Summary of Ultra LX ONE
Page 2
Tools not included in the kit included in the kit required for operation phillips type screw drivers ( l ) phillips type screw drivers ( s ) cutter curved scissors knife ca glue cross wrench masking tape spray paints brush precision caliper 1.5mm allen wrench 2mm allen wrench 2.5mm allen wrench 4mm'...
Page 3
Running a nitro kit is fun and easy, but to make this a safe • clean oil and dirt from chassis with a degreaser like simple green. And good experience you must observe a few rules. This kit is extremely fast, easily over 40mph, and can seriously precautions injure someone if you are not careful. • t...
Page 4
Plastic parts for use 40536 front c hub 40643 shock plastic parts 40643 shock cap washer 40643 shock plastic ball end (long) 40643 shock plastic ball end (short) 30751 diff. Case 30010 front and rear gear box 30751 diff. Case 30761 diff. Case 34063 rear lower arm 36011 front lower arm 30240 bumper 3...
Page 5
30674 servo saver 40019 front stiffener 41033 stone guard 16016 wing 30270 wing stay plastic parts for use symbols used throughout the instruction manual ensure free movement ensure free movement apply grease apply lubricant oil tighten tighten do not over tighten rotate direction rotate direction c...
Page 6
1 2 assembly of the front and rear diff. Assembly of the center diff. Build two differentials for front and rear. Step 2 step 3 step 4 step 5 step 1 1 step 1 step 2 step 3 step 5 step 4 *apply diff. Gear grease to the differential, during assembly. *fill the diff. Case to approx 80% with grease. *ap...
Page 7
3 assembly of the center diff. Motor mount *note: the holes for front diff. Mount are width. 30201 2 94004 3x12mm hex screw .....X2 3x12mm s ew cr e c me nt screw ce en m t 30653 30675 4 assembly of the front gear case step 1 step 2 30130 30630 30010 30630 30080 5x4mm 4x12mm 30673 s re c w e cem nt ...
Page 8
6 assembly of the knuckle arms step 1 step 2 step 3 assemble both right and left side. 36053 40520 36053 4mm nylon nut 4mm nylon nut 40528 36055 30656 4x4mm 34053 3 40527 40527 40536 8x12x0.3mm screw m t ce en 94034 4x4mm set screw .....X2 40218 8x12x0.3mm washer .....X2 94042 4mm nylon nut .....X4 ...
Page 9
9 assembly of the front stabilizer step 1 step 2 4 3x8mm 3x8x0.8mm 34027 3x8x0.8mm 3x3mm 3x18mm 30341 30403 3x8mm 40199 40199 94006 3x18mm hex screw .....X2 94002 3x8mm hex screw .....X2 94040 3x8x0.8mm washer .....X2 94033 3x3mm set screw .....X2 94035 3x8mm set screw .....X2 *makes two rods for le...
Page 10
12 assembly of the servo saver onto gear case step 1 step 2 5 3x15mm 3x10mm 3x15mm 40039 rew sc ement c screw e e c m nt 40039 94003 3x10mm hex screw .....X2 94021 3x15mm flat head hex screw .....X4 40039 3mm tapered washer(alum.) .....X4 13 assembly of the rear gear case step 1 step 2 30010 30130 3...
Page 11
15 assembly of the rear gear case step 1 step 2 6 40531 3x10mm 34033 3x25mm 3x20mm 3x18mm 3x20mm 3x18mm 30270 30270 30270 30270 30270 30270 30270 40531 3x25mm 94019 3x10mm flat head hex screw 90018 3x25mm cap screw 94007 3x20mm hex screw .....X4 94006 3x18mm hex screw .....X2 .....X1 .....X2 16 asse...
Page 12
18 assembly of the rear low arms into gear box assemble both right and left side. 3mm 3x25mm 94008 3x25mm hex screw .....X2 94006 3x18mm hex screw .....X2 34054 36171 3mm 3mm 3x18mm 3mm step 2 step 1 7 19 assembly of the rear stabilizer 94040 3x8x0.8mm washer .....X2 94002 3x8mm hex screw .....X2 3x...
Page 13
21 assembly of the front gear case onto chassis 94019 3x10mm flat head hex screw 94027 4x16mm flat head hex screw 94026 4x12mm flat head hex screw 4x16mm 3x25mm 4x16mm 3x10mm 4x12mm 30676 30240 .....X2 .....X4 .....X2 8 94023 3x25mm flat head hex screw .....X2 22 assembly of the center diff. Onto ch...
Page 14
23 assembly of the rear gear case onto the chassis 4x16mm 4x16mm 3x25mm 94023 3x25mm flat head hex screw 94027 4x16mm flat head hex screw .....X4 .....X2 9 36100 (86.5mm) *insert drive shaft into cap joint before assembly center diff. 24 assemble both right and left side. 94019 3x10mm flat head hex ...
Page 15
25 step 3 step 2 94003 3x10mm hex screw .....X2 assembly of the rear torque rad step 1 3x10mm 10 94007 3x20mm hex screw .....X1 94013 3x25mm hex screw .....X1 36850 36850 7mm ball .....X1 36700 36700 40108 36680 3x20mm 94041 3mm nylon nut .....X1 3mm 3x25mm 36680 7mm ball and socket .....X1 *approx....
Page 16
27 28 assembly of the battery tray bridge onto battery case 29 assembly of the speed control receiver wire into radio case assembly of the speed contrtol receiver onto battery case step 1 step 2 3x10mm 94002 3x8mm hex screw .....X2 11 speed contrtol receiver(option) 30662 30662 double sided tape 306...
Page 17
30 31 assembly of the servo wire into radio case 32 assembly of the battery case onto chassis assembly of the steering servo onto radio case 12 94040 3x8x0.8mm washer .....X4 94003 3x10mm hex screw .....X4 3x10mm 3x8x0.8mm 30662 94019 3x10mm flat head hex screw .....X3 94026 4x12mm flat head hex scr...
Page 18
33 34 assembly of the receiver into radio case 35 assembly of the steering rod onto redio case assembly of the radio case onto chassis 13 94019 3x10mm flat head hex screw .....X4 3x10mm 3x10mm receiver *plug in your steering servo to ch1 and speed control to ch2. 94002 3x8mm hex screw .....X2 37410 ...
Page 19
37 motor install 36 motor install 94038 3x12mm cap screw .....X2 14 motor (not included) *use notebook paper to set gear backlash between spur gear and clutch bell gear; apply pressure while tightening the engine. *if the space is not correct, the spur gear will be damaged. Notebook paper 94034 4x4m...
Page 20
39 40 assembly of the rear shocks assembly of the front and rear shocks 40090 1mm washer .....X2 40090 3.5mm o-ring .....X4 40090 2mm washer .....X2 2.6x5mm washer .....X4 fill the shocks with oil #40. 40640 40633 30403 40639 3 7 .5 m m correct shock assembly carefully screw the shock shaft into the...
Page 21
16 42 assembly of the rear shock absorber assemble both right and left sides. 94040 3x8x0.8mm washer .....X2 94041 3mm nylon nut .....X2 .....X2 94007 3x20mm hex screw 43 assembly of the wing 94004 3x12mm hex screw .....X2 44 assembly of the tires and wheels 86082 86082 86056 86056 3x20mm 3mm 3x8x0....
Page 22
45 assembly of the tire onto front knuckle and rear hub 40550 wheel nut .....X4 40550 46 body install 17 30677 cut out body reamer (not included.) step 1 step 2 cut out the body as shown. Before cutting and making holes in the body, put the unpainted body on the chassis to confirm the mounting posit...
Page 23: Setting Guide
Front camber angle setting rear camber angle setting place the model car on flat surface. Raise the chassis to it's maximum clearance before the wheels leave the ground. Adjust the length of the front and rear upper arms so that the wheels are right angle to the ground. The camber angle adjustment c...
Page 25
30777 seal, o-ring (large) diff case 3.95 30779 misc. Parts, old diff & (k) 9.95 30664 pinion 13t 5mm shaft 12.95 30780 pins, 2x12.8mm for dif 2pcs 3.95 30666 pinion 15t 5mm shaft 12.95 30901 cap joint w /shaft f/r diff 11.95 30667 pinion 16t 5mm shaft 12.95 30911 cap joint w /shaft, brake 11.95 306...
Page 27
Racer’s name tel:( ) address city state zip dealer’s name tel: ( ) address city state zip ofna racing congratulates you on your purchase of our fine ofna product. With proper maintenance and han- dling this kit will provide many hours of enjoyment. The registration card should be filled out and mail...