Pacemaster bronze xrc owner’s manual aerobics inc., 34 fairfield place west caldwell, nj 07006, (973) 276-9700 www.Pacemaster.Com part # bronze xrc rev. 11/13/07 1.
2 table of contents introduction 3 important safety instructions 4 assembly instructions 5-17 installation requirements 5 unpacking your recumbent 5 tools required for assembly 5 box contents 6 hardware package contents 7 assembling your recumbent 8-17 the pacemaster bronze xrc bike control panel 18...
Introduction congratulations and thank you for choosing pacemaster – your partner in achieving your fitness goals and mastering your well-being. Pacemaster’s advanced digital technology allows your equipment to process information instantly, anticipating and adjusting to meet your needs. Think of it...
Important safety instructions read these instructions before using your recumbent caution: before starting any exercise program, contact your personal physician and have a complete physical. This is highly recommended if you have not been on a regular exercise program within the last year, or are ov...
Assembly instructions installation requirements your pacemaster should be installed indoors on a flat, level surface near a 120volt/ grounded outlet. You must have a minimum of 2 feet of clearance on all sides between the bike and any wall or obstruction. Tip: if you are installing your pacemaster o...
1. Box contents h an d ra il ( 59 ) se at (1 02 ) b ac kr es t ( 10 3) r e a r s ta bil iz er (7 4 ) fr on t iliz er sta b (6 6) l eft p ed al (1 19 ) r ig ht p ed al (1 20 ) l eft r ea r c ov e ( 48 ) r ig ht r ea r c ov er (4 9) k no b ( 10 5) pla sti c c u sh io n ( 90 ) se at b as e ( 51 ) h an ...
Hardware kit contents (1 17 ) o p en s p an ne r— 1p c s (1 09 ) b olt m 8х 56 — 4c s (1 10 )m 8 a cr on n ut — 4p c s (1 12 )s p rin g w as he r m 8x 2.0 t— 4p c s (1 13 )w as he r 2 0x 9x 2.0 t— 4p c s (1 14 ) a lle n b olt m 8х 45 — 2p c s (1 10 )m 8 a co rn n ut — 2p c s (1 12 )s p rin g w as he...
1. Assemble the front stabilizer a step 1a: as shown to the right, attach the front stabilizer (66) to the frame (1) with bolts (109), washers (113) (112) and acorn nuts (110), then tighten the nut with the included wrench (117) or a 13mm wrench or socket. Note: the front stabilizer (66) is the one ...
2. Assemble the rear stabilizer a step 2a: as shown to the right, attach the rear stabilizer (74) to the frame (1) with bolts (109), washers (113) (112) and acorn nuts (110), then tighten with the included wrench (117) or a 13mm wrench or socket. Spring washer m8х2.0t—2pcs(112) washer 20х9х2.0t—2pcs...
3. Assemble the computer mast c b a step 3c: insert tube (80) into main frame (1) with screw (108) and washer (5) by 6mm allen wrench. Connect cable wire (16) to knob (105). Then slide knob (105) in to upright tube (80) and secure with screw (122) using a phillips screwdriver. Step 3b: connect wires...
4. To install the batteries step 4b: install 4 aa batteries (not included) step 4a: remove battery cover. Battery cover a batteries b c step 4c: after you install the batteries, reinstall the battery cover close batter cover. Battery cover 11.
5. To assemble the computer step 5c: attach the computer (97) to the upright (80) with the 4 phillips head screws (100) removed in step a above. Do not pinch the wires when securing the computer (97) to the mast (80). Step 5b: connect the 2 pairs of contact heart rate wires (98) to (83) and (99) to ...
6. To assemble the seat, handrails, and seat sliding base step 6a: attach the seat (102) to the seat base (51) with bolts (108), washers (5) and 6mm allen wrench (118). A self tapping screw st4.0x25 4pcs (41) allen bolt m6 x 35 2pcs (91) washer 18x9x2.0t 6pcs(5) allen bolt m8x15 4pcs (108) allen bol...
B step 6d: 1. Install both plastic seat stops (90) to the seat rail (84), with bolts (91), using the 4mm allen wrench (116) (one seat stop on each side). 2. Connect the contact heart rate wires (17) & (63) as shown in fig b. Step 6c: rotate the handle (93) of the seat base (51) upwards in the direct...
7. To assemble the backrest washer 18 x 9 x 2.0t 4pcs (5) allen bolt m8 x 1 54pcs (108) a step 7a: install the seat back (103) to the seat base using bolts (108), and flat washers (5), then tighten using the 6mm allen wrench (118). 15.
8. Install the transport handle 如 示 運 m 內 右圖所 ,用螺絲(108),華司(5)將搬 扶手(96)與主架(1)組立,用 6m step 8a: install the transport handle (96) to the frame (1) with bolts (108), washers (5) tighten bolts (108) using the 6mm allen wrench (118). Washer 18 x 9 x 2.0t 2pcs (5) allen bolt m8 x 15 2pcs (108) a 16.
9. Assemble and install the pedals step 9b: the pedals are stamped on the threaded end of the axle with the letter “r” and “l” for right and left respectively. Right and left sides are determined as you would use the recumbent bike. Install the right pedal on the right crank arm using the included w...
Computer operation instructions heart rate recovery reset set mode 1. Computer states: three states of the computer: 1. Power up state: when the batteries are first installed you will hear a long beep and the entire display will be illuminated for 2 seconds, it will then prompt you to enter the time...
2. Setting the date & time install 4 aa batteries: if you installed the batteries during set up, and the left hand digit of the time display is still flashing (see below), proceed as outlined below. If the left-hand digit of the time display is not flashing remove one battery, wait 10 seconds reinst...
Setting parameters for manual “time” will flash, and can be adjusted using the set button or reset using the reset button. Press enter (mode) to save value & move to next parameter to be adjusted. Continue through all desired parameters, start pedaling to begin your workout. Note: resistance can be ...
Display function chart no. Display range of display setting instructions 1 time 0:00—99:00 0—99 circle a. When the preset time is 0:00, time will count up. B. When the time is 01:00-99:00, time will count down. 2 distance 0.0—99.50 0—99.50 circle a. When the preset distance is 0:00, distance will ac...
3. Button functions: heart rate recovery reset set mode 1. Set button - is used to adjust the set value (such as time,distance,calories,pulse) press this button to enter the setting mode, the set value will flash and at this moment you can circularly adjust the value of each function. 2. Mode button...
5. Monitoring heart rate: contact heart rate – your pacemaster bronze xrc comes equipped with contact heart rate monitoring capability through contact heart rate grips. Your hands need to be in contact with both the left & right contact sensors to achieve a heart rate reading. Your heart rate will b...
Bronze xrc 11/13/07 24.
Pacemaster bronze xrc technical specifications boxed dimensions: 65 in x 30 in x 15 in assembled dimensions: 68”l x 29” w x 49”h boxed weight: 127 lbs. Assembled weight: 110lbs. Frame: high tensile steel rpm range: 0 to 255 rpm adjustable in increments of 1 resistance range: 0 to 8 levels workout pr...
