1. DL manuals
  2. Ogura
  3. Cutter
  4. HBC-16R
  5. Instruction Manual

Ogura HBC-16R Instruction Manual - Table of Contents

Summary of HBC-16R

  • Page 1

    1 before installing and operating this machine, read, understand and follow all instructions and operating procedures. Keep these instructions with the machine. Instruction manual r.

  • Page 2: Table of Contents

    2 meaning of "caution" and "warning" indications caution: indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury. This is also used to alert against unsafe practices associated with events that could lead to personal injury. Warning: indicates a pot...

  • Page 3

    3 1. Before operating tool read instruction manual. 2. Keep work area clean • cluttered areas and benches invite injuries. 3. Consider work area environment • do not expose tool to rain. • do not use tool in damp or wet locations. • keep work area well lit. • do not use tool in presence of flammable...

  • Page 4

    4 20. Check for damaged parts • before using the tool, carefully check all parts for damage, including guards, to ensure that they will operate correctly and perform their intended function. • check for any misalignment or binding of moving parts; damaged or broken parts and mountings; and any other...

  • Page 5: Caution

    5 caution ● cut pieces may fly off during cutting. Confirm the safety of surroundings before cutting. ● keep fingers and face away from the cutting area. Cut pieces may fly off and cause injury to the operator. ● material is ejected at end of cut. Be sure that ejected slug cannot fall and cause inju...

  • Page 6: Parts Names

    6 parts names trigger switch trigger switch trigger switch oil filler bolt oil filler bolt hydraulic cylinder cutter rod bar holder blade a blade b hold bolt stopper hbc-16r hydraulic pump case hbc-613, 816 hbc-313, 316, 16r blade a hold bolt hold bolt bar holder cutter rod cutter rod blade b hydrau...

  • Page 7: Specifications

    7 specifications ■ specifications model hbc-313 hbc-613 hbc-316 115 v / 230 v a.C 580 w 710 w 580 w 50 / 60 hz single-phase weight 5.4 kg 7.3 kg 5.8 kg dimensions (l ✕ w ✕ h) 362 ✕ 205 ✕ 106.5 mm 447 ✕ 151 ✕ 110 mm 378 ✕ 205 ✕ 108 mm tensile strength max. Dia. Tensile strength max. Dia. Tensile stre...

  • Page 8

    8 model hbc-520 hbc-22 115 v / 230 v a.C 1,330 w 700 w 50 / 60 hz single-phase weight 12.2 kg 14.2 kg dimensions (l ✕ w ✕ h) 396 ✕ 112 ✕ 220 mm 414 ✕ 112 ✕ 238 mm tensile strength max. Dia. Tensile strength max. Dia. 560 n / mm 2 620 n / mm 2 (57 kg / mm 2 ) 22 mm (#7) cutting capacity (63 kg / mm 2...

  • Page 9: Operating Procedure

    9 operating procedure this tool is electro-hydraulic rebar cutter to be designed to cut reinforcing bars. Read, understand and follow all safety instructions and operating procedures. If you do not understand the instructions or if conditions are not correct for proper operations, do not operate thi...

  • Page 10: Warning

    10 operating procedure 4. Pull the trigger switch to start cutting operation. The cutter rod will move forward to cut the rebar. Keep the switch depressed until the cutter rod stops at the end of its stroke. 5. Release the switch when the cut is completed and the cutter rod has reached the end of it...

  • Page 11: Warning

    11 the motor body can be rotated though 360 degrees, in either direction, during operation. This feature is particularly useful when working in awkward or narrow areas as it allows the operator to position the tool in the best position for easy operation. The funtion of the return valve is to allow ...

  • Page 12

    12 model part number size hbc-313 (ø 3 ~ ø 13 mm) 6071060 10 (width) ✕ 5 (thickness) ✕ 12 (length) mm hbc-613 (ø 3 ~ ø 13 mm) 6402170 11 (width) ✕ 5 (thickness) ✕ 17 (length) mm hbc-316 (ø 3 ~ ø 16 mm) 6071060 10 (width) ✕ 5 (thickness) ✕ 12 (length) mm hbc-16r (ø 3 ~ ø 16 mm) 6071060 10 (width) ✕ 5...

  • Page 13: Blades Replacement Procedure

    13 blades replacement procedure ensure that blade a on the bar holder and blade b on the cutter rod are fitted in their correct respective positions. 1. Undo the bolts and the washers that hold blade a and blade b. 2. Remove dirt and clean the surfaces where the new blades are to be fitted. 3. Fit b...

  • Page 14: Adding Oil

    14 adding oil this rebar cutter is electro-hydraulic. When shipped from the factory, it was filled with oil. Do not attempt to add oil as long as the tool performs well. Over a period of time the oil level will gradually go down. Eventually this will cause a noticeable dropping off in performance. W...

  • Page 15: Trouble Shooting

    15 trouble shooting problem c u t t e r r o d w i l l n o t extend. Insufficient power to cut rebar. Oil leaks. Motor not working. Motor slow or erratic. Cause insufficient oil cutter rod has not returned completely due to build up of debris between cutter rod and bar holder. Cutter rod has not retu...

  • Page 16

    2661 hongo, ebina city, kanagawa-pref., japan 243-0417 tel : 046-238-1285 fax : 046-238-4188 iojin.8503400/0810