1. DL manuals
  2. Pacific Energy
  3. Indoor Fireplace
  4. SUMMIT WOOD INSERT DESIGN-A
  5. Nstallation And Operating Instructions

Pacific Energy SUMMIT WOOD INSERT DESIGN-A Nstallation And Operating Instructions - Contents

Summary of SUMMIT WOOD INSERT DESIGN-A

  • Page 1

    260407-20 suminserta 5055.511 safety notice if this stove is not properly installed, a house fi re may result. For your safety, folow the installation directions. Consult local building or offi cials about restrictions and installation inspection requirements in your area. Important: these instructi...

  • Page 2: Contents

    2 suminserta 260407-20 contents safety .............................................................................................. 3 clearances ...................................................................................... 3 masonry or factory built fireplace ................................

  • Page 3

    Suminserta 260407-20 3 safety read all instructions before installing and using this appliance. Failure to follow in- structions may result in property damage, bodily injury, or even death. We strongly recommend that smoke detectors be installed. If smoke detectors have been previously installed, yo...

  • Page 4

    4 suminserta 260407-20 16” non-combustible hearth 34 23 1/8” 18” 8” 8” non-combustible fi replace hearth requirements: the hearth may be fl ush with or raised above an adjacent combustible fl oor and must extend 16” in front and 8” beyond each side of the fi replace opening. Ember protection: combus...

  • Page 5

    Suminserta 260407-20 5 installation your insert is designed to be installed into a masonry or factory built zero-clearance fi replace. The masonry fi replace must be built according to the requirements of the standard of chimneys, fireplaces, vents and solid fuel burning appliances, n.F.P.A. 211 (la...

  • Page 6

    6 suminserta 260407-20 full flue liner - (required in canada) 1) measure the chimney height from the top of the exist- ing fl ue to the fl oor of the hearth. This will allow extra length of liner for fl ashing and rain cap. 2) feed the stainless steel liner from top of the chimney, through the dampe...

  • Page 7

    Suminserta 260407-20 7 surround assembly and installation 1) lay part a, b and c face down on a fl at non-marring surface. Fasten together with 1/4" x 1/2" bolts and nuts provided through holes at points “d” (fig. #5 and 8). 2) lift the surround assembly to the upright position and make sure the fro...

  • Page 8

    8 suminserta 260407-20 9) push the entire appliance back until the surround as- sembly is in contact with the fi replace. 10) position the decorative bay stove top onto the fi rebox top. Ensure that the studs align with the slotted tabs, one on each side of the fi rebox top. Secure in place with 1/4...

  • Page 9

    Suminserta 260407-20 9 combustion air consult local building codes regarding combustion air sup- ply. Intake or combustion air can be supplied to the insert in one of two ways: 1) outside air supply: remove cover from ash clean out in existing fi replace. Place a rodent screen in place of the cover....

  • Page 10

    10 suminserta 260407-20 operation wood selection this heater is designed to burn natural wood only. Higher effi ciency and lower emissions generally result when burning air-dried seasoned hardwoods, as compared to softwoods or too green or freshly cut hardwoods. Wood should be properly air dried (se...

  • Page 11

    Suminserta 260407-20 11 ash removal whenever ashes get 3 to 4 inches deep in your fi rebox, and when fi re has burned down and cooled, remove excess ashes. Leave an ash bed approximately 1 inch deep on the fi rebox bottom to help maintain a hot charcoal bed. Disposal of ashes ashes should be placed ...

  • Page 12

    12 suminserta 260407-20 chimney fires the result of excessive creosote buildup is a chimney fi re. Chimney fi res are dangerous. Chimney inside temperatures can exceed 2000 degrees f. This causes much higher than normal temperatures in the chimney and on its exterior surfaces thus ignition of nearby...

  • Page 13

    Suminserta 260407-20 13 maintenance 1. Burn wood only, dry and well seasoned. The denser or heavier the wood when dry, the greater its heat value. This is why hardwoods are generally preferred. Green or wet wood will cause a rapid buildup of creosote. If you feel it is necessary to burn wet or unsea...

  • Page 14

    14 suminserta 260407-20 appendix a troubleshooting problem cause cure excessive creosote 1) wood is too wet - use dry wood buildup 2) turning down air control - do not turn down until: too soon a) there is a good bed of coals b) the wood is charred 3) draft too low - improper chimney height and/or d...

  • Page 15

    Suminserta 260407-20 15 item size part number a 1 1/2” x 4 1/2” x 1 1/4” (39 mm x 115 mm x 32 mm) 248.0 b 4” x 4 1/2” x 1 1/4” (102 mm x 115 mm x 32 mm) 246.0 c 7 1/4” x 4 1/2” x 1 1/4” (184 mm x 115 mm x 32 mm) 245.0 d 9” x 4 1/2” x 1 1/4” (230 mm x 115 mm x 32 mm) 5096.99 e 9” x 3 1/2” x 1 1/4” (1...

  • Page 16: Replacement Parts

    16 suminserta 260407-20 ....... Surround trim, set (** over-size, not shown) ......................... Sins.3549 2..... Surround top (* standard-size) ............................. Sins.3516 ....... Surround top (** over-size, not shown) ................ Sins.3546 3..... Bay top (c/w washers and nut...

  • Page 17

    Suminserta 260407-20 17 fig. # 18.

  • Page 18

    18 suminserta 260407-20 understanding & operating your pacifi c energy stove the pacifi c energy line of wood stoves is a culmina- tion of years of research and development. Designed to be effi cient, clean-burning and user-friendly, this heater will give you years of warm service. However, a knowle...

  • Page 19: Caution

    Suminserta 260407-20 19 label minimum clearance to combustibles (measured from insert body) a) adjacent sidewall 216 mm / 8.5 in. B) mantle 533 mm / 21 in. C) top facing 533 mm / 21 in. D) side facing 216 mm / 8.5 in. • install and use only in accordance with the manufacturer’s installation and oper...

  • Page 20

    Pacific energy fireplace products ltd. Technical support: 1 887 715-2398 www.Pacifi cenergy.Net 2975 allenby rd., duncan, b.C. V9l 6v8 printed in canada.