Ofna Racing X2 TRUGGY Instruction Manual - Failure to Not Read And

Summary of X2 TRUGGY

  • Page 2

    Option things need besides the kit radio control unit 12v battery for starter box (must have) glow plug heat with battery & charger # 10227....$$19.95 (please note ofna glow heats available) aa batteries ( 12 pcs ) for radio note: carefully read the instruction manual of your 2 channel radio control...

  • Page 3

    Aa batteries ( 12 pcs ) tools not included in kit, but needed to maintain your car. Phillips type screw drivers ( l ) phillips type screw drivers ( s ) needle nose pliers cutter curved scissors #91009 $5.95 instant cement cross wrench #17109 $3.95 grease you need to get batteries for the radio trans...

  • Page 4: Failure to Not Read And

    Running a nitro kit is fun and easy, but to make this a safe • clean oil and dirt from chassis with a degreaser like simple green. And good experience you must observe a few rules. This kit is extremely fast, easily over 40mph, and can seriously precautions injure someone if you are not careful. • t...

  • Page 5

    41053 front upper arm 40534 arm holder 30802 throttle linkage plastic 41036 center diff. Mount 41008 shock plastic parts 40643 shock plastic parts 40643 shock cap washer 40643 shock plastic ball end (long) 40643 shock plastic ball end (short) 40669 bumper 40538 diff. Case 40533 front and rear gear b...

  • Page 6

    40542 win stay 40541 receiver box 41033 stone guard 40540 rear upper right/front bumper 34026 plastic parts servo fixing 41034 chassis brace plastic parts for use 41052 servo saver 16015 wing.

  • Page 7

    40011 1 2 3 assembly of the front and rear diff. Assembly of the front and rear diff. Assembly of the center diff. Step 1 step 2 36053 8x16mm ball bearing 94034 4x4mm set screw 40010 2.5x13.8mm pin .....X4 .....X4 .....X4 .....X2 40009 p6 o-ring builds two differentials for front and rear. .....X16 ...

  • Page 8

    4 5 6 assembly of the center diff. Assembly of the front gear case assembly of the front arms holder step 2 4x35mm 4x16mm adjust the backlash with the shims. 40024 13x16x0.2mm shim 36053 8x16mm ball bearing .....X2 94015 4x35mm hex screw .....X2 94011 4x16mm hex screw .....X2 2 * * use 10000 weight ...

  • Page 9

    7 8 9 assembly of the front shock stay assembly of the knuckle arms assembly of the knuckle arms into front lower arms 3 step 2 step 4 94009 4x10mm hex screw .....X4 step 1 step 2 94003 3x10mm hex screw .....X4 41009 3x28mm cap screw .....X2 41010 41035 41009 3x10mm 3x10mm 3x10mm 4x10mm 40527 knuckl...

  • Page 10

    10 11 12 assembly of the front upper arms assembly for both right and left side. Assembly of the front stabilizer assembly for both right and left side. Assembly of the front stabilizer 4 36850 7mm ball and socket .....X2 94008 3x25mm hex screw .....X2 approx. 9mm 11 ¡g 36861 36850 41053 40602 3x25m...

  • Page 11

    13 14 15 assembly of the front stabilizer assembly of the servo saver 5 step 1 step 2 assembly of the servo saver 40037 steering plat screw .....X2 40024 3x8mm washer .....X2 40073 4x8mm ball bearing .....X2 94041 3mm nylon nut 3mm 3mm .....X2 do not over tighten ensure free movement 94033 3x3mm set...

  • Page 12

    16 17 18 assembly of the steering tie-rod assembly of the steering tie-rod onto gear box assembly of the rear gear case step 1 6 40039 3m tapper washer .....X2 40038 7mm ball .....X4 94021 3x15mm flat head hex screw .....X2 40548 nylon nut(thin type) .....X2 66.5 mm 11 ¡g step2 assembly for both rig...

  • Page 13

    19 20 21 assembly of the rear universal joint assembly of the rear shock stay assembly of the wing stay 7 step 1 step 2 5x4mm set screw .....X1 4x12mm hex screw .....X4 3x10mm hex screw 41009 3x28mm cap screw .....X2 3x12mm hex screw .....X2 4x12mm 5x4mm 4x12mm 40689 step 1 step 2 .....X3 41010 3x10...

  • Page 14

    19 20 21 assembly of the rear universal joint assembly of the rear shock stay assembly of the wing stay 7 step 1 step 2 94036 5x4mm set screw .....X1 94010 4x12mm hex screw .....X4 94003 3x10mm hex screw 41009 3x28mm cap screw .....X2 94004 3x12mm hex screw .....X2 4x12mm 5x4mm 4x12mm 40689 step 1 s...

  • Page 15

    22 23 assembly of the wing stay assembly of the rear wheel hubs assembly of the rear suspension arms 8 step 1 step 2 assemble both right and left sides 4x16mm 94009 4x10mm hex screw .....X1 94034 4x4mm set screw .....X2 94041 3mm nylon nut .....X2 3mm 3mm 4x10mm 4x20mm 94011 4x16mm hex screw .....X4...

  • Page 16

    25 26 27 9 assembly of the rear suspension arms assembly for both right and left side. Assembly of the rear stabilizer rods 94035 3x8mm set screw .....X2 94022 3x18mm hex screw .....X2 makes two rods for left and righthand-side. 3x8mm 40540 40540 30403 30341 3x18mm 94008 3x25mm hex screw .....X2 55 ...

  • Page 17

    30 assembl of the stone guard and brace y assembly of the center diff. Mount 10 29 assembly of the brake cam into center diff. 28 step 1 .....X2 30212 5x8mm flange ball bearing 94033 3x3mm set screw .....X1 94017 3x8mm flat head hex screw .....X4 94019 3x10mm flat head hex screw .....X2 step 2 step ...

  • Page 18

    31 32 33 assembly of the front gear case onto chassis assembly of the center diff. Onto chassis assembly of the rear gear case onto chassis 94019 3x10mm flat head hex screw .....X1 94019 3x10mm flat head hex screw .....X2 3x10mm 4x20mm 4x20mm 41035 11 94026 4x12mm flat head hex screw .....X4 94028 4...

  • Page 19

    34 35 36 assembly of the front servo assembly of the radio tray assembly of the radio tray and receiver box 94003 3x10mm hex screw .....X2 step 1 step 3 30560 37410 40541 40541 receiver battery case 40580 40580 3x10mm step 1 step 2 use the original battery case or rechargeable hump pack battery. Con...

  • Page 20

    37 38 39 assembly of the radio tray onto chassis assembly of the fuel tank assembly of the fuel tank post onto chassis 13 41035 41035 step 1 step 2 step 3 3x10mm 40620bk 40620bk 94019 3x10mm flat head hex screw .....X2 3x10mm 3x10mm 41035 41051 3x10mm 3x10mm 3x10mm 3x10mm 41035 41037 94019 3x10mm fl...

  • Page 21

    40 41 42 assembly of the fuel tank onto chassis assembly of the clutch assembly of the clutch and engine mount 14 step 1 step 2 step 1 step 2 10013 10101 3x12mm 3x12mm *place the clutch shoes with the clutch springs over the 3 pins of the flywheel. *using a flat screw driver or needle nose pliers an...

  • Page 22

    43 44 45 assembly of the engine onto chassis assembly of the manifold and muffler assembly of the throttle linkage 15 step 1 step 2 step 2 cut off the servo saver as shown. 30661 10114 4x10mm 5x4mm 10120 10052 41050 94033 3x3mm set screw .....X2 2mm nut .....X2 40060 nylon nut .....X1 2x8mm screw 2....

  • Page 23

    46 47 48 assembly of the throttle linkages into brake lever adjusting the engine control linkages assembly of the air filter 16 step 1 step 2 fuel tube #158 approx. 1mm gap (neutral) (throttle high) (brake) idling adjusting screw approx. 0.5mm carburetor is opening fully * use the screw provided wit...

  • Page 24

    49 50 assembly of the front shocks assembly of the rear shocks step 1 step 2 step 3 step 4 step 5 step 7 step 6 *assemble 2 sets for front *assemble 2 sets for rear 40643 (short) 40054 (short) 2.6x5mm 41005 41013 40058 41008 41017 1.Pull down piston and pour oil into shock cylinder. 2.To remove air ...

  • Page 25

    51 52 53 assembly of the front shock absorber assembly of the rear shock absorber assembly of the front bumper 18 assembly for both right and left side. Assembly for both right and left side. 3mm 3x20mm 4x16mm step 1 step 2 .....X3 94004 3x12mm hex screw 94003 3x10mm hex screw .....X6 3x10mm 3x12mm ...

  • Page 26

    54 55 56 assembly of the fuel tube and pressure tube assembly of the wing assembly of the tires and wheels 19 connect to carbulater. Connect to fuel nipple. Connect to fuel tank nipple. Connect to pressure nipple. Step 1 step 3 step 2 in s t a n t g l u e apply instant glue into the groove of the wh...

  • Page 27

    57 assembly of the tire onto front knuckle and rear hub 20 assembly for both right and left side. 58 cut out the body as shown. Use a neutral detergent to remove any dirt and oil. Mask the windows from the inside with masking tape. Paint the body with polycarbonate spray paints. Spray paint making t...

  • Page 28

    1 2v . Starter box (not included) 59 mounting body 21 1.2v 60 starting of the engine 1. Turn on transmitter and then receiver. 2. Fill fuel tank with fuel bottle. 3. Connect 1.2v glow plug starter. 4. Start engine with 12v starter. ( note the direction of the starter.) 5. After the engine be started...

  • Page 29

    Steering ackerman location front sway bar preload 1 2 3 mm x2-crt set-up sheet driver:_________________ front suspension rear suspension shock spring: _______blue___________ shock spring: _______blue___________ shock piston: standard drilled shock piston: standard drilled shock oil wt: ________50___...

  • Page 31

    Steering ackerman location front sway bar preload 1 2 3 mm x2-crt set-up sheet driver:_________________ front suspension rear suspension shock spring: _______blue___________ shock spring: _______blue___________ shock piston: standard drilled shock piston: standard drilled shock oil wt: ________50___...

  • Page 33

    Ofna description retail ofna description retail 10013 sho es,alum silver-1.7gw /spring 29.95 40560 servo saver c o n. Plate h.C. 12.5 10098 clutch nut, sg shaft 4.95 40568 fro nt plate g raph ite 31.95 10101 springs,clutch,go ld 1.1m 3pcs 4.95 40570 steering knuckle cnc h.C. 99.95 10114 flat head en...

  • Page 35

    Racer’s name tel:( ) address city state zip dealer’s name tel: ( ) address city state zip ofna racing congratulates you on your purchase of our fine ofna product. With proper maintenance and han- dling this kit will provide many hours of enjoyment. The registration card should be filled out and mail...