P3 International P5090 Operating Manual

Other manuals for P5090: Specification Sheet
Manual is about: Telephone Recorder

Summary of P5090

  • Page 1

    P5090 telephone recorder operating manual p3 international corporation limited warranty p3 international corporation (“p3”) warrants to the original retail purchaser only, that its product is free from defects in material or workmanship under the condition of normal use and service for a period of s...

  • Page 2

    Welcome: congratulations on your purchase of the p5090 telephone recorder! You now possess one of the most sophisticated telephone recording devices on the market today. With features like time and date stamp, caller id, extended recording mode, and timer recording modes, the telephone recorder can ...

  • Page 3

    This tape was likely recorded using the voice controlled system (vcs). Vcs automatically starts and stops the recording when it detects conversations. When the recorder starts it takes a fraction of a second for the motor to respond. This slight delay can lead to the beginning of the first word bein...

  • Page 4

    Quick start instructions: if you want to get a fast start, use the following instructions for immediate results. We recommend that you come back and review the full instructions for details on all the features of the telephone recorder. 1. Connect power and telephone cables. 2. Press reset button on...

  • Page 5

    Allow you to record just the first few minutes of each phone call. Enough to identify the called or calling party and the subject of the conversation. As the entire conversation is not recorded, you can fit many more telephone calls on each cassette. Over 300 calls per cassette! (using both sides of...

  • Page 6

    The other end of the supplied cable to the line in connector (14) on the telephone recorder. Reset: a microprocessor reset button is located on the bottom of the unit. The unit must be reset after installation. Push the button with a small screwdriver or pen. Rear panel (please refer to diagram): th...

  • Page 7

    West (w). Please see the diagram for more detail. Setup timer recording mode: with unit in stand by mode (no tape transport keys pressed) press e and w keys simultaneously. This will place recorder in programming mode. Rec duration will be displayed. If no further keypresses are detected, unit will ...

  • Page 8

    Line activation mode is set as the default from the factory and is used in most applications. See sections below on vcs mode and timer recording mode for more details. Press the stop/eject key to open cassette door. Insert cassette. Close cassette door. To record telephone calls press record tape tr...

  • Page 9

    Line activation mode is set as the default from the factory and is used in most applications. See sections below on vcs mode and timer recording mode for more details. Press the stop/eject key to open cassette door. Insert cassette. Close cassette door. To record telephone calls press record tape tr...

  • Page 10

    West (w). Please see the diagram for more detail. Setup timer recording mode: with unit in stand by mode (no tape transport keys pressed) press e and w keys simultaneously. This will place recorder in programming mode. Rec duration will be displayed. If no further keypresses are detected, unit will ...

  • Page 11

    The other end of the supplied cable to the line in connector (14) on the telephone recorder. Reset: a microprocessor reset button is located on the bottom of the unit. The unit must be reset after installation. Push the button with a small screwdriver or pen. Rear panel (please refer to diagram): th...

  • Page 12

    Allow you to record just the first few minutes of each phone call. Enough to identify the called or calling party and the subject of the conversation. As the entire conversation is not recorded, you can fit many more telephone calls on each cassette. Over 300 calls per cassette! (using both sides of...

  • Page 13

    Quick start instructions: if you want to get a fast start, use the following instructions for immediate results. We recommend that you come back and review the full instructions for details on all the features of the telephone recorder. 1. Connect power and telephone cables. 2. Press reset button on...

  • Page 14

    This tape was likely recorded using the voice controlled system (vcs). Vcs automatically starts and stops the recording when it detects conversations. When the recorder starts it takes a fraction of a second for the motor to respond. This slight delay can lead to the beginning of the first word bein...

  • Page 15

    Welcome: congratulations on your purchase of the p5090 telephone recorder! You now possess one of the most sophisticated telephone recording devices on the market today. With features like time and date stamp, caller id, extended recording mode, and timer recording modes, the telephone recorder can ...

  • Page 16: Operating Manual

    P5090 telephone recorder operating manual p3 international corporation limited warranty p3 international corporation (“p3”) warrants to the original retail purchaser only, that its product is free from defects in material or workmanship under the condition of normal use and service for a period of s...