1. DL manuals
  2. Ogura
  3. Cutter
  4. HCC-16DF
  5. Instruction Manual

Ogura HCC-16DF Instruction Manual

Manual is about: cordless rebar cutter

Summary of HCC-16DF

  • Page 1

    1 before installing and operating this machine, read, understand and follow all instructions and operating procedures. Keep these instructions with the machine. Instruction manual hcc-16df hcc-19df r.

  • Page 2: Table of Contents

    2 read, understand and follow all safety instructions and operating procedures. If you do not understand the instructions, or if conditions are not correct for proper operation, do not operate the machine. Consult your supervisor or other responsible person. Important safety instructions ..............

  • Page 3: Warning

    3 warning 1. Before use, read this instruction manual thoroughly. • do not expose the charger and battery to rain or use them in damp or wet locations, as this may cause overheating or electric shock. 2. Keep work area clean. • cluttered areas and benches invite injuries. 3. Keep the work area well ...

  • Page 4: Caution

    4 caution warning 1. Do not cover or clog the motor air vents as this may cause the motor to overheat, resulting in smoke, fire and explosion. 2. This tool is a hydraulic tool powered by electricity. When the temperature is low, hydraulic oil may become solid and tool cannot perform well. Idle tool ...

  • Page 5: Name of The Parts

    5 model hcc-16df hcc-19df motor dc magnet motor battery lithium-ion battery (bl1830) 3.0 ah, 22-minutes charge voltage 18v dc max. Cutting capacity (dia.Mm) grade 40 ~ grade 60 grade 40: tensile strength 16 mm 5/8" 20 mm 3/4" 490 n / mm 2 70,000 psi grade 60: tensile strength 620 n / mm 2 90,000 psi...

  • Page 6

    6 names of the parts ■ standard accessories (hcc-16df) battery charger (dc18ra) ---------------------------- 1 battery (bl1830) ----------------------------------------- 1 battery cover ---------------------------------------------- 1 hex wrenches (m3,m4,m5,m6) ---------- one each spanner (14 mm ✕ 1...

  • Page 7: Battery Charge

    7 battery charge 1. Plug the battery charger into the proper ac voltage source. Charging light will flash in green color repeatedly. 2. Insert the battery cartage into charger until stops adjust- ing to the guide of charger. Terminal cover of charger can be opened with inserting and closed with pull...

  • Page 8

    8 battery charge 1. Inserting the battery cartridge into charger brings out last preset brief melody sound of completed charging. 2. Removing and re-inserting it within five seconds after this action makes the melody sound change/ 3. Every time removing and re-inserting it within another five second...

  • Page 9: Caution

    9 battery charge conditioning charge can extend the life of battery by automatically searching the optimum charging condition for the batteries in every situation. The battery employed in the following conditions repeatedly requires "conditioning charge" to prevent fast wear out. In that case, yello...

  • Page 10: Operating Procedure

    10 operating procedure read, understand and follow all safety instructions and operating procedures. If you do not understand the instructions, or if conditions are not correct for proper operation, do not operate this tool. Consult your supervisor or other responsible person. Switch lock operation ...

  • Page 11: Warning

    11 operating procedure 3. Push in the switch lock on side a. The switch is unlocked and the trigger can be operated. 4. Press the trigger switch to start cutting operation. The cutter rod will move forward to cut the rebar. Keep the switch depressed until the cutter rod stops at the end of its strok...

  • Page 12: Warning

    12 the motor body can be rotated though 360 degrees, in ei- ther direction, during operation. This feature is particularly useful when working in awkward or narrow areas as it al- lows the operator to position the tool in the best position for easy operation. The function of the return valve is to a...

  • Page 13: Blades Replacement Procedure

    13 blades replacement procedure ensure that blade a, on the bar holder and blade b, on the cutter rod are fitted in their correct respective positions. 1. Undo the bolts and the washers that hold blade a and blade b. 2. Remove dirt and clean the surfaces where the new blades are to be fitted. 3. Fit...

  • Page 14: Adding Oil

    14 adding oil this cordless rebar cutter is electro-hydraulic. When shipped from the factory, it was filled with oil. Do not attempt to add oil as long as the tool performs well. Over a period of time the oil level will gradually go down. Eventually this will cause a noticeable dropping off in perfo...

  • Page 15: Trouble Shooting

    15 note: the internal components of the pump and piston area have very close tolerances and are sensitive to damage from dust, dirt, contamination of the hydraulic fluid or improper handling. The disassembly of the pump housing requires special tools and training, and should only be attempted by qua...

  • Page 16

    2661 hongo ebina city, kanagawa-pref., japan 243-0417 tel : 046-238-1285 fax : 046-238-4188 iojin.00000/0904.