PAC SWI-CP2 Manual - Swi-Cp2
SWI-CP2
Universal Steering Wheel Control Retention Interface
TM
Steering Wheel Control Interface
P ifi A
C
ti
Rev. 051617
P
age 4
C
opyright © 2017. All rights reserved. PAC is a Power Brand of AAMP Global.
PAC
-audio.com
7HVWLQJ9HUL¿FDWLRQ
1. Turn
t
he ignition on. The red LED on the interface will turn on & the +12v accessory output wire will turn on.
2. 9HULI\WKDWDOO6:&DUHIXQFWLRQLQJSURSHUO\7KHJUHHQ/('ZLOOÀDVKHDFKWLPHLWVHHVDVWHHULQJZKHHOEXWWRQSUHVVHG
3. Turn
off the vehicle & remove the key. In vehicles equipped with retained accessory power (RAP) the accessory output and
t
he red LED will remain active & keep the radio on for 10 minutes unless the driver side door is opened. In vehicles that do not
support RAP the LED and accessory output will shut off when the key is switched or removed from the ignition.
3/($6(127(7KLVVHFWLRQRQO\DSSOLHVWREXWWRQUHDVVLJQPHQWZLWKLQDFRQ¿JXUDWLRQ,I\RXDUHXVLQJWKH&3LQ
manual programming mode (all vehicle dipswitches up) please refer to the “Manually Mapping the SWC Buttons” section
on page 3
If you wish to re-assign the SWC functions or utilize short press long press dual command functionality you will need to follow the
steps outlined in this section. Please read each of the following steps to familiarize yourself with the process before beginning.
7KHLQWHUIDFHPXVWEHSURJUDPPHGLQWKHVSHFL¿FRUGHUVKRZQLQWKHFKDUWEHORZ
1. Turn
t
he key to the ignition position. The LED will illuminate red.
2. Press and hold the programming button on the side of the interface until the LED illuminates green. Release the
programming button.
3. Within 7 seconds, press the button that is to be learned on the steering wheel. The LED will turn red when the steering
wheel button is pressed. At this point you have two options:
a. For short press functionality:
Release the button on the steering wheel. The LED will change back to green.
b. For
long
press
functionality:
&RQWLQXHWRKROGWKHEXWWRQXQWLOWKH/('ÀDVKHVEHWZHHQUHGDQGDPEHU5HOHDVH
t
he button and the LED will change back to green.
4. If you need to program more buttons, repeat step 3 for each additional audio function on the steering wheel.
5. If you come across a function in the chart that your steering wheel does not have, or you do not want to program, press
and release the program button on the side of the interface to skip that function. The LED will turn off and back on when
t
he skip has been done successfully.
6. 2QFHSURJUDPPLQJLVFRPSOHWHGZDLWVHYHQVHFRQGV7KH/('ZLOOÀDVKJUHHQWLPHVLQGLFDWLQJWKHHQGRISURJUDPPLQJ
7. Test the interface for proper functionality. Whenever a SWC button is pressed the LED on the interface should blink green.
If any function does not work, repeat the programming steps.
The SWC can always be restored to default settings by pressing and holding the programming button on the side of the interface
XQWLOWKH/('LOOXPLQDWHVJUHHQ5HOHDVHWKHSURJUDPPLQJEXWWRQWKHQZDLWVHFRQGVIRUWKH/('WRÀDVKWLPHV
SWC Button Re-assignment Procedure
Alpine
JVC
Kenwood
Clarion
Other
Pioneer
Sony
Fusion
1
Volume +
Volume +
Volume +
Volume +
Volume +
Volume +
Volume +
Volume +
2
Volume -
Volume -
Volume -
Volume -
Volume -
Volume -
Volume -
Volume -
3
Mute
Mute
Mute
Mute
Mute
Mute
Mute
Mute
4
P
reset +
Source
Source
Source
P
reset +
P
reset +
P
reset +
Source
5
P
reset -
Track +
P
lay
Search +
P
reset -
P
reset -
P
reset -
Track +
6
Source
Track -
Track +
Search -
Source
Source
Source
Track -
7
Track +
Band / Disc +
Track -
Band
Track +
Track +
Track +
A
udio
8
Track -
P
reset / Disc -
Disc / FM +
Send / End
Track -
Track -
Track -
P
ower
9
P
ower
Select
Disc / AM -
Send
Band
Band
Band
10
Enter/Play
Att
enuation
A
nswer
End
A
nswer
P
hone Menu
Reject Call / Source
(Bluetooth
equipped radios
only)
11
Band / Program
P
hone Receive
Voice Dial
VR
End
A
nswer Call
A
nswer / End Call
12
Receive
P
hone Reject
On Hook
P
TT
End Call
VR
13
End
Voice Dial
Off Hook
VR
14
VR
P
ower
Mute (Multimedia
units only)
15
P
reset +
- Advent, Boyo, Dual, Lightning Audio, Jensen, Rockford Fosgate & Visteon
- Jensen & Advent ONLY
Optional Programming Order