Warning: if the information in this manual is not followed exactly, a fire or explosion may result causing property damage, personal injury or loss of life. -- do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. -- what to do if you smel...
2 contents caution ...................................................................................................... 3 safety ......................................................................................................... 4 maintenance ....................................................
3 important: when lit for the first time, the appliance will emit a slight odor for a couple of hours. This is due to the curing of paints, seal- ants and lubricants used in the manufacturing process. This condition is temporary. Open doors and windows to ventilate area. If optional fan kit has been...
4 safety • due to high temperatures, this gas appliance should be located out of traffic and away from furniture and dra- peries. • children and adults should be alerted to the hazards of high surface temperature and should stay away to avoid burns or clothing ignition. • young children should be ca...
5 installation caution: a gas appliance must not be connected to a chimney flue servicing a separate solid fuel burning appli- ance. This appliance must be properly connected to a venting system. This heater is equipped with a blocked vent shutoff system designed to protect against improper vent- in...
6 clearances the brentwood insert is designed to be installed into a masonry or a factory built zero clearance fireplace, or built in with the optional mirage zero-clearance kit. The masonry fireplace must be built according to the requirements of the standards for chimneys, fireplaces, vents and so...
7 venting caution: use only a flue liner system approved by the local gas authority and install in accordance with the manufacturers instructions. Consult local and/or national building codes before altering fireplace. The chimney must be relined with a minimum 4" flue liner (fig. #7). A combination...
8 fig. # 10 fig. # 9 fig. # 11 smoke stick spill switch rocker switch gas valve thermopile blocked vent shutoff system installation this appliance is equipped with a blocked vent shutoff system. The switch assembly is shipped with the appliance. 1) unravel wire, feed through front grommeted hole loc...
9 fig. # 16 fig. # 14 fig. # 13 fig. # 15 fig. # 12 trim retaining screw part f trim d part a d part c part b trim part c d part a surround assembly warning: failure to position the parts in accordance with these diagrams or failure to use only parts specifically approved with this appliance may res...
10 fig. # 17c step 4 top left log placement (log #4) fig. # 17b step 1 rear log placement (log #1) step 3 lower right log placement (log #3) step 2 lower left log placement (log #2) log set unpack and inspect log set. There should be a total of 7 logs. Gas and vent connections should be made before ...
11 step 7 rear right log placement (log #7) step 6 rear left log placement (log #6) 2 7 5 3 6 4 fig. # 17f 1 step 5 top right log placement (log #5) fig. # 17e fig. # 17d.
12 fig. # 18 fig. # 19 fig. # 21 fig. # 20 embers frame tabs latch fan cover weld nuts glowing embers note: use only glowing embers supplied with the appliance. Use of any other materials or incorrectly placed embers may cause an incorrect flame pattern, sooting and/or delayed ignition. Place 10 to ...
13 fig. #24 fig. #23 fig. #22 louver installation unpack and inspect all parts. A flathead or a #2 robertson screwdriver is required to install the louvers. 1) fasten top louver to the top casing with the screws provided (see fig. #22). 2) fasten bottom louver to the hinge brackets at the bottom of ...
14 for your safety read before lighting lighting instructions to turn off gas to appliance 1. Set wall thermostat to lowest setting, if applica- ble. 2. Turn off all electric power to the appliance if service is to be performed. 3. Push in gas control knob slightly and turn clockwise to "off". Do no...
15 fig. #25 manual hi-lo control knob adjustment rod fig. #26 first fire when lit for the first time, the appliance will emit a slight odor for a couple of hours. This is due to the curing of paints, sealants and lubricants used in the manufacturing process. This condition is temporary. Open doors a...
16 fig. # 30 burner orifice pilot burner assembly rear attachment points burner assembly front attachment points burner removal caution: turn off gas and electrical power supply and allow ample time for unit to cool before pro- ceeding. 1) fold down the bottom louver, if installed, to access the ove...
17 hex key pilot burner orifice pilot hood propane conversion the appliance can be converted to propane gas as follows: burner orifice 1) ensure the burner, pilot and fuel supply are turned off, and the appliance has cooled. 2) note log positions and carefully remove them (if in- stalled). 3) remove...
18 fig. # 36 fig. # 34 l2 (black) 115 volts 60 hz 0.5 amperes blower rocker switch speed control snap disc switch fig. # 35 g (green) l1 (white) optional blower electrical supply: circulating air blower electrical rating: 115v, 60 hz, 80 watts. For your protec- tion against shock hazard, use only a ...
19 fig. # 39 fig. # 38 4) run the power cord to the outside of the appliance through the foremost 1-1/2" grom- met located on the right side of the firebox support and casing side. 5) fasten the thermo-switch through the two holes in the rear of the firebox with the two #8 - 1/2" sheet metal screws ...
20 replacement parts see fig. # 40 (when ordering, include part number with description) item description part no. Item description part no. 1 ...... Vent connector plate .................................................... Minb.1649 2 ...... Spill switch ...............................................
21 fig. # 40 11 14 20 5 13 9 17 2 5 4 19 1 16 15 8 6 10 7 12 5 18 3 14.
22 burner replacement parts see fig. # 41 (when ordering, include part number with description) item description part no. Item description part no. 1 ...........Burner plate assembly .....................Brna.1980 2 ...........Pilot assembly, ng .............................. 5009.157 .............E...
23 label for use with/ natural gas/ lp-gas/ en case d’emploi avec: du gaz naturel du gaz lp minimum supply pressure / pression minimum d’alimentation: 5.0 in/wc / 5.0 po/c.E. 11.5 in/wc / 11.5 po/c.E. (for the purpose of input adjustment/dans le but de regler l’alimenation) (1.25 kpa) (2.86 kpa) man...
Printed in canada pacific energy fireplace products ltd. Box 1060, duncan, bc v9l 3y2 phone: 250-748-1184 web site: http://www.Pacificenergy.Net.