1. DL manuals
  2. Pacific Energy
  3. Indoor Fireplace
  4. SUMMIT WOOD INSERT DESIGN-A
  5. Installation And Operating Instructions Manual

Pacific Energy SUMMIT WOOD INSERT DESIGN-A Installation And Operating Instructions Manual - Contents

Summary of SUMMIT WOOD INSERT DESIGN-A

  • Page 1

    160309-20 suminserta 5055.511 safety notice if this stove is not properly installed, a house fire may result. For your safety, folow the installation directions. Consult local building or officials about restrictions and installation inspection requirements in your area. Important: these instruction...

  • Page 2: Contents

    2 suminserta 160309-20 contents safety .............................................................................................. 3 clearances ...................................................................................... 3 masonry or factory built fireplace ................................

  • Page 3

    Suminserta 160309-20 3 safety read all instructions before installing and using this appliance. Failure to follow in- structions may result in property damage, bodily injury, or even death. We strongly recommend that smoke detectors be installed. If smoke detectors have been previously installed, yo...

  • Page 4

    4 suminserta 160309-20 16” non-combustible hearth 34 1/2” 23 1/8” 18” 8” 8” * fireplace hearth (measured without the insert): the non-combustible fireplace hearth must be raised 2" above an adjacent combustible floor and extend 16" in front and 8" beyond each side of the fireplace opening. A non-com...

  • Page 5

    Suminserta 160309-20 5 installation your insert is designed to be installed into a masonry or factory built zero-clearance fireplace. The masonry fireplace must be built according to the requirements of the standard of chimneys, fireplaces, vents and solid fuel burning ap- pliances, n.F.P.A. 211 (la...

  • Page 6

    6 suminserta 160309-20 full flue liner - (required in canada) 1) measure the chimney height from the top of the existing flue to the floor of the hearth. This will allow extra length of liner for flashing and rain cap. 2) feed the stainless steel liner from top of the chimney, through the damper are...

  • Page 7

    Suminserta 160309-20 7 surround assembly and installation 1) lay part a, b and c face down on a flat non-marring surface. Fasten together with 1/4" x 1/2" bolts and nuts provided through holes at points “d” (fig. #5 and 8). 2) lift the surround assembly to the upright position and make sure the fron...

  • Page 8

    8 suminserta 160309-20 10) position the decorative bay stove top onto the firebox top. Ensure that the studs align with the slotted tabs, one on each side of the firebox top. Secure in place with 1/4” nuts provided. 11) replace the front panels and ashlip in the reverse order to their removal. 8) sl...

  • Page 9

    Suminserta 160309-20 9 combustion air consult local building codes regarding combustion air sup- ply. Intake or combustion air can be supplied to the insert in one of two ways: 1) outside air supply: remove cover from ash clean out in existing fireplace. Place a rodent screen in place of the cover. ...

  • Page 10

    10 suminserta 160309-20 operation wood selection this heater is designed to burn natural wood only. Higher efficiency and lower emissions generally result when burning air-dried seasoned hardwoods, as compared to softwoods or too green or freshly cut hardwoods. Wood should be properly air dried (sea...

  • Page 11

    Suminserta 160309-20 11 ash removal whenever ashes get 3 to 4 inches deep in your firebox, and when fire has burned down and cooled, remove excess ashes. Leave an ash bed approximately 1 inch deep on the firebox bottom to help maintain a hot charcoal bed. Disposal of ashes ashes should be placed in ...

  • Page 12

    12 suminserta 160309-20 chimney fires the result of excessive creosote buildup is a chimney fire. Chimney fires are dangerous. Chimney inside temperatures can exceed 2000 degrees f. This causes much higher than normal temperatures in the chimney and on its exterior sur- faces thus ignition of nearby...

  • Page 13

    Suminserta 160309-20 13 maintenance 1. Burn wood only, dry and well seasoned. The denser or heavier the wood when dry, the greater its heat value. This is why hardwoods are generally preferred. Green or wet wood will cause a rapid buildup of creosote. If you feel it is necessary to burn wet or unsea...

  • Page 14

    14 suminserta 160309-20 appendix a troubleshooting problem cause cure excessive creosote 1) wood is too wet - use dry wood buildup 2) turning down air control - do not turn down until: too soon a) there is a good bed of coals b) the wood is charred 3) draft too low - improper chimney height and/or d...

  • Page 15: Pacific Summit Wood Stoves

    Suminserta 160309-20 15 item size part number a 1 1/2” x 4 1/2” x 1 1/4” (39 mm x 115 mm x 32 mm) 248.0 b 4” x 4 1/2” x 1 1/4” (102 mm x 115 mm x 32 mm) 246.0 c 7 1/4” x 4 1/2” x 1 1/4” (184 mm x 115 mm x 32 mm) 245.0 d 9” x 4 1/2” x 1 1/4” (230 mm x 115 mm x 32 mm) 5096.99 e 9” x 3 1/2” x 1 1/4” (1...

  • Page 16

    16 suminserta 160309-20 4......Casing top, back ............................................................. 3502 5......Casing top, front ........................................................ 3502.51 6......Casing back...............................................................3504.001 7a......

  • Page 17

    Suminserta 160309-20 17 6 6 6 fig. # 18.

  • Page 18

    18 suminserta 160309-20 understanding & operating your pacific energy stove the pacific energy line of wood stoves is a culmina- tion of years of research and development. Designed to be efficient, clean-burning and user-friendly, this heater will give you years of warm service. However, a knowledge...

  • Page 19: Caution

    Suminserta 160309-20 19 label minimum clearance to combustibles (measured from insert body) a) adjacent sidewall 216 mm / 8.5 in. B) mantle 533 mm / 21 in. C) top facing 533 mm / 21 in. D) side facing 216 mm / 8.5 in. • installanduseonlyinaccordancewiththemanufacturer’sinstallationandoperatinginstru...

  • Page 20

    Pacific energy fireplace products ltd. Technical support: 1 887 715-2398 www.Pacificenergy.Net 2975 allenby rd., duncan, b.C. V9l 6v8 printed in canada.