver box step 1 step 2 3x10mm 30560 3x10mm 34013 10282 30647 3x10mm 94003 3x10mm hex screw .....X6 2x8mm screw .....X2 battery ...

  • Page 15

    34 35 36 assembly of the clutch 12 step 1 step 2 10098 10010 10102 *fit the flywheel using a pair of the plier and cross wrench. Re sc w e t c m en 10040 10330 engine rotation direction. Tighten *place the clutch shoes with the clutch springs over the 3 pins of the flywheel. *using a phillips screw ...

  • Page 16

    38 39 assembly of the clutch onto engine mount and muffler assembly of the engine onto chassis 13 37 step 1 step 2 94041 3mm nylon nut .....X4 10185 31990 30480 3mm 3x16mm .....X4 30481 3x16mm cap screw *slide the 3mm nylon nut into engine mount. Assembly of the clutch step 3 step 1 step 2 5x9x0.3mm...

  • Page 17

    41 42 assembly of the throttle linkages into lever 14 40 assembly of the muffler onto chassis 10120 10069 assembly of the throttle linkage step 1 step 2 step 3 94033 3x3mm set screw .....X3 2mm nut .....X2 2x8mm screw 2x25mm screw .....X2 .....X1 2x4mm screw .....X1 94036 5x5mm set screw .....X1 940...

  • Page 18

    44 45 assembly of the rear shocks 15 43 .....X2 .....X4 .....X2 .....X4 .....X2 .....X2 adjusting the engine control linkages approx. 1mm gap (neutral) (throttle high) (brake) idling adjusting screw . 10300 0 ¬ù .5 m m approx. 0.5mm carburetor is opening fully 40090 2mm washer 40090 1mm washer 40090...

  • Page 19

    47 48 16 46 assembly of the front shock absorber assembly of the rear shock absorber 94041 3mm nylon nut .....X2 94007 3x20mm hex screw .....X2 3mm 3x25mm 40531 94040 3x8mm 3x20mm 3mm 40531 3x8mm 3x20mm 3x25mm 90018 3x25mm cap screw .....X2 94041 3mm nylon nut .....X2 94007 3x20mm hex screw .....X2 ...

  • Page 20

    50 51 assembly of the fuel tube 17 49 assembly of the air filter assembly of the front bumper step 2 step 1 31159 34091 33011 33011 34090 4x12mm 4x16mm step 1 step 2 40128 40127 3x8mm 94002 3x8mm hex screw .....X1 33011 connect to carbulater. Connect to fuel nipple. Connect to fuel tank nipple. Conn...

  • Page 21

    18 52 assembly of the tires and wheels 86026 86059 inner sponge (wide) 86050 86059 inner sponge (narrow) in t n s a t g lu e contact adhesive contact adhesive *pull back the tire bead slightly and spot glue in four spots as shown. When dry, glue the rest of the wheel between the spots. Repeat the pr...

  • Page 22

    19 55 assembly of the rear wing take off the doubleside paper before assembly. Side plate side plate doubleside tape doubleside tape nylon screw * take the side plate as picture shown. Nylon nut do not over tighten 56 mounting body 31159 31159 31159 31159.

  • Page 23

    1. Turn on transmitter and then receiver. 2. Fill fuel tank with fuel bottle. 3. Connect 1.2v glow plug . 4. Start engine with a 12v starter. ( note the direction of the starter.) 5. After the engine has started, remove the 1.2v glow plug . Igniter igniter * follow the engine manufacturer instructio...

  • Page 24

    Your radio control model can move at high speed and therefore can cause injury to people or damage property. It is your responsibility to operate your model safely. For engine use, refer to the manual included with the engine. To prime the engine with fuel, press down the primer button. Attach one c...

  • Page 25

    Set triangle marks in the direction shown in fig.(1) 1 degree 1.5 degree fig.1 use rear tor-in adjuster. Front toe-in and toe-out setting toe-in toe-out toe-out neutral position steering rod front and rear shock angle setting firm front suspension, less steering. Soft front suspension, more steering...

  • Page 26

    Parts list for ultra-gtp, 911 rtr .28 & 2 sp ofn a description retail ofn a description retail 10010 clutch shoes black 3 shoes 13.95 34050 center bones, ultra gt, 2pcs 15.95 10040 3 pin flywheel, .21 corn type 14.95 34055 pins, lower rear arms 3x42.6mm 15.95 10069 red seal, silicone round, 2pcs 6.9...

  • Page 27: Blank

    Blank.

  • Page 28

    Racer’s name tel:( ) address city state zip dealer’s name tel: ( ) address city state zip ofna racing congratulates you on your purchase of our fine ofna product. With proper maintenance and han- dling this kit will provide many hours of enjoyment. The registration card should be filled out and mail...