Summary of VX Series
Page 1
Vx series floor scale instruction manual.
Page 3
1. Introduction ..................................................................................................................... 1 1.1. Safety precautions ................................................................................................. 1 2. Installation ...........................
Page 5
Vx series floor scale en-1 1. Introduction this manual contains installation, operation and maintenance instructions for the vx series floor scale. 1.1. Safety precautions please follow these safety precautions: never operate in hazardous areas. The vx series platforms may be used in dry environment...
Page 6
En-2 vx series floor scale 2.2. Foot adjustment 1. The four feet must be adjusted out of the shipping position and into the operating position. Use a 7/8” wrench to loosen each foot and extend them to 4-1/2” (114mm) measured from the top surface of the platform. 2. At this position use a 3/4” wrench...
Page 7
Vx series floor scale en-3 connecting the platform cable 1. Remove the two fasteners on the junction box access cover located on the side panel of the platform. 2. Slide the junction box forward and out of the compartment. Remove the plastic top cover from the junction box. 3. Loosen the water-tight...
Page 8
En-4 vx series floor scale connecting the indicator cable 1. Route the cable from the platform to the location where the indicator will be mounted. 2. The cable near the platform must lie free without tension. Excessive tension may result in weighing errors. 3. Ensure that the cable will be protecte...
Page 9
Vx series floor scale en-5 3. Operation for setup, calibration, and proper operation, refer to the instruction manual supplied with the indicator. Refer also to section 4.3 below for floor scale capacity and readability information. 3.1. Operating limits although the floor scales have extremely rugg...
Page 10
En-6 vx series floor scale technical data 4.3. Specifications table 3. Floor scale specifications platform models vx2500l vx5000l vx10000l vx5000x vx10000x platform dimensions (w x d x h) 4’ x 4’ x 4.5” / 1,219 x 1,219 x 114 mm 5’ x 5’ x 4.5” / 1,524 x 1,524 x 114 mm capacity x e min 2,500 lb x 0.5 ...
Page 11
Vx series floor scale en-7 4.5. Dimensions figure 4. Floor scale dimensions table 5. Floor scale dimensions models dimensions floor scale platform foot centers a h (nominal) w l vx2500l / vx5000l 4’ / 1,219 mm 4.5” / 114 mm 42.5” / 1,080 mm 42.5” / 1,080 mm vx5000x 5’ / 1,524 mm 4.5” / 114 mm 54.5” ...
Page 12
En-8 vx series floor scale 4.6. Installation of foot plates and ramps two foot plates are included with the floor scale. Ramps are available separately. Installation of floor plates or ramps is optional but must be done before final placement of the floor scale. Refer to figures 5 and 6 for mounting...
Page 13
Vx series floor scale en-9 4.7. Conformance iso 9001 registration in 1994, ohaus corporation, usa, was awarded a certificate of registration to iso 9001 by bureau veritus quality international (bvqi), confirming that the ohaus quality management system is compliant with the iso 9001 standard’s requi...
Page 14
En-10 vx series floor scale limited warranty ohaus products are warranted against defects in materials and workmanship from the date of delivery through the duration of the warranty period. During the warranty period ohaus will repair, or, at its option, replace any component(s) that proves to be de...
Page 17
Ohaus corporation 7 campus drive suite 310 parsippany, nj 07054 usa tel: (973) 377-9000 fax: (973) 944-7177 www.Ohaus.Com with offices worldwide *80252765* p/n 80252765 b © 2011 ohaus corporation, all rights reserved printed in china.