Paasche F88P-2-0-6 Operating Instructions
INSTRUCTIONS AND PARTS LIST, F88P-8/31/2011
Supersedes Instruction & Parts List F88P-11/13/2009
WARNING: Spray materials may be harmful if inhaled or allowed
to come into contact with skin or eyes. Consult the product label and
Material Safety Data Sheet supplied for the spray material. Follow
all safety precautions. CAUTION:
Well Ventilated Area
Required to remove fumes, dust or overspray. Check
compatibility of materials used with Polyethylene
container and PVC Fluid Hose. Secure airhose and fluid
hose wrench tight for safety and to prevent leaks.
M a x i m u m A i r P r e s s u r e 8 0 P . S . I .
M a x i m u m F l u i d P r e s s u r e 4 5 P . S . I .
F88P-2-0-6
DUAL FLUID SPRAY GUN
OPERATING INSTRUCTIONS AND REPLACEMENT PARTS
INTRODUCTION:
This Manual Spray Gun requires clean dry air regulated
from 6 to 8 C.F.M. at 60 to 80 lbs. air pressure depending
on the size of atomizing heads to be used. Paasche
Regulator & Condenser Units are recommended for
attaching to air supply line to remove water, oil, rust or
scale and help insure a quality finish of coating.
AIR AND FLUID CONNECTIONS:
1. Air Connection: To remove any accumulated foreign
matter blow out all hoses before using.
a. Air supply to Spray Gun must be turned off
before attaching fittings to the Air Inlet.
b. Attach HT-1/4 Air Hose to the Air Outlet on the
Air Regulator and Air Inlet on the bottom of the
handle on the Spray Gun.
2. Fluid Hose Connection: HPT-1/4 PVC Fluid Hose
with Stainless Steel Couplings should be long enough
to form a loop below the Spray Gun at all times when
using fluid hose to feed material to the Spray Gun
(two required).
a. Attach NS-3/8 Nut and HNS-1/4-3/8 Nipple,
Stainless Fittings, to the fluid inlets of the two
Fluid Bodies.
b. Attach opposite ends, NS-3/8 Nut and HNS-1/4-
3/8 Nipple, Stainless Fittings, to containers of
respective materials being sprayed.
3. Fluid Container Connection: When using USP-QT
(QT./.946 l) Plastic Bottle Assemblies, make sure
Screw Covers are tightened securely so fluid will not
leak at Bottle connections.
4. Tighten all Air and Fluid connections securely.
OPERATION:
1. After hose connections have been made, regulate the
air pressure to about 40 lbs. and then pull trigger back
slowly.
a. The first 1/4" of trigger stroke opens the Air
Valve which operates both the cylinders.
b. Continued pull on the trigger opens both of the
atomizing Spray Heads for spraying.
2. The U-1460 Adjusting Nut (part 39) can be used to
regulate desired amount of fluid to the automatic
Spray Head.
3. Dual Fluid Spray Guns are designed to atomize and
mix fluid materials outside the atomizing aircaps. This
prevents materials from hardening inside the spray
gun.
4. The U-28-12 Packing Washers (part 6) should be
replaced periodically.
a. Fill packing cavity with 3 new U-28-12 Packing
Washers and replace U-29 Packing Gland (part
7), DU-30 Spring (part 8) and U-31 Spring Seat
(part 9) in position.
b. A few drops of oil should occasionally be
applied to the U-2506 Piston Leather (part Z) to
keep it pliable.
Paasche Airbrush Company
4311 North Normandy Avenue
Chicago, IL 60634-1395
Phone: 773-867-9191 • Fax: 773-867-9198
Website: paascheairbrush.com
E-Mail: info@paascheairbrush.com
Printed in the U.S.A.