Pace DC60Xu Quick Start Manual - Problem
DC60Xu HD
Power
If the installed system does not seem to be working properly,
first make sure that all the cables are securely connected, then carry out the
following checks, in the order shown.
Problem
Suggested solution
Further checks, if there is still a problem
There is nothing
illuminated on your
digital adapter’s
front panel.
Power may not be reaching your digital adapter. Make sure
that the external power supply unit is properly plugged in. If
there is a switch by the wall AC power outlet, switch it to ON.
Check that the wall AC power outlet is working (for example by plugging
in a lamp).
The remote control
does not operate
your digital adapter.
Check that nothing is blocking the path from your remote
control to the front panel.
Check that your remote control is currently set to operate your digital
adapter (consult the instructions supplied with your remote control).
If your remote control will still not operate your digital adapter, replace
the batteries in your remote control.
There is no picture
on your TV screen.
Your TV and other equipment may not be turned on. Check
that they are plugged into AC power outlets and turned on.
If your TV and digital adaper are connected using a coaxial
RF cable, make sure your TV and digital adapter are both set
to the
same channel (3 or 4).
Check that you have selected the appropriate video input on your TV.
If the video path between your digital adapter and your TV loops through
other equipment (such as a VCR) you may need to turn on this equipment.
If your TV and digital adaper are connected using a coaxial RF cable, try
switching your TV and digital adapter to the other channel (3 or 4).
There are black
bars on the sides of
your TV screen.
Check the screen settings on your TV (refer to the TV user
guide to make sure it is in 16x9 mode).
If you do not subscribe to an HD service, you will not be able to view HD
channels and may see the black bars on the sides of your TV screen,
indicating that the picture is in standard-definition.
Check that the program is transmitted in HD.
There is no sound. Check that any audio cables between your TV and any
attached audio equipment are securely and correctly
connected.
Check that you have not muted the sound on your TV and/or any
attached audio equipment. Adjust the volume control on your TV.
If you can hear only mono sound, first check that the program is likely to
have stereo sound (an old movie, for example, may not be in stereo).
If you are still having problems
contact your cable company.
SOLVING PROBLEMS
Place the batteries (supplied) into your remote control.
After you install your digital adapter, the only way to change channels
is with the supplied remote control.
If you need further help, for example to program the remote control to
operate your TV, refer to the instructions supplied with the remote control.
USING YOUR REMOTE CONTROL
HIGH-DEFINITION CONNECTION
STANDARD-DEFINITION CONNECTION
1. Connect the supplied coxial RF cable from the cable service to the
connector marked
CABLE IN on your digital adapter, as shown below.
2. Connect the supplied HMDI cable between the
HDMI connector
on your digital adapter and the
HDMI connector on your HDTV.
3. Connect the external power supply unit (supplied) to the connector
marked
POWER on your digital adapter.
4. After you have made the connections between your digital adapter
and your HDTV, connect your HDTV and the external power supply
unit to the AC power supply.
PLACING YOUR DIGITAL ADAPTER
Set this switch to Channel 3
Following Installation
If you have followed the steps and have picture and sound,
congratulations, you have successfully installed your Pace high-
definition digital adapter.
If you are experiencing problems, please consult the “Solving
Problems” guide located to the right.
Note: If your digital adapter requires activation, contact your cable
company.
Enjoy viewing all of your favorite TV shows, movies and sports
games with digital picture and sound.
ENJOY DIGITAL TV!
ABOUT YOUR DIGITAL ADAPTER
CABLE IN
From cable
service provider
S POWER LED
Lights when your
digital adapter is fully on
POWER INPUT
Make this connection
last of all
TO TV
RF output to
the TV
HDMI
Video and audio output
for digital HDTV
CHANNEL 3/4
Switch for tuning your
digital adapter (if required)
Front Panel
Rear Panel
To the wall
AC outlet
From your cable service
Digital Adapter
Supplied
HDMI cable
HDTV
Supplied RF cable
After you have made the connections between the cable service, your
digital adapter and your TV, place your digital adapter in a suitable
location, observing the ventilation requirements set out in the safety
information overleaf.
Make sure there is nothing blocking the path from your remote control
to the digital adapter’s front panel. You can “pair” the remote control
and digital adapter. This enables the remote control to operate the
digital adapter if the digital adapter is hidden from view. For more
information, consult the instructions supplied with your remote control.
• Youcanplaceyourdigital
adapter below or beside
your TV.
• Oncetheremotecontrol
and digital adapter are
“paired”, you can use
the adhesive fasteners
(supplied) to attach your
digital adapter to the side
or back of your TV.
DC60Xu HD
Power
CABLE IN
RF IN
CABLE
SERVICE
To the wall
AC outlet
From your cable service
Digital Adapter
Supplied RF cable
CABLE IN
RF IN
SDTV
RF cable
1. Connect the supplied coxial RF cable from the cable service to the
connector marked
CABLE IN on your digital adapter, as shown below.
2. Connect another coxial RF cable between the
TO TV connector on your
digital adapter and the ANTENNA IN/RF IN connector on your SDTV.
3. Connect the external power supply unit (supplied) to the connector
marked
POWER on your digital adapter.
4. After you have made the connections between your digital adapter
and your SDTV, connect your SDTV and the external power supply
unit to the AC power supply.
5. Make sure your TV is tuned to channel
3, and set the switch on the back of
your digital adapter to channel 3.
Note: Some parts of the country use
channel 4. If you do not have a picture,
you may need to switch both your TV
and digital adapter to channel 4.
Digital Adapter
(exact model may
differ slightly from
that shown)
Coaxial RF Cable
External 5V
Power Supply Unit
Remote Control
(exact model may differ
slightly from that shown)
AA Batteries
(for your
remote
control)
Adhesive
Fasteners
WHAT’S IN THE BOX?
HDMI
®
Cable
1
2
3
4
5
6
7
8
9
0
GUIDE
INFO
MENU
EXIT
PAGE
MUTE
TV
CABLE
POWER
LAST
LANG